[PATCH] Staging: silabs si4455 serial driver
From: József Horváth
Date: Thu Dec 10 2020 - 07:21:49 EST
I send this again, because my original mail content was corrupted.
This is a serial port driver for
Silicon Labs Si4455 Sub-GHz transciver.
Signed-off-by: József Horváth <info@xxxxxxxxxxx>
---
.../bindings/staging/serial/silabs,si4455.txt | 39 +
drivers/staging/Kconfig | 2 +
drivers/staging/Makefile | 1 +
drivers/staging/si4455/Kconfig | 8 +
drivers/staging/si4455/Makefile | 2 +
drivers/staging/si4455/TODO | 3 +
drivers/staging/si4455/si4455.c | 1465 +++++++++++++++++
drivers/staging/si4455/si4455_api.h | 56 +
8 files changed, 1576 insertions(+)
create mode 100644 Documentation/devicetree/bindings/staging/serial/silabs,si4455.txt
create mode 100644 drivers/staging/si4455/Kconfig
create mode 100644 drivers/staging/si4455/Makefile
create mode 100644 drivers/staging/si4455/TODO
create mode 100644 drivers/staging/si4455/si4455.c
create mode 100644 drivers/staging/si4455/si4455_api.h
diff --git a/Documentation/devicetree/bindings/staging/serial/silabs,si4455.txt b/Documentation/devicetree/bindings/staging/serial/silabs,si4455.txt
new file mode 100644
index 000000000000..abd659b7b952
--- /dev/null
+++ b/Documentation/devicetree/bindings/staging/serial/silabs,si4455.txt
@@ -0,0 +1,39 @@
+* Silicon Labs Si4455 EASY-TO-USE, LOW-CURRENT OOK/(G)FSK SUB-GHZ TRANSCEIVER
+
+Required properties:
+- compatible: Should be one of the following:
+ - "silabs,si4455" for Silicon Labs Si4455-B1A or Si4455-C2A (driver automatically detects the part info),
+ - "silabs,si4455b1a" for Silicon Labs Si4455-B1A,
+ - "silabs,si4455c2a" for Silicon Labs Si4455-C2A,
+- reg: SPI chip select number.
+- interrupts: Specifies the interrupt source of the parent interrupt
+ controller. The format of the interrupt specifier depends on the
+ parent interrupt controller.
+- clocks: phandle to the IC source clock (only external clock source supported).
+- spi-max-frequency: maximum clock frequency on SPI port
+- shdn-gpios: gpio pin for SDN
+
+Example:
+
+/ {
+ clocks {
+ si4455_1_2_osc: si4455_1_2_osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <30000000>;
+ };
+ };
+};
+
+&spi0 {
+ si4455: si4455@0 {
+ compatible = "silabs,si4455";
+ reg = <0>;
+ clocks = <&si4455_1_2_osc>;
+ interrupt-parent = <&gpio>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ shdn-gpios = <&gpio 26 1>;
+ status = "okay";
+ spi-max-frequency = <3000000>;
+ };
+};
diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig
index 9b7cb7c5766a..2cf0c9bfe878 100644
--- a/drivers/staging/Kconfig
+++ b/drivers/staging/Kconfig
@@ -118,4 +118,6 @@ source "drivers/staging/wfx/Kconfig"
source "drivers/staging/hikey9xx/Kconfig"
+source "drivers/staging/si4455/Kconfig"
+
endif # STAGING
diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile
index 38226737c9f3..043c63287bc6 100644
--- a/drivers/staging/Makefile
+++ b/drivers/staging/Makefile
@@ -49,3 +49,4 @@ obj-$(CONFIG_QLGE) += qlge/
obj-$(CONFIG_WIMAX) += wimax/
obj-$(CONFIG_WFX) += wfx/
obj-y += hikey9xx/
+obj-$(CONFIG_SERIAL_SI4455) += si4455/
diff --git a/drivers/staging/si4455/Kconfig b/drivers/staging/si4455/Kconfig
new file mode 100644
index 000000000000..666f726f2583
--- /dev/null
+++ b/drivers/staging/si4455/Kconfig
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0
+config SERIAL_SI4455
+ tristate "Si4455 support"
+ depends on SPI
+ select SERIAL_CORE
+ help
+ This driver is for Silicon Labs's Si4455 Sub-GHz transciver.
+ Say 'Y' here if you wish to use it as serial port.
diff --git a/drivers/staging/si4455/Makefile b/drivers/staging/si4455/Makefile
new file mode 100644
index 000000000000..1a6474673509
--- /dev/null
+++ b/drivers/staging/si4455/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_SERIAL_SI4455) := si4455.o
diff --git a/drivers/staging/si4455/TODO b/drivers/staging/si4455/TODO
new file mode 100644
index 000000000000..aee5c7613b31
--- /dev/null
+++ b/drivers/staging/si4455/TODO
@@ -0,0 +1,3 @@
+TODO:
+ - add variable packet length support
+ - add firmware patching support in case of Si4455-C2A
diff --git a/drivers/staging/si4455/si4455.c b/drivers/staging/si4455/si4455.c
new file mode 100644
index 000000000000..15f45f19ffdb
--- /dev/null
+++ b/drivers/staging/si4455/si4455.c
@@ -0,0 +1,1465 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 József Horváth <info@xxxxxxxxxxx>
+ *
+ */
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/gpio/driver.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/spi/spi.h>
+#include <linux/uaccess.h>
+#include "si4455_api.h"
+
+#define PORT_SI4455 1096
+#define SI4455_NAME "si4455"
+#define SI4455_MAJOR 432
+#define SI4455_MINOR 567
+#define SI4455_UART_NRMAX 1
+#define SI4455_FIFO_SIZE 64
+
+#define SI4455_CMD_ID_EZCONFIG_CHECK 0x19
