[PATCH v3 5/5] net: stmmac: dwmac-meson8b: add support for the RGMII RX delay on G12A

From: Martin Blumenstingl
Date: Wed Dec 23 2020 - 18:32:20 EST


Amlogic Meson G12A (and newer: G12B, SM1) SoCs have a more advanced RX
delay logic. Instead of fine-tuning the delay in the nanoseconds range
it now allows tuning in 200 picosecond steps. This support comes with
new bits in the PRG_ETH1[19:16] register.

Add support for validating the RGMII RX delay as well as configuring the
register accordingly on these platforms.

Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
Reviewed-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
---
.../ethernet/stmicro/stmmac/dwmac-meson8b.c | 61 +++++++++++++++----
1 file changed, 48 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
index 4937432ac70d..55152d7ba99a 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
@@ -68,10 +68,21 @@
*/
#define PRG_ETH0_ADJ_SKEW GENMASK(24, 20)

+#define PRG_ETH1 0x4
+
+/* Defined for adding a delay to the input RX_CLK for better timing.
+ * Each step is 200ps. These bits are used with external RGMII PHYs
+ * because RGMII RX only has the small window. cfg_rxclk_dly can
+ * adjust the window between RX_CLK and RX_DATA and improve the stability
+ * of "rx data valid".
+ */
+#define PRG_ETH1_CFG_RXCLK_DLY GENMASK(19, 16)
+
struct meson8b_dwmac;

struct meson8b_dwmac_data {
int (*set_phy_mode)(struct meson8b_dwmac *dwmac);
+ bool has_prg_eth1_rgmii_rx_delay;
};

struct meson8b_dwmac {
@@ -270,30 +281,35 @@ static int meson8b_devm_clk_prepare_enable(struct meson8b_dwmac *dwmac,

static int meson8b_init_rgmii_delays(struct meson8b_dwmac *dwmac)
{
- u32 tx_dly_config, rx_dly_config, delay_config;
+ u32 tx_dly_config, rx_adj_config, cfg_rxclk_dly, delay_config;
int ret;

+ rx_adj_config = 0;
+ cfg_rxclk_dly = 0;
tx_dly_config = FIELD_PREP(PRG_ETH0_TXDLY_MASK,
dwmac->tx_delay_ns >> 1);

- if (dwmac->rx_delay_ps == 2000)
- rx_dly_config = PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP;
- else
- rx_dly_config = 0;
+ if (dwmac->data->has_prg_eth1_rgmii_rx_delay)
+ cfg_rxclk_dly = FIELD_PREP(PRG_ETH1_CFG_RXCLK_DLY,
+ dwmac->rx_delay_ps / 200);
+ else if (dwmac->rx_delay_ps == 2000)
+ rx_adj_config = PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP;

switch (dwmac->phy_mode) {
case PHY_INTERFACE_MODE_RGMII:
- delay_config = tx_dly_config | rx_dly_config;
+ delay_config = tx_dly_config | rx_adj_config;
break;
case PHY_INTERFACE_MODE_RGMII_RXID:
delay_config = tx_dly_config;
+ cfg_rxclk_dly = 0;
break;
case PHY_INTERFACE_MODE_RGMII_TXID:
- delay_config = rx_dly_config;
+ delay_config = rx_adj_config;
break;
case PHY_INTERFACE_MODE_RGMII_ID:
case PHY_INTERFACE_MODE_RMII:
delay_config = 0;
+ cfg_rxclk_dly = 0;
break;
default:
dev_err(dwmac->dev, "unsupported phy-mode %s\n",
@@ -323,6 +339,9 @@ static int meson8b_init_rgmii_delays(struct meson8b_dwmac *dwmac)
PRG_ETH0_ADJ_DELAY | PRG_ETH0_ADJ_SKEW,
delay_config);

+ meson8b_dwmac_mask_bits(dwmac, PRG_ETH1, PRG_ETH1_CFG_RXCLK_DLY,
+ cfg_rxclk_dly);
+
return 0;
}

@@ -423,11 +442,20 @@ static int meson8b_dwmac_probe(struct platform_device *pdev)
dwmac->rx_delay_ps *= 1000;
}

- if (dwmac->rx_delay_ps != 0 && dwmac->rx_delay_ps != 2000) {
- dev_err(&pdev->dev,
- "The only allowed RX delays values are: 0ps, 2000ps");
- ret = -EINVAL;
- goto err_remove_config_dt;
+ if (dwmac->data->has_prg_eth1_rgmii_rx_delay) {
+ if (dwmac->rx_delay_ps != 0 && dwmac->rx_delay_ps != 2000) {
+ dev_err(dwmac->dev,
+ "The only allowed RGMII RX delays values are: 0ps, 2000ps");
+ ret = -EINVAL;
+ goto err_remove_config_dt;
+ }
+ } else {
+ if (dwmac->rx_delay_ps > 3000 || dwmac->rx_delay_ps % 200) {
+ dev_err(dwmac->dev,
+ "The RGMII RX delay range is 0..3000ps in 200ps steps");
+ ret = -EINVAL;
+ goto err_remove_config_dt;
+ }
}

dwmac->timing_adj_clk = devm_clk_get_optional(dwmac->dev,
@@ -469,10 +497,17 @@ static int meson8b_dwmac_probe(struct platform_device *pdev)

static const struct meson8b_dwmac_data meson8b_dwmac_data = {
.set_phy_mode = meson8b_set_phy_mode,
+ .has_prg_eth1_rgmii_rx_delay = false,
};

static const struct meson8b_dwmac_data meson_axg_dwmac_data = {
.set_phy_mode = meson_axg_set_phy_mode,
+ .has_prg_eth1_rgmii_rx_delay = false,
+};
+
+static const struct meson8b_dwmac_data meson_g12a_dwmac_data = {
+ .set_phy_mode = meson_axg_set_phy_mode,
+ .has_prg_eth1_rgmii_rx_delay = true,
};

static const struct of_device_id meson8b_dwmac_match[] = {
@@ -494,7 +529,7 @@ static const struct of_device_id meson8b_dwmac_match[] = {
},
{
.compatible = "amlogic,meson-g12a-dwmac",
- .data = &meson_axg_dwmac_data,
+ .data = &meson_g12a_dwmac_data,
},
{ }
};
--
2.29.2