Re: [PATCH v3 0/3] Support wakeup methods of Atmel maXTouch controllers
From: Dmitry Osipenko
Date: Sat Dec 12 2020 - 05:07:45 EST
Hello,
12.12.2020 05:43, Dmitry Torokhov пишет:
> Hi Dmitry,
>
> On Mon, Dec 07, 2020 at 12:22:14AM +0300, Dmitry Osipenko wrote:
>> Some Atmel maXTouch controllers, like mXT1386 and mXT3432S1 for example,
>> have a WAKE line that needs to be asserted in order to wake controller
>> from a deep sleep, otherwise it will be unusable. This series implements
>> support for the wakeup methods in accordance to the mXT1386 datasheet [1],
>> see page 29 (chapter "5.8 WAKE Line").
>>
>> The mXT1386 is a widely used controller found on many older Android tablet
>> devices. Touchscreen on Acer A500 tablet now works properly after this
>> series.
>
> I am trying to understand how your controller is configured on that
> system. Could you please enable all debug messages in the driver and
> post the logs? I am a bit confused why the controller needs to be woken
> up twice in mxt_start() given that according to the spec it is supposed
> to stay up for 2 seconds after successful I2C transfer...
>From the page 30 in the datasheet:
"Note that when the mXT1386 is sent into deep sleep mode, it goes to
sleep immediately. In this case the two-second timeout does not apply
until the WAKE pin is asserted."
The debug log seems confirm that quote:
...
[ 1.196404] Family: 160 Variant: 0 Firmware V1.0.AA Objects: 18
[ 1.196572] T37 Start:118 Size:130 Instances:1 Report IDs:0-0
[ 1.196586] T44 Start:248 Size:1 Instances:1 Report IDs:0-0
[ 1.196597] T5 Start:249 Size:9 Instances:1 Report IDs:0-0
[ 1.196608] T6 Start:258 Size:6 Instances:1 Report IDs:1-1
[ 1.196617] T38 Start:264 Size:64 Instances:1 Report IDs:0-0
[ 1.196628] T7 Start:328 Size:3 Instances:1 Report IDs:0-0
[ 1.196638] T8 Start:331 Size:10 Instances:1 Report IDs:0-0
[ 1.196648] T9 Start:341 Size:34 Instances:1 Report IDs:2-17
[ 1.196658] T15 Start:375 Size:11 Instances:2 Report IDs:18-19
[ 1.196668] T18 Start:397 Size:2 Instances:1 Report IDs:0-0
[ 1.196678] T22 Start:399 Size:17 Instances:1 Report IDs:20-20
[ 1.196688] T24 Start:416 Size:19 Instances:1 Report IDs:21-24
[ 1.196698] T25 Start:435 Size:14 Instances:1 Report IDs:25-25
[ 1.196708] T27 Start:449 Size:7 Instances:1 Report IDs:26-26
[ 1.196718] T28 Start:456 Size:6 Instances:1 Report IDs:27-27
[ 1.196728] T40 Start:462 Size:5 Instances:1 Report IDs:0-0
[ 1.196738] T41 Start:467 Size:6 Instances:1 Report IDs:0-0
[ 1.196748] T43 Start:473 Size:6 Instances:1 Report IDs:0-0
[ 1.196852] Direct firmware load for maxtouch.cfg failed with error -2
[ 1.197305] T6 Config Checksum: 0x8D7459
[ 1.197318] T6 Status 0x90 RESET CAL
[ 1.197543] Initialized power cfg: ACTV 10, IDLE 50
[ 1.198387] Touchscreen size X1279Y799
...
[ 1.211686] T6 Status 0x00 OK
...
[15.576573] Set T7 ACTV:10 IDLE:50
[15.592142] T6 Status 0x10 CAL
[15.597920] T6 Status 0x00 OK
[15.604846] Set T7 ACTV:0 IDLE:0
[15.831477] waking up controller
[15.862912] Set T7 ACTV:10 IDLE:50
[15.872783] Set T7 ACTV:0 IDLE:0
[15.880333] T6 Status 0x10 CAL
[15.946853] Set T7 ACTV:10 IDLE:50
[15.956582] Set T7 ACTV:0 IDLE:0
...
[27.897337] waking up controller
[27.924172] Set T7 ACTV:10 IDLE:50
[27.947286] T6 Status 0x00 OK
[27.959754] Set T7 ACTV:0 IDLE:0
[27.970258] Set T7 ACTV:10 IDLE:50
[27.987546] T6 Status 0x10 CAL
[27.993327] T6 Status 0x00 OK