+#define SI4455_CMD_ID_PART_INFO 0x01
+#define SI4455_CMD_REPLY_COUNT_PART_INFO 9
+#define SI4455_CMD_ID_GET_INT_STATUS 0x20
+#define SI4455_CMD_REPLY_COUNT_GET_INT_STATUS 8
+#define SI4455_CMD_ID_FIFO_INFO 0x15
+#define SI4455_CMD_ARG_COUNT_FIFO_INFO 2
+#define SI4455_CMD_REPLY_COUNT_FIFO_INFO 2
+#define SI4455_CMD_FIFO_INFO_ARG_TX_BIT 0x01
+#define SI4455_CMD_FIFO_INFO_ARG_RX_BIT 0x02
+#define SI4455_CMD_ID_READ_CMD_BUFF 0x44
+#define SI4455_CMD_ID_READ_RX_FIFO 0x77
+#define SI4455_CMD_ID_WRITE_TX_FIFO 0x66
+#define SI4455_CMD_ID_START_RX 0x32
+#define SI4455_CMD_ARG_COUNT_START_RX 8
+#define SI4455_CMD_START_RX_ARG_RXTIMEOUT_STATE_ENUM_RX 8
+#define SI4455_CMD_START_RX_ARG_RXVALID_STATE_ENUM_RX 8
+#define SI4455_CMD_START_RX_ARG_RXINVALID_STATE_ENUM_RX 8
+#define SI4455_CMD_ID_START_TX 0x31
+#define SI4455_CMD_ARG_COUNT_START_TX 5
+#define SI4455_CMD_ID_CHANGE_STATE 0x34
+#define SI4455_CMD_ARG_COUNT_CHANGE_STATE 2
+#define SI4455_CMD_CHANGE_STATE_ARG_NEW_STATE_ENUM_READY 3
+#define SI4455_CMD_GET_CHIP_STATUS_REP_CMD_ERROR_PEND_MASK 0x08
+#define SI4455_CMD_GET_CHIP_STATUS_REP_CMD_ERROR_PEND_BIT 0x08
+#define SI4455_CMD_GET_INT_STATUS_REP_PACKET_SENT_PEND_BIT 0x20
+#define SI4455_CMD_GET_INT_STATUS_REP_PACKET_RX_PEND_BIT 0x10
+#define SI4455_CMD_GET_INT_STATUS_REP_CRC_ERROR_BIT 0x08
+#define SI4455_CMD_ID_GET_MODEM_STATUS 0x22
+#define SI4455_CMD_ARG_COUNT_GET_MODEM_STATUS 2
+#define SI4455_CMD_REPLY_COUNT_GET_MODEM_STATUS 8
+
+struct si4455_part_info {
+ u8 CHIPREV;
+ u16 PART;
+ u8 PBUILD;
+ u16 ID;
+ u8 CUSTOMER;
+ u8 ROMID;
+ u8 BOND;
+};
+
+struct si4455_int_status {
+ u8 INT_PEND;
+ u8 INT_STATUS;
+ u8 PH_PEND;
+ u8 PH_STATUS;
+ u8 MODEM_PEND;
+ u8 MODEM_STATUS;
+ u8 CHIP_PEND;
+ u8 CHIP_STATUS;
+};
+
+struct si4455_modem_status {
+ u8 MODEM_PEND;
+ u8 MODEM_STATUS;
+ u8 CURR_RSSI;
+ u8 LATCH_RSSI;
+ u8 ANT1_RSSI;
+ u8 ANT2_RSSI;
+ u16 AFC_FREQ_OFFSET;
+};
+
+struct si4455_fifo_info {
+ u8 RX_FIFO_COUNT;
+ u8 TX_FIFO_SPACE;
+};
+
+struct si4455_one {
+ struct uart_port port;
+ struct work_struct tx_work;
+};
+
+struct si4455_port {
+ struct mutex mutex;
+ int power_count;
+ struct gpio_desc *shdn_gpio;
+ struct si4455_part_info part_info;
+ struct si4455_modem_status modem_status;
+ struct si4455_iocbuff configuration;
+ struct si4455_iocbuff patch;
+ u32 tx_channel;
+ u32 rx_channel;
+ u32 package_size;
+ bool configured;
+ bool tx_pending;
+ bool rx_pending;
+ u32 current_rssi;
+ struct si4455_one one;
+};
+
+static struct uart_driver si4455_uart = {
+ .owner = THIS_MODULE,
+ .driver_name = SI4455_NAME,
+#ifdef CONFIG_DEVFS_FS
+ .dev_name = "ttySI%d",
+#else
+ .dev_name = "ttySI",
+#endif
+ .major = SI4455_MAJOR,
+ .minor = SI4455_MINOR,
+ .nr = SI4455_UART_NRMAX,
+};
+
+static int si4455_get_response(struct uart_port *port,
+ int length,
+ u8 *data);
+static int si4455_send_command(struct uart_port *port,
+ int length,
+ u8 *data);
+static int si4455_send_command_get_response(struct uart_port *port,
+ int outLength,
+ u8 *outData,
+ int inLength,
+ u8 *inData);
+static int si4455_read_data(struct uart_port *port,
+ u8 command,
+ int pollCts,
+ int length,
+ u8 *data);
+static int si4455_write_data(struct uart_port *port,
+ u8 command,
+ int pollCts,
+ int length,
+ u8 *data);
+static int si4455_poll_cts(struct uart_port *port);
+static void si4455_set_power(struct si4455_port *priv,
+ int on);
+static int si4455_get_part_info(struct uart_port *port,
+ struct si4455_part_info *result);
+
+static int si4455_get_response(struct uart_port *port,
+ int length,
+ u8 *data)
+{
+ int ret = -EIO;
+ u8 dataOut[] = { SI4455_CMD_ID_READ_CMD_BUFF };
+ u8 *dataIn = devm_kzalloc(port->dev, 1 + length, GFP_KERNEL);
+ struct spi_transfer xfer[] = {
+ {
+ .tx_buf = dataOut,
+ .len = sizeof(dataOut),
+ }, {
+ .rx_buf = dataIn,
+ .len = 1 + length,
+ }
+ };
+ int errCnt = 10000;
+
+ while (errCnt > 0) {
+ dataOut[0] = SI4455_CMD_ID_READ_CMD_BUFF;
+ ret = spi_sync_transfer(to_spi_device(port->dev),
+ xfer,
+ ARRAY_SIZE(xfer));
+ if (ret == 0) {
+ if (dataIn[0] == 0xFF) {
+ if ((length > 0) && (data != NULL)) {
+ memcpy(data, &dataIn[1], length);
+ } else {
+ if (length > 0)
+ ret = -EINVAL;
+ }
+ break;
+ }
+ usleep_range(100, 200);
+ } else {
+ break;
+ }
+ errCnt--;
+ }
+ if (errCnt == 0) {
+ dev_err(port->dev, "si4455_poll_cts:errCnt==%i", errCnt);
+ ret = -EIO;
+ }
+ if (dataIn != NULL)
+ devm_kfree(port->dev, dataIn);
+ return ret;
+}
+
+static int si4455_send_command(struct uart_port *port,
+ int length,
+ u8 *data)
+{
+ int ret;
+
+ ret = si4455_poll_cts(port);
+ if (ret == 0) {
+ ret = spi_write(to_spi_device(port->dev), data, length);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: spi_write error(%i)",
+ __func__,
+ ret);
+ }
+ } else {
+ dev_err(port->dev,
