[PATCH v2 2/2] drm/bridge: anx7625: add MIPI DPI input feature support

From: Xin Ji
Date: Wed Dec 30 2020 - 21:27:22 EST

Add MIPI rx DPI input support

Signed-off-by: Xin Ji <xji@xxxxxxxxxxxxxxxx>
Reported-by: kernel test robot <lkp@xxxxxxxxx>
---
drivers/gpu/drm/bridge/analogix/anx7625.c | 344 ++++++++++++++++++++++++++++--
drivers/gpu/drm/bridge/analogix/anx7625.h | 24 ++-
2 files changed, 348 insertions(+), 20 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
index 65cc059..372b356 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.c
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -164,6 +164,20 @@ static int anx7625_write_and_or(struct anx7625_data *ctx,
offset, (val & and_mask) | (or_mask));
}

+static int anx7625_config_bit_matrix(struct anx7625_data *ctx)
+{
+ int i, ret;
+
+ ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+ AUDIO_CONTROL_REGISTER, 0x80);
+ for (i = 0; i < 13; i++)
+ ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+ VIDEO_BIT_MATRIX_12 + i,
+ 0x18 + i);
+
+ return ret;
+}
+
static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx)
{
return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_CTRL_STATUS);
@@ -189,10 +203,64 @@ static int wait_aux_op_finish(struct anx7625_data *ctx)
AP_AUX_CTRL_STATUS);
if (val < 0 || (val & 0x0F)) {
DRM_DEV_ERROR(dev, "aux status %02x\n", val);
- val = -EIO;
+ return -EIO;
}

- return val;
+ return 0;
+}
+
+static int anx7625_aux_dpcd_read(struct anx7625_data *ctx,
+ u8 addrh, u8 addrm, u8 addrl,
+ u8 len, u8 *buf)
+{
+ struct device *dev = &ctx->client->dev;
+ int ret;
+ u8 cmd;
+
+ if (len > MAX_DPCD_BUFFER_SIZE) {
+ DRM_DEV_ERROR(dev, "exceed aux buffer len.\n");
+ return -E2BIG;
+ }
+
+ cmd = ((len - 1) << 4) | 0x09;
+
+ /* Set command and length */
+ ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_COMMAND, cmd);
+
+ /* Set aux access address */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_ADDR_7_0, addrl);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_ADDR_15_8, addrm);
+ ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_ADDR_19_16, addrh);
+
+ /* Enable aux access */
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN);
+
+ if (ret < 0) {
+ DRM_DEV_ERROR(dev, "cannot access aux related register.\n");
+ return -EIO;
+ }
+
+ usleep_range(2000, 2100);
+
+ ret = wait_aux_op_finish(ctx);
+ if (ret) {
+ DRM_DEV_ERROR(dev, "aux IO error: wait aux op finish.\n");
+ return ret;
+ }
+
+ ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_BUFF_START, len, buf);
+ if (ret < 0) {
+ DRM_DEV_ERROR(dev, "read dpcd register failed\n");
+ return -EIO;
+ }
+
+ return 0;
}

static int anx7625_video_mute_control(struct anx7625_data *ctx,
@@ -595,6 +663,101 @@ static int anx7625_dsi_config(struct anx7625_data *ctx)
return ret;
}

