[PATCH] Input: edt-ft5x06 - consolidate handling of number of electrodes

From: Dmitry Torokhov
Date: Wed Dec 09 2020 - 18:10:18 EST


Instead of using special-casing retrieval of number of X/Y electrodes
based on the firmware, let's select default values and mark registers as
non-existent on firmwares that do not support this operation.

Also mark "report rate" register as non-existent for generic firmwares as
having it set to 0 does not make sense.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx>
---
drivers/input/touchscreen/edt-ft5x06.c | 43 ++++++++++----------------
1 file changed, 17 insertions(+), 26 deletions(-)

diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index 6ff81d48da86..2eefbc2485bc 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -69,6 +69,9 @@
#define EDT_RAW_DATA_RETRIES 100
#define EDT_RAW_DATA_DELAY 1000 /* usec */

+#define EDT_DEFAULT_NUM_X 1024
+#define EDT_DEFAULT_NUM_Y 1024
+
enum edt_pmode {
EDT_PMODE_NOT_SUPPORTED,
EDT_PMODE_HIBERNATE,
@@ -977,8 +980,7 @@ static void edt_ft5x06_ts_get_defaults(struct device *dev,
}
}

-static void
-edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data *tsdata)
+static void edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data *tsdata)
{
struct edt_reg_addr *reg_addr = &tsdata->reg_addr;

@@ -997,21 +999,17 @@ edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data *tsdata)
if (reg_addr->reg_report_rate != NO_REGISTER)
tsdata->report_rate = edt_ft5x06_register_read(tsdata,
reg_addr->reg_report_rate);
- if (tsdata->version == EDT_M06 ||
- tsdata->version == EDT_M09 ||
- tsdata->version == EDT_M12) {
+ tsdata->num_x = EDT_DEFAULT_NUM_X;
+ if (reg_addr->reg_num_x != NO_REGISTER)
tsdata->num_x = edt_ft5x06_register_read(tsdata,
reg_addr->reg_num_x);
+ tsdata->num_y = EDT_DEFAULT_NUM_Y;
+ if (reg_addr->reg_num_y != NO_REGISTER)
tsdata->num_y = edt_ft5x06_register_read(tsdata,
reg_addr->reg_num_y);
- } else {
- tsdata->num_x = -1;
- tsdata->num_y = -1;
- }
}

-static void
-edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
+static void edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
{
struct edt_reg_addr *reg_addr = &tsdata->reg_addr;

@@ -1041,22 +1039,25 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)

case EV_FT:
reg_addr->reg_threshold = EV_REGISTER_THRESHOLD;
+ reg_addr->reg_report_rate = NO_REGISTER;
reg_addr->reg_gain = EV_REGISTER_GAIN;
reg_addr->reg_offset = NO_REGISTER;
reg_addr->reg_offset_x = EV_REGISTER_OFFSET_X;
reg_addr->reg_offset_y = EV_REGISTER_OFFSET_Y;
reg_addr->reg_num_x = NO_REGISTER;
reg_addr->reg_num_y = NO_REGISTER;
- reg_addr->reg_report_rate = NO_REGISTER;
break;

case GENERIC_FT:
/* this is a guesswork */
reg_addr->reg_threshold = M09_REGISTER_THRESHOLD;
+ reg_addr->reg_report_rate = NO_REGISTER;
reg_addr->reg_gain = M09_REGISTER_GAIN;
reg_addr->reg_offset = M09_REGISTER_OFFSET;
reg_addr->reg_offset_x = NO_REGISTER;
reg_addr->reg_offset_y = NO_REGISTER;
+ reg_addr->reg_num_x = NO_REGISTER;
+ reg_addr->reg_num_y = NO_REGISTER;
break;
}
}
@@ -1195,20 +1196,10 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
input->id.bustype = BUS_I2C;
input->dev.parent = &client->dev;

- if (tsdata->version == EDT_M06 ||
- tsdata->version == EDT_M09 ||
- tsdata->version == EDT_M12) {
- input_set_abs_params(input, ABS_MT_POSITION_X,
- 0, tsdata->num_x * 64 - 1, 0, 0);
- input_set_abs_params(input, ABS_MT_POSITION_Y,
- 0, tsdata->num_y * 64 - 1, 0, 0);
- } else {
- /* Unknown maximum values. Specify via devicetree */
- input_set_abs_params(input, ABS_MT_POSITION_X,
- 0, 65535, 0, 0);
- input_set_abs_params(input, ABS_MT_POSITION_Y,
- 0, 65535, 0, 0);
- }
+ input_set_abs_params(input, ABS_MT_POSITION_X,
+ 0, tsdata->num_x * 64 - 1, 0, 0);
+ input_set_abs_params(input, ABS_MT_POSITION_Y,
+ 0, tsdata->num_y * 64 - 1, 0, 0);

touchscreen_parse_properties(input, true, &tsdata->prop);

--
2.29.2.576.ga3fc446d84-goog


--
Dmitry