+ "%s: si4455_poll_cts error(%i)",
+ __func__,
+ ret);
+ }
+ return ret;
+}
+
+static int si4455_send_command_get_response(struct uart_port *port,
+ int outLength,
+ u8 *outData,
+ int inLength,
+ u8 *inData)
+{
+ int ret;
+
+ ret = si4455_send_command(port, outLength, outData);
+ if (!ret) {
+ ret = si4455_get_response(port, inLength, inData);
+ } else {
+ dev_err(port->dev,
+ "%s: si4455_send_command error(%i)",
+ __func__,
+ ret);
+ }
+ return ret;
+}
+
+static int si4455_read_data(struct uart_port *port,
+ u8 command,
+ int pollCts,
+ int length,
+ u8 *data)
+{
+ int ret = 0;
+ u8 dataOut[] = { command };
+ struct spi_transfer xfer[] = {
+ {
+ .tx_buf = dataOut,
+ .len = sizeof(dataOut),
+ }, {
+ .rx_buf = data,
+ .len = length,
+ }
+ };
+
+ if (pollCts)
+ ret = si4455_poll_cts(port);
+
+ if (ret == 0) {
+ ret = spi_sync_transfer(to_spi_device(port->dev),
+ xfer,
+ ARRAY_SIZE(xfer));
+ if (ret) {
+ dev_err(port->dev,
+ "%s: spi_sync_transfer error(%i)",
+ __func__,
+ ret);
+ }
+ }
+ return ret;
+}
+
+static int si4455_write_data(struct uart_port *port,
+ u8 command,
+ int pollCts,
+ int length,
+ u8 *data)
+{
+ int ret = 0;
+ u8 *dataOut = NULL;
+
+ if (pollCts)
+ ret = si4455_poll_cts(port);
+
+ if (ret == 0) {
+ dataOut = devm_kzalloc(port->dev, 1 + length, GFP_KERNEL);
+ if (dataOut != NULL) {
+ dataOut[0] = command;
+ memcpy(&dataOut[1], data, length);
+ ret = spi_write(to_spi_device(port->dev),
+ dataOut,
+ 1 + length);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: spi_write error(%i)",
+ __func__,
+ ret);
+ }
+ } else {
+ dev_err(port->dev,
+ "%s: devm_kzalloc error",
+ __func__);
+ ret = -ENOMEM;
+ }
+ }
+ if (dataOut != NULL)
+ devm_kfree(port->dev, dataOut);
+
+ return ret;
+}
+
+static int si4455_poll_cts(struct uart_port *port)
+{
+ return si4455_get_response(port, 0, NULL);
+}
+
+static void si4455_set_power(struct si4455_port *priv,
+ int on)
+{
+ if (priv->shdn_gpio) {
+ if (on) {
+ gpiod_direction_output(priv->shdn_gpio, 0);
+ usleep_range(4000, 5000);
+ gpiod_set_value(priv->shdn_gpio, 1);
+ usleep_range(4000, 5000);
+ } else {
+ gpiod_direction_output(priv->shdn_gpio, 0);
+ }
+ }
+}
+
+static int si4455_s_power(struct device *dev,
+ int on)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ dev_dbg(dev, "%s(on=%d)\n", __func__, on);
+ if (s->power_count == !on)
+ si4455_set_power(s, on);
+ s->power_count += on ? 1 : -1;
+ WARN_ON(s->power_count < 0);
+
+ return 0;
+}
+
+static int si4455_get_part_info(struct uart_port *port,
+ struct si4455_part_info *result)
+{
+ int ret;
+ u8 dataOut[] = { SI4455_CMD_ID_PART_INFO };
+ u8 dataIn[SI4455_CMD_REPLY_COUNT_PART_INFO];
+
+ ret = si4455_send_command_get_response(port,
+ sizeof(dataOut),
+ dataOut,
+ sizeof(dataIn),
+ dataIn);
+ if (ret == 0) {
+ result->CHIPREV = dataIn[0];
+ memcpy(&result->PART, &dataIn[1], sizeof(result->PART));
+ result->PBUILD = dataIn[3];
+ memcpy(&result->ID, &dataIn[4], sizeof(result->ID));
+ result->CUSTOMER = dataIn[6];
+ result->ROMID = dataIn[7];
+ result->BOND = dataIn[8];
+ } else {
+ dev_err(port->dev,
+ "%s: si4455_send_command_get_response error(%i)",
+ __func__,
+ ret);
+ }
+ return ret;
+}
+
+static int si4455_get_int_status(struct uart_port *port,
+ u8 phClear,
+ u8 modemClear,
+ u8 chipClear,
+ struct si4455_int_status *result)
+{
+ int ret;
+ u8 dataOut[] = {
+ SI4455_CMD_ID_GET_INT_STATUS,
+ phClear,
+ modemClear,
+ chipClear
+ };
+ u8 dataIn[SI4455_CMD_REPLY_COUNT_GET_INT_STATUS];
+
+ ret = si4455_send_command_get_response(port,
+ sizeof(dataOut),
+ dataOut,
+ sizeof(dataIn),
+ dataIn);
+ if (ret == 0) {
+ result->INT_PEND = dataIn[0];
+ result->INT_STATUS = dataIn[1];
+ result->PH_PEND = dataIn[2];
+ result->PH_STATUS = dataIn[3];
+ result->MODEM_PEND = dataIn[4];
+ result->MODEM_STATUS = dataIn[5];
+ result->CHIP_PEND = dataIn[6];
+ result->CHIP_STATUS = dataIn[7];
+ } else {
+ dev_err(port->dev,
+ "%s: si4455_send_command_get_response error(%i)",
+ __func__,
+ ret);
+ }
+ return ret;
+}
+
+static int si4455_get_modem_status(struct uart_port *port,
+ u8 modemClear,
+ struct si4455_modem_status *result)
+{
+ int ret;
+ u8 dataOut[] = {
+ SI4455_CMD_ID_GET_MODEM_STATUS,
+ modemClear,
+ };
+ u8 dataIn[SI4455_CMD_REPLY_COUNT_GET_MODEM_STATUS];
+
+ ret = si4455_send_command_get_response(port,
+ sizeof(dataOut),
+ dataOut,
+ sizeof(dataIn),
+ dataIn);
+ if (ret == 0) {
+ result->MODEM_PEND = dataIn[0];
+ result->MODEM_STATUS = dataIn[1];
+ result->CURR_RSSI = dataIn[2];
+ result->LATCH_RSSI = dataIn[3];
+ result->ANT1_RSSI = dataIn[4];
+ result->ANT2_RSSI = dataIn[5];
+ memcpy(&result->AFC_FREQ_OFFSET,
+ &dataIn[6],
+ sizeof(result->AFC_FREQ_OFFSET));
+ } else {
+ dev_err(port->dev,
+ "%s: si4455_send_command_get_response error(%i)",
+ __func__,
+ ret);
+ }
+ return ret;