+static int anx7625_api_dpi_config(struct anx7625_data *ctx)
+{
+ struct device *dev = &ctx->client->dev;
+ u16 freq = ctx->dt.pixelclock.min / 1000;
+ int ret;
+
+ /* configure pixel clock */
+ ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ PIXEL_CLOCK_L, freq & 0xFF);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ PIXEL_CLOCK_H, (freq >> 8));
+
+ /* set DPI mode */
+ /* set to DPI PLL module sel */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_DIGITAL_PLL_9, 0x20);
+ /* power down MIPI */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_LANE_CTRL_10, 0x08);
+ /* enable DPI mode */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_DIGITAL_PLL_18, 0x1C);
+ /* set first edge */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+ VIDEO_CONTROL_0, 0x06);
+ if (ret < 0)
+ DRM_DEV_ERROR(dev, "IO error : dpi phy set failed.\n");
+
+ return ret;
+}
+
+static int anx7625_dpi_config(struct anx7625_data *ctx)
+{
+ struct device *dev = &ctx->client->dev;
+ int ret;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n");
+
+ /* DSC disable */
+ ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+ R_DSC_CTRL_0, ~DSC_EN);
+ if (ret < 0) {
+ DRM_DEV_ERROR(dev, "IO error : disable dsc failed.\n");
+ return ret;
+ }
+
+ ret = anx7625_config_bit_matrix(ctx);
+ if (ret < 0) {
+ DRM_DEV_ERROR(dev, "config bit matrix failed.\n");
+ return ret;
+ }
+
+ ret = anx7625_api_dpi_config(ctx);
+ if (ret < 0) {
+ DRM_DEV_ERROR(dev, "mipi phy(dpi) setup failed.\n");
+ return ret;
+ }
+
+ /* set MIPI RX EN */
+ ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, AP_MIPI_RX_EN);
+ /* clear mute flag */
+ ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+ if (ret < 0)
+ DRM_DEV_ERROR(dev, "IO error : enable mipi rx failed.\n");
+
+ return ret;
+}
+
+static int anx7625_hdcp_setting(struct anx7625_data *ctx)
+{
+ u8 bcap;
+ struct device *dev = &ctx->client->dev;
+
+ if (!(ctx->hdcp_support && ctx->hdcp_en)) {
+ DRM_DEV_DEBUG_DRIVER(dev, "hdcp_support(%d), hdcp_en(%d)\n",
+ ctx->hdcp_support, ctx->hdcp_en);
+ DRM_DEV_DEBUG_DRIVER(dev, "disable HDCP by config\n");
+ return anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+ 0xee, 0x9f);
+ }
+
+ anx7625_aux_dpcd_read(ctx, 0x06, 0x80, 0x28, 1, &bcap);
+ if (!(bcap & 0x01)) {
+ DRM_WARN("downstream not support HDCP 1.4, cap(%x).\n", bcap);
+ return anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+ 0xee, 0x9f);
+ }
+
+ DRM_DEV_DEBUG_DRIVER(dev, "enable HDCP 1.4\n");
+
+ return anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xee, 0x20);
+}
+
static void anx7625_dp_start(struct anx7625_data *ctx)
{
int ret;
@@ -605,9 +768,15 @@ static void anx7625_dp_start(struct anx7625_data *ctx)
return;
}

+ /* HDCP config */
+ anx7625_hdcp_setting(ctx);
+
anx7625_config_audio_input(ctx);

- ret = anx7625_dsi_config(ctx);
+ if (ctx->pdata.is_dpi)
+ ret = anx7625_dpi_config(ctx);
+ else
+ ret = anx7625_dsi_config(ctx);

if (ret < 0)
DRM_DEV_ERROR(dev, "MIPI phy setup error.\n");
@@ -688,8 +857,53 @@ static int sp_tx_get_edid_block(struct anx7625_data *ctx)
return c;
}

-static int edid_read(struct anx7625_data *ctx,
- u8 offset, u8 *pblock_buf)
+static int check_hdcp_support(struct anx7625_data *ctx)
+{
+ int ret;
+ struct device *dev = &ctx->client->dev;
+
+ /* Select HDCP1.4 Key load */
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, FLASH_SRAM_SEL, 0x12);
+ /* Select flash addr low byte */
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, FLASH_ADDR_LOW, 0x91);
+ /* Select flash addr high byte */
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, FLASH_ADDR_HIGH, 0xa0);
+ /* Select sram length high byte */
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, SRAM_LEN_HIGH, 0x00);
+ /* Select sram length low byte */
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, SRAM_LEN_LOW, 0x27);
+ /* Select flash length high byte */
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, FLASH_LEN_HIGH, 0x02);
+ /* Select flash length low byte */
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, FLASH_LEN_LOW, 0x70);
+ /* Select sram addr high byte */
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, SRAM_ADDR_HIGH, 0x00);
+ /* Select sram addr low byte */
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, SRAM_ADDR_LOW, 0x00);
+ /* Enable load with decrypt_en */
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, FLASH_LOAD_STA, 0x03);
+
+ usleep_range(10000, 11000);
+
+ /* Check load status */
+ ret = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, FLASH_LOAD_STA);
+ if (ret < 0) {
+ DRM_DEV_ERROR(dev, "IO error : access flash load.\n");
+ return ret;
+ }
+
+ if ((ret & 0xF2) != 0xF2) {
+ ctx->hdcp_support = 0;
+ DRM_DEV_DEBUG_DRIVER(dev, "not support HDCP\n");
+ } else {
+ ctx->hdcp_support = 1;
+ DRM_DEV_DEBUG_DRIVER(dev, "support HDCP\n");
+ }
+
+ return 0;
+}
+
+static int edid_read(struct anx7625_data *ctx, u8 offset, u8 *pblock_buf)
{
int ret, cnt;
struct device *dev = &ctx->client->dev;
@@ -992,8 +1206,10 @@ static void anx7625_chip_control(struct anx7625_data *ctx, int state)