+}
+
+static int si4455_fifo_info(struct uart_port *port,
+ u8 fifo,
+ struct si4455_fifo_info *result)
+{
+ int ret = 0;
+ u8 dataOut[SI4455_CMD_ARG_COUNT_FIFO_INFO] = {
+ SI4455_CMD_ID_FIFO_INFO, fifo
+ };
+ u8 dataIn[SI4455_CMD_REPLY_COUNT_FIFO_INFO] = { 0 };
+
+ ret = si4455_send_command_get_response(port,
+ sizeof(dataOut),
+ dataOut,
+ sizeof(dataIn),
+ dataIn);
+ if (ret == 0) {
+ result->RX_FIFO_COUNT = dataIn[0];
+ result->TX_FIFO_SPACE = dataIn[1];
+ } else {
+ dev_err(port->dev,
+ "%s: si4455_send_command_get_response error(%i)",
+ __func__,
+ ret);
+ }
+ return ret;
+}
+
+static int si4455_read_rx_fifo(struct uart_port *port,
+ int length,
+ u8 *data)
+{
+ return si4455_read_data(port,
+ SI4455_CMD_ID_READ_RX_FIFO,
+ 0,
+ length,
+ data);
+}
+
+static int si4455_write_tx_fifo(struct uart_port *port,
+ int length,
+ u8 *data)
+{
+ return si4455_write_data(port,
+ SI4455_CMD_ID_WRITE_TX_FIFO,
+ 0,
+ length,
+ data);
+}
+
+static int si4455_rx(struct uart_port *port,
+ u32 channel,
+ u8 condition,
+ u16 length,
+ u8 nextState1,
+ u8 nextState2,
+ u8 nextState3)
+{
+ u8 dataOut[SI4455_CMD_ARG_COUNT_START_RX];
+
+ dataOut[0] = SI4455_CMD_ID_START_RX;
+ dataOut[1] = channel;
+ dataOut[2] = condition;
+ dataOut[3] = (u8)(length >> 8);
+ dataOut[4] = (u8)(length);
+ dataOut[5] = nextState1;
+ dataOut[6] = nextState2;
+ dataOut[7] = nextState3;
+
+ return si4455_send_command(port,
+ SI4455_CMD_ARG_COUNT_START_RX,
+ dataOut);
+}
+
+static int si4455_tx(struct uart_port *port,
+ u8 channel,
+ u8 condition,
+ u16 length)
+{
+ u8 dataOut[/*6*/ SI4455_CMD_ARG_COUNT_START_TX];
+
+ dataOut[0] = SI4455_CMD_ID_START_TX;
+ dataOut[1] = channel;
+ dataOut[2] = condition;
+ dataOut[3] = (u8)(length >> 8);
+ dataOut[4] = (u8)(length);
+ /*TODO: radioCmd[5] = 0x44; in case of rev c2a*/
+
+ return si4455_send_command(port,
+ /*6*/ SI4455_CMD_ARG_COUNT_START_TX,
+ dataOut);
+}
+
+static int si4455_change_state(struct uart_port *port,
+ u8 nextState1)
+{
+ u8 dataOut[SI4455_CMD_ARG_COUNT_CHANGE_STATE];
+
+ dataOut[0] = SI4455_CMD_ID_CHANGE_STATE;
+ dataOut[1] = (u8)nextState1;
+
+ return si4455_send_command(port,
+ SI4455_CMD_ARG_COUNT_CHANGE_STATE,
+ dataOut);
+}
+
+static int si4455_begin_tx(struct uart_port *port,
+ u32 channel,
+ int length,
+ u8 *data)
+{
+ int ret = 0;
+ struct si4455_int_status intStatus = { 0 };
+ struct si4455_fifo_info fifoInfo = { 0 };
+
+ dev_dbg(port->dev, "%s(%u, %u)", __func__, channel, length);
+ if ((length > SI4455_FIFO_SIZE) || (length < 0))
+ ret = -EINVAL;
+
+ if (ret == 0) {
+ ret = si4455_change_state(port,
+ SI4455_CMD_CHANGE_STATE_ARG_NEW_STATE_ENUM_READY);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_change_state error(%i)",
+ __func__,
+ ret);
+ goto end;
+ }
+ ret = si4455_get_int_status(port, 0, 0, 0, &intStatus);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_get_int_status error(%i)",
+ __func__,
+ ret);
+ goto end;
+ }
+ ret = si4455_fifo_info(port,
+ SI4455_CMD_FIFO_INFO_ARG_TX_BIT,
+ &fifoInfo);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_fifo_info error(%i)",
+ __func__,
+ ret);
+ goto end;
+ }
+ ret = si4455_write_tx_fifo(port, (u16)length, data);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_write_tx_fifo error(%i)",
+ __func__,
+ ret);
+ goto end;
+ }
+ ret = si4455_tx(port,
+ (u8)channel,
+ 0x30,
+ (u16)length);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_tx error(%i)",
+ __func__,
+ ret);
+ goto end;
+ }
+ }
+end:
+ return ret;
+}
+
+static int si4455_end_tx(struct uart_port *port)
+{
+ int ret = 0;
+ struct si4455_int_status intStatus = { 0 };
+
+ ret = si4455_change_state(port,
+ SI4455_CMD_CHANGE_STATE_ARG_NEW_STATE_ENUM_READY);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_change_state error(%i)",
+ __func__,
+ ret);
+ goto end;
+ }
+ ret = si4455_get_int_status(port, 0, 0, 0, &intStatus);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_get_int_status error(%i)",
+ __func__,
+ ret);
+ goto end;
+ }
+end:
+ return ret;
+}
+
+static int si4455_begin_rx(struct uart_port *port,
+ u32 channel,
+ u32 length)
+{
+ int ret = 0;
+ struct si4455_int_status intStatus = { 0 };
+ struct si4455_fifo_info fifoInfo = { 0 };
+
+ dev_dbg(port->dev, "%s(%u, %u)", __func__, channel, length);
+ ret = si4455_get_int_status(port, 0, 0, 0, &intStatus);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_get_int_status error(%i)",
+ __func__,
+ ret);
+ goto end;
+ }
+ ret = si4455_fifo_info(port,
+ SI4455_CMD_FIFO_INFO_ARG_RX_BIT,
+ &fifoInfo);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_fifo_info error(%i)",
+ __func__,
+ ret);
+ goto end;
+ }
+ ret = si4455_rx(port,
+ channel,
+ 0x00,
+ length,
+ SI4455_CMD_START_RX_ARG_RXTIMEOUT_STATE_ENUM_RX,
+ SI4455_CMD_START_RX_ARG_RXVALID_STATE_ENUM_RX,
+ SI4455_CMD_START_RX_ARG_RXINVALID_STATE_ENUM_RX);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_rx error(%i)",
+ __func__,
+ ret);
+ goto end;
+ }
+end:
+ return ret;
+}
+
+static int si4455_end_rx(struct uart_port *port,
+ u32 length,
+ u8 *data)
+{
+ return si4455_read_rx_fifo(port, length, data);
+}
+
+static int si4455_configure(struct uart_port *port,
+ u8 *configurationData)
+{
+ int ret = 0;
+ u8 col;
+ u8 response;
+ u8 numOfBytes;
+ struct si4455_int_status intStatus = { 0 };
+ u8 radioCmd[16u];
+
+ /* While cycle as far as the pointer points to a command */
+ while (*configurationData != 0x00) {
+ /* Commands structure in the array:
+ * --------------------------------
+ * LEN | <LEN length of data>
+ */
+ numOfBytes = *configurationData++;
+ dev_dbg(port->dev,
+ "%s: numOfBytes(%u)",
+ __func__,
+ numOfBytes);
+ if (numOfBytes > 16u) {
+ /* Initial configuration of Si4x55 */
+ if (SI4455_CMD_ID_WRITE_TX_FIFO
+ == *configurationData) {
+ if (numOfBytes > 128u) {
+ /* Number of command bytes exceeds
+ * maximal allowable length
+ */
+ dev_err(port->dev,
+ "%s: command length error(%i)",
+ __func__,
+ numOfBytes);
+ ret = -EINVAL;
+ break;
+ }
+
+ /* Load array to the device */
+ configurationData++;
+ ret = si4455_write_data(port,
+ SI4455_CMD_ID_WRITE_TX_FIFO,
+ 1,
+ numOfBytes - 1,
+ configurationData);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_write_data error(%i)",
+ __func__,
+ ret);
+ break;
+ }
+
+ /* Point to the next command */
+ configurationData += numOfBytes - 1;
+
+ /* Continue command interpreter */
+ continue;
+ } else {
+ /* Number of command bytes exceeds
+ * maximal allowable length
+ */
+ ret = -EINVAL;
+ break;
+ }
+ }
+
+ for (col = 0u; col < numOfBytes; col++) {
+ radioCmd[col] = *configurationData;
+ configurationData++;
+ }
+
+ dev_dbg(port->dev,
+ "%s: radioCmd[0](%u)",
+ __func__,
+ radioCmd[0]);
+ ret = si4455_send_command_get_response(port,
+ numOfBytes,
+ radioCmd,
+ 1,
+ &response);
+ if (ret) {
+ dev_err(port->dev,
+ "%s: si4455_send_command_get_response error(%i)",
+ __func__,
+ ret);
+ break;
+ }
+
+ /* Check response byte of EZCONFIG_CHECK command */
+ if (radioCmd[0] == SI4455_CMD_ID_EZCONFIG_CHECK) {
+ if (response) {
+ /* Number of command bytes exceeds
+ * maximal allowable length
+ */
+ ret = -EIO;
+ dev_err(port->dev,
+ "%s: EZConfig check error(%i)",
+ __func__,
+ radioCmd[0]);
+ break;
+ }
+ }
+
+ /* Get and clear all interrupts. An error has occurred... */
+ si4455_get_int_status(port, 0, 0, 0, &intStatus);
+ if (intStatus.CHIP_PEND
+ & SI4455_CMD_GET_CHIP_STATUS_REP_CMD_ERROR_PEND_MASK) {
+ ret = -EIO;
+ dev_err(port->dev,
+ "%s: chip error(%i)",
+ __func__,
+ intStatus.CHIP_PEND);
+ break;
+ }
+ }
+
+ return ret;
+}
+
+static int si4455_re_configure(struct uart_port *port)
+{
+ int ret = 0;
+ struct si4455_port *s = dev_get_drvdata(port->dev);
+
+ mutex_lock(&s->mutex);
+ s->configured = 0;
+ if (s->power_count > 0)
+ si4455_s_power(port->dev, 0);
+
+ si4455_s_power(port->dev, 1);
+ if (s->configuration.length > 0) {
+ ret = si4455_configure(port, s->configuration.data);
+ if (ret == 0)
+ s->configured = 1;
+
+ }
+ mutex_unlock(&s->mutex);
+ return ret;
+}
+
+static int si4455_do_work(struct uart_port *port)
+{
+ int ret = 0;
+ struct si4455_port *s = dev_get_drvdata(port->dev);
+ struct circ_buf *xmit = &port->state->xmit;
+ unsigned int tx_pending = 0;
+ unsigned int tx_to_end = 0;
+ u8 *data = NULL;
+
+ mutex_lock(&s->mutex);
+ if (s->configured && (s->power_count > 0)) {
+ if (!(uart_circ_empty(xmit)
+ || uart_tx_stopped(port)
+ || s->tx_pending)) {
+ tx_pending = uart_circ_chars_pending(xmit);
+ if (s->package_size > 0) {
+ if (tx_pending >= s->package_size) {
+ tx_pending = s->package_size;
+ data = devm_kzalloc(port->dev,
+ s->package_size,
+ GFP_KERNEL);
+ tx_to_end = CIRC_CNT_TO_END(xmit->head,
+ xmit->tail,
+ UART_XMIT_SIZE);
+ if (tx_to_end < tx_pending) {
+ memcpy(data,
+ xmit->buf + xmit->tail,
+ tx_to_end);
+ memcpy(data,
+ xmit->buf,
+ tx_pending - tx_to_end);
+ } else {
+ memcpy(data,
+ xmit->buf + xmit->tail,
+ tx_pending);
+ }
+ if (si4455_begin_tx(port,
+ s->tx_channel,
+ tx_pending,
+ data) == 0) {
+ s->tx_pending = true;
+ }
+ devm_kfree(port->dev, data);
+ }
+ } else {
+ //TODO: variable packet length
+ }
+ }
+ if (!s->tx_pending) {
+ if (s->package_size > 0) {
+ ret = si4455_begin_rx(port,
+ s->rx_channel,
+ s->package_size);
+ } else {
+ //TODO: variable packet length
+ }
+ }
+ }
+ mutex_unlock(&s->mutex);
+ return ret;
+}
+
+static void si4455_handle_rx_pend(struct si4455_port *s)
+{
+ struct uart_port *port = &s->one.port;
+ u8 *data = NULL;
+ int sret = 0;
+ int i = 0;
+
+ if (s->package_size > 0) {
+ data = devm_kzalloc(port->dev,
+ s->package_size,
+ GFP_KERNEL);
+ sret = si4455_end_rx(port,
+ s->package_size,
+ data);
+ if (sret == 0) {
+ for (i = 0; i < s->package_size; i++) {
+ uart_insert_char(port,
+ 0,
+ 0,
+ data[i],
+ TTY_NORMAL);
+ port->icount.rx++;
+ }
+ tty_flip_buffer_push(&port->state->port);
+ } else {
+ dev_err(port->dev,
+ "%s: si4455_end_rx error(%i)",
+ __func__,
+ sret);
+ }
+ devm_kfree(port->dev, data);
+ } else {
+ //TODO: variable packet length
+ }
+}
+
+static void si4455_handle_tx_pend(struct si4455_port *s)
+{
+ struct uart_port *port = &s->one.port;
+ struct circ_buf *xmit = &port->state->xmit;
+
+ if (s->tx_pending) {
+ if (s->package_size) {
+ port->icount.tx += s->package_size;
+ xmit->tail = (xmit->tail + s->package_size)
+ & (UART_XMIT_SIZE - 1);
+ } else {
+ //TODO: variable packet length
+ }
+ si4455_end_tx(port);
+ s->tx_pending = 0;
+ }
+}
+
+static irqreturn_t si4455_port_irq(struct si4455_port *s)
+{
+ struct uart_port *port = &s->one.port;
+ irqreturn_t ret = IRQ_NONE;
+ struct si4455_int_status intStatus = { 0 };
+ struct si4455_fifo_info fifoInfo = { 0 };
+
+ mutex_lock(&s->mutex);
+ if (s->configured && (s->power_count > 0)) {
+ if (!si4455_get_int_status(port, 0, 0, 0, &intStatus)) {
+ si4455_get_modem_status(port, 0, &s->modem_status);
+ if (intStatus.CHIP_PEND
+ & SI4455_CMD_GET_CHIP_STATUS_REP_CMD_ERROR_PEND_BIT) {
+ dev_err(port->dev,
+ "%s: CHIP_STATUS:CMD_ERROR_PEND",
+ __func__);
+ } else if (intStatus.PH_PEND
+ & SI4455_CMD_GET_INT_STATUS_REP_PACKET_SENT_PEND_BIT) {
+ dev_dbg(port->dev,
+ "%s: PH_STATUS:PACKET_SENT_PEND",
+ __func__);
+ si4455_handle_tx_pend(s);
+ } else if (intStatus.PH_PEND
+ & SI4455_CMD_GET_INT_STATUS_REP_PACKET_RX_PEND_BIT) {
+ dev_dbg(port->dev,
+ "%s: PH_STATUS:PACKET_RX_PEND",
+ __func__);
+ s->current_rssi = s->modem_status.CURR_RSSI;
+ si4455_fifo_info(port, 0, &fifoInfo);
+ si4455_handle_rx_pend(s);
+ } else if (intStatus.PH_PEND
+ & SI4455_CMD_GET_INT_STATUS_REP_CRC_ERROR_BIT) {
+ dev_dbg(port->dev,
+ "%s: PH_STATUS:CRC_ERROR_PEND",
+ __func__);
+ }
+ ret = IRQ_HANDLED;
+ }
+ } else {
+ ret = IRQ_HANDLED;
+ }
+ mutex_unlock(&s->mutex);
+ si4455_do_work(port);
+ return ret;
+}
+
+static irqreturn_t si4455_ist(int irq,
+ void *dev_id)
+{
+ struct si4455_port *s = (struct si4455_port *)dev_id;
+ bool handled = false;
+
+ if (si4455_port_irq(s) == IRQ_HANDLED)
+ handled = true;
+
+ return IRQ_RETVAL(handled);
+}
+
+static void si4455_tx_proc(struct work_struct *ws)
+{
+ struct si4455_one *one = container_of(ws,
+ struct si4455_one,
+ tx_work);
+
+ si4455_do_work(&one->port);
+}
+
+static unsigned int si4455_tx_empty(struct uart_port *port)
+{
+ return TIOCSER_TEMT;
+}
+
+static unsigned int si4455_get_mctrl(struct uart_port *port)
+{
+ dev_dbg(port->dev, "%s", __func__);
+ return TIOCM_DSR | TIOCM_CAR;
+}
+
+static void si4455_set_mctrl(struct uart_port *port,
+ unsigned int mctrl)
+{
+ dev_dbg(port->dev, "%s", __func__);
+}
+
+static void si4455_break_ctl(struct uart_port *port,
+ int break_state)
+{
+ dev_dbg(port->dev, "%s", __func__);
+}
+
+static void si4455_set_termios(struct uart_port *port,
+ struct ktermios *termios,
+ struct ktermios *old)
+{
+ dev_dbg(port->dev, "%s", __func__);
+}
+
+static int si4455_rs485_config(struct uart_port *port,
+ struct serial_rs485 *rs485)
+{
+ dev_dbg(port->dev, "%s", __func__);
+
+ return 0;
+}
+
+static int si4455_startup(struct uart_port *port)
+{
+ dev_dbg(port->dev, "%s", __func__);
+ si4455_s_power(port->dev, 1);
+ return 0;
+}
+
+static void si4455_shutdown(struct uart_port *port)
+{
+ dev_dbg(port->dev, "%s", __func__);
+ si4455_s_power(port->dev, 0);
+}
+
+static const char *si4455_type(struct uart_port *port)
+{
+ struct si4455_port *s = dev_get_drvdata(port->dev);
+
+ if (port->type == PORT_SI4455) {
+ if (s->part_info.ROMID == 3)
+ return "SI4455-B1A";
+ else if (s->part_info.ROMID == 6)
+ return "SI4455-C2A";
+
+ }
+ return NULL;
+}
+
+static int si4455_request_port(struct uart_port *port)
+{
+ /* Do nothing */
+ dev_dbg(port->dev, "%s", __func__);
+ return 0;
+}
+
+static void si4455_config_port(struct uart_port *port,
+ int flags)
+{
+ dev_dbg(port->dev, "%s", __func__);
+ if (flags & UART_CONFIG_TYPE)
+ port->type = PORT_SI4455;
+}
+
+static int si4455_verify_port(struct uart_port *port,
+ struct serial_struct *s)
+{
+ if ((s->type != PORT_UNKNOWN) && (s->type != PORT_SI4455))
+ return -EINVAL;
+
+ if (s->irq != port->irq)
+ return -EINVAL;
+
+ return 0;
+}
+
+static void si4455_start_tx(struct uart_port *port)
+{
+ struct si4455_one *one = container_of(port,
+ struct si4455_one,
+ port);
+
+ dev_dbg(port->dev, "%s", __func__);
+
+ if (!work_pending(&one->tx_work))
+ schedule_work(&one->tx_work);
+
+}
+
+static int si4455_ioctl(struct uart_port *port,
+ unsigned int cmd,
+ unsigned long arg)
+{
+ struct si4455_port *s = dev_get_drvdata(port->dev);
+ int ret = 0;
+
+ dev_dbg(port->dev, "%s(%u)", __func__, cmd);
+ switch (cmd) {
+ case SI4455_IOC_SEZC:
+ memcpy(&s->configuration, (void *)arg, sizeof(s->configuration));
+ dev_dbg(port->dev,
+ "%s(%u): SI4455_IOC_SEZC, length(%i)",
+ __func__,
+ cmd,
+ s->configuration.length);
+ ret = si4455_re_configure(port);
+ break;
+ case SI4455_IOC_CEZC:
+ dev_dbg(port->dev,
+ "%s(%u): SI4455_IOC_CEZC",
+ __func__,
+ cmd);
+ memset(&s->configuration, 0x00, sizeof(s->configuration));
+ ret = si4455_re_configure(port);
+ break;
+ case SI4455_IOC_SEZP:
+ memcpy(&s->patch, (void *)arg, sizeof(s->patch));
+ dev_dbg(port->dev,
+ "%s(%u): SI4455_IOC_SEZP, length(%i)",
+ __func__,
+ cmd,
+ s->configuration.length);
+ break;
+ case SI4455_IOC_CEZP:
+ dev_dbg(port->dev,
+ "%s(%u): SI4455_IOC_CEZP",
+ __func__,
+ cmd);
+ memset(&s->patch, 0x00, sizeof(s->patch));
+ break;
+ case SI4455_IOC_STXC:
+ s->tx_channel = *((u32 *)arg);
+ dev_dbg(port->dev,
+ "%s(%u): SI4455_IOC_STXC, tx_channel(%i)",
+ __func__,
+ cmd,
+ s->tx_channel);
+ break;
+ case SI4455_IOC_GTXC:
+ dev_dbg(port->dev,
+ "%s(%u): SI4455_IOC_GTXC",
+ __func__,
+ cmd);
+ *((u32 *)arg) = s->tx_channel;
+ break;
+ case SI4455_IOC_SRXC:
+ s->rx_channel = *((u32 *)arg);
+ dev_dbg(port->dev,
+ "%s(%u): SI4455_IOC_SRXC, rx_channel(%i)",
+ __func__,
+ cmd,
+ s->rx_channel);
+ break;
+ case SI4455_IOC_GRXC:
+ dev_dbg(port->dev,
+ "%s(%u): SI4455_IOC_GRXC",
+ __func__,
+ cmd);
+ *((u32 *)arg) = s->rx_channel;
+ break;
+ case SI4455_IOC_SSIZ:
+ s->package_size = *((u32 *)arg);
+ dev_dbg(port->dev,
+ "%s(%u): SI4455_IOC_SSIZ, package_size(%i)",
+ __func__,
+ cmd,
+ s->package_size);
+ break;
+ case SI4455_IOC_GSIZ:
+ dev_dbg(port->dev,
+ "%s(%u): SI4455_IOC_GSIZ",
+ __func__,
+ cmd);
+ *((u32 *)arg) = s->package_size;
+ break;
+ case SI4455_IOC_GRSSI:
+ dev_dbg(port->dev,
+ "%s(%u): SI4455_IOC_GRSSI",
+ __func__,
+ cmd);
+ *((u32 *)arg) = s->current_rssi;
+ break;
+ default:
+ ret = -ENOIOCTLCMD;
+ break;
+ }
+
+ if (ret == 0)
+ si4455_do_work(port);
+
+ return ret;
+}
+
+
+static void si4455_null_void(struct uart_port *port)
+{
+ /* Do nothing */
+}
+
+static const struct uart_ops si4455_ops = {
+ .tx_empty = si4455_tx_empty,
+ .set_mctrl = si4455_set_mctrl,
+ .get_mctrl = si4455_get_mctrl,
+ .stop_tx = si4455_null_void,
+ .start_tx = si4455_start_tx,
+ .stop_rx = si4455_null_void,
+ .break_ctl = si4455_break_ctl,
+ .startup = si4455_startup,
+ .shutdown = si4455_shutdown,
+ .set_termios = si4455_set_termios,
+ .type = si4455_type,
+ .request_port = si4455_request_port,
+ .release_port = si4455_null_void,
+ .config_port = si4455_config_port,
+ .verify_port = si4455_verify_port,
+ .ioctl = si4455_ioctl,
+};
+
+static int __maybe_unused si4455_suspend(struct device *dev)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ uart_suspend_port(&si4455_uart, &s->one.port);
+ return 0;
+}
+
+static int __maybe_unused si4455_resume(struct device *dev)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ uart_resume_port(&si4455_uart, &s->one.port);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(si4455_pm_ops, si4455_suspend, si4455_resume);
+
+static int si4455_probe(struct device *dev,
+ int irq)
+{
+ int ret;
+ struct si4455_port *s;
+
+ /* Alloc port structure */
+ dev_dbg(dev, "%s\n", __func__);
+ s = devm_kzalloc(dev, sizeof(*s), GFP_KERNEL);
+ if (!s) {
+ dev_err(dev, "Error allocating port structure\n");
+ return -ENOMEM;
+ }
+
+ dev_set_drvdata(dev, s);
+ mutex_init(&s->mutex);
+
+ s->shdn_gpio = devm_gpiod_get(dev, "shdn", GPIOD_OUT_HIGH);
+ if (IS_ERR(s->shdn_gpio)) {
+ dev_err(dev, "Unable to reguest shdn gpio\n");
+ ret = -EINVAL;
+ goto out_generic;
+ }
+
+ /* Initialize port data */
+ s->one.port.dev = dev;
+ s->one.port.line = 0;
+ s->one.port.irq = irq;
+ s->one.port.type = PORT_SI4455;
+ s->one.port.fifosize = SI4455_FIFO_SIZE;
+ s->one.port.flags = UPF_FIXED_TYPE | UPF_LOW_LATENCY;
+ s->one.port.iotype = UPIO_PORT;
+ s->one.port.iobase = 0x00;
+ s->one.port.membase = (void __iomem *)~0;
+ s->one.port.rs485_config = si4455_rs485_config;
+ s->one.port.ops = &si4455_ops;
+
+ si4455_s_power(dev, 1);
+
+ //detect
+ ret = si4455_get_part_info(&s->one.port, &s->part_info);
+ dev_dbg(dev, "si4455_get_part_info()==%i", ret);
+ if (ret == 0) {
+ dev_dbg(dev, "partInfo.CHIPREV= %u", s->part_info.CHIPREV);
+ dev_dbg(dev, "partInfo.PART= %u", s->part_info.PART);
+ dev_dbg(dev, "partInfo.PBUILD= %u", s->part_info.PBUILD);
+ dev_dbg(dev, "partInfo.ID= %u", s->part_info.ID);
+ dev_dbg(dev, "partInfo.CUSTOMER= %u", s->part_info.CUSTOMER);
+ dev_dbg(dev, "partInfo.ROMID= %u", s->part_info.ROMID);
+ dev_dbg(dev, "partInfo.BOND= %u", s->part_info.BOND);
+ if (s->part_info.PART != 0x5544) {
+ dev_err(dev, "PART(%u) error", s->part_info.PART);
+ ret = -ENODEV;
+ }
+ }
+ si4455_s_power(dev, 0);
+ if (ret)
+ goto out_generic;
+
+ /* Initialize queue for start TX */
+ INIT_WORK(&s->one.tx_work, si4455_tx_proc);
+
+ /* Register port */
+ ret = uart_add_one_port(&si4455_uart, &s->one.port);
+ if (ret) {
+ s->one.port.dev = NULL;
+ goto out_uart;
+ }
+
+ /* Setup interrupt */
+ ret = devm_request_threaded_irq(dev,
+ irq,
+ NULL,
+ si4455_ist,
+ IRQF_ONESHOT | IRQF_SHARED,
+ dev_name(dev),
+ s);
+ if (!ret)
+ return 0;
+
+ dev_err(dev, "Unable to reguest IRQ %i\n", irq);
+
+out_uart:
+ uart_remove_one_port(&si4455_uart, &s->one.port);
+out_generic:
+ mutex_destroy(&s->mutex);
+
+ return ret;
+}
+
+static int si4455_remove(struct device *dev)
+{
+ struct si4455_port *s = dev_get_drvdata(dev);
+
+ cancel_work_sync(&s->one.tx_work);
+ uart_remove_one_port(&si4455_uart, &s->one.port);
+
+ mutex_destroy(&s->mutex);
+
+ return 0;
+}
+
+static const struct of_device_id __maybe_unused si4455_dt_ids[] = {
+ { .compatible = "silabs,si4455" },
+ { .compatible = "silabs,si4455b1a" },
+ { .compatible = "silabs,si4455c2a" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, si4455_dt_ids);
+
+static int si4455_spi_probe(struct spi_device *spi)
+{
+ int ret;
+
+ /* Setup SPI bus */
+ spi->bits_per_word = 8;
+ spi->mode = SPI_MODE_0;
+ spi->max_speed_hz = 100000;
+ ret = spi_setup(spi);
+ if (ret)
+ return ret;
+
+ if (spi->dev.of_node) {
+ const struct of_device_id *of_id
+ = of_match_device(si4455_dt_ids, &spi->dev);
+ if (!of_id)
+ return -ENODEV;
+
+ }
+
+ return si4455_probe(&spi->dev, spi->irq);
+}
+
+static int si4455_spi_remove(struct spi_device *spi)
+{
+ return si4455_remove(&spi->dev);
+}
+
+static const struct spi_device_id si4455_id_table[] = {
+ { "si4455b1a" },
+ { }
+};
+MODULE_DEVICE_TABLE(spi, si4455_id_table);
+
+static struct spi_driver si4455_spi_driver = {
+ .driver = {
+ .name = SI4455_NAME,
+ .of_match_table = of_match_ptr(si4455_dt_ids),
+ .pm = &si4455_pm_ops,
+ },
+ .probe = si4455_spi_probe,
+ .remove = si4455_spi_remove,
+ .id_table = si4455_id_table,
+};
+
+static int __init si4455_uart_init(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&si4455_uart);
+ if (ret)
+ return ret;
+ spi_register_driver(&si4455_spi_driver);
+
+ return 0;
+}
+module_init(si4455_uart_init);
+
+static void __exit si4455_uart_exit(void)
+{
+ spi_unregister_driver(&si4455_spi_driver);
+ uart_unregister_driver(&si4455_uart);
+}
+module_exit(si4455_uart_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("József Horváth <info@xxxxxxxxxxx>");
+MODULE_DESCRIPTION("SI4455 serial driver");
diff --git a/drivers/staging/si4455/si4455_api.h b/drivers/staging/si4455/si4455_api.h
new file mode 100644
index 000000000000..9b046bd006cf
--- /dev/null
+++ b/drivers/staging/si4455/si4455_api.h
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 József Horváth <info@xxxxxxxxxxx>
+ *
+ */
+#ifndef SI4455_API_H_
+#define SI4455_API_H_
+
+struct si4455_iocbuff {
+ uint32_t length;
+ uint8_t data[4096];
+};
+
+#define BASE_TTYIOC_PRIVATE 0xA0
+/* Set EZConfig.
+ * After this ioctl call, the driver restarts the si4455,
+ * then apply the new configuration and patch.
+ */
+#define SI4455_IOC_SEZC _IOW('T', \
+ BASE_TTYIOC_PRIVATE + 0x01, \
+ struct si4455_iocbuff)
+/* Clear driver EZConfig.
+ * After this ioctl call, the driver restarts the si4455,
+ * then apply the new configuration and patch.
+ */
+#define SI4455_IOC_CEZC _IO('T', BASE_TTYIOC_PRIVATE + 0x02)
+/* Set radio patch.
+ * After this ioctl call, the driver restarts the si4455,
+ * then apply the new configuration and patch.
+ * This ioctl code is for future use only. Not implemented yet.
+ */
+#define SI4455_IOC_SEZP _IOW('T', \
+ BASE_TTYIOC_PRIVATE + 0x03, \
+ struct si4455_iocbuff)
+/* Clear radio patch.
+ * After this ioctl call, the driver restarts the si4455,
+ * then apply the new configuration and patch.
+ * This ioctl code is for future use only. Not implemented yet.
+ */
+#define SI4455_IOC_CEZP _IO('T', BASE_TTYIOC_PRIVATE + 0x04)
+/* Get transmit channel. */
+#define SI4455_IOC_GTXC _IOR('T', BASE_TTYIOC_PRIVATE + 0x11, uint32_t)
+/* Set transmit channel. */
+#define SI4455_IOC_STXC _IOW('T', BASE_TTYIOC_PRIVATE + 0x12, uint32_t)
+/* Get receive channel. */
+#define SI4455_IOC_GRXC _IOR('T', BASE_TTYIOC_PRIVATE + 0x13, uint32_t)
+/* Set receive channel. */
+#define SI4455_IOC_SRXC _IOW('T', BASE_TTYIOC_PRIVATE + 0x14, uint32_t)
+/* Get fixed length package size. */
+#define SI4455_IOC_GSIZ _IOR('T', BASE_TTYIOC_PRIVATE + 0x15, uint32_t)
+/* Set fixed length package size. */
+#define SI4455_IOC_SSIZ _IOW('T', BASE_TTYIOC_PRIVATE + 0x16, uint32_t)
+/* Get last rssi value. */
+#define SI4455_IOC_GRSSI _IOR('T', BASE_TTYIOC_PRIVATE + 0x20, uint32_t)
+
+#endif
--
2.17.1