if (state) {
atomic_inc(&ctx->power_status);
- if (atomic_read(&ctx->power_status) == 1)
+ if (atomic_read(&ctx->power_status) == 1) {
anx7625_power_on_init(ctx);
+ check_hdcp_support(ctx);
+ }
} else {
if (atomic_read(&ctx->power_status)) {
atomic_dec(&ctx->power_status);
@@ -1051,6 +1267,7 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
return;
}

+ ctx->hpd_status = 1;
ctx->hpd_high_cnt++;

/* Not support HDCP */
@@ -1060,8 +1277,10 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10);
/* Interrupt for DRM */
ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01);
- if (ret < 0)
+ if (ret < 0) {
+ DRM_DEV_ERROR(dev, "fail to setting HDCP/auth\n");
return;
+ }

ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86);
if (ret < 0)
@@ -1080,6 +1299,10 @@ static void anx7625_hpd_polling(struct anx7625_data *ctx)
int ret, val;
struct device *dev = &ctx->client->dev;

+ /* Interrupt mode, no need poll HPD status, just return */
+ if (ctx->pdata.intp_irq)
+ return;
+
if (atomic_read(&ctx->power_status) != 1) {
DRM_DEV_DEBUG_DRIVER(dev, "No need to poling HPD status.\n");
return;
@@ -1130,6 +1353,22 @@ static void anx7625_remove_edid(struct anx7625_data *ctx)
ctx->slimport_edid_p.edid_block_num = -1;
}

+static void anx7625_dp_adjust_swing(struct anx7625_data *ctx)
+{
+ struct device *dev = &ctx->client->dev;
+ int i;
+
+ if (!ctx->pdata.reg_table_size)
+ return;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "adjust DP tx swing\n");
+
+ for (i = 0; i < ctx->pdata.reg_table_size; i++)
+ anx7625_reg_write(ctx, ctx->i2c.tx_p1_client,
+ ctx->pdata.art[i].offset & 0xFF,
+ ctx->pdata.art[i].data & 0xFF);
+}
+
static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on)
{
struct device *dev = &ctx->client->dev;
@@ -1145,9 +1384,8 @@ static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on)
} else {
DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n");
anx7625_start_dp_work(ctx);
+ anx7625_dp_adjust_swing(ctx);
}
-
- ctx->hpd_status = 1;
}

static int anx7625_hpd_change_detect(struct anx7625_data *ctx)
@@ -1224,12 +1462,64 @@ static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data)
return IRQ_HANDLED;
}

+static int anx7625_get_u32_value(struct device_node *np,
+ const char *name,
+ int start_pos,
+ int *reg_data)
+{
+ int i, ret;
+
+ /* each slot has 2 cells */
+ for (i = 0; i < 2; i++) {
+ ret = of_property_read_u32_index(np, name,
+ start_pos + i,
+ &reg_data[i]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
static int anx7625_parse_dt(struct device *dev,
struct anx7625_platform_data *pdata)
{
struct device_node *np = dev->of_node;
struct drm_panel *panel;
- int ret;
+ int ret, i;
+ int reg_data[2];
+ int total_size, num_regs, start_pos;
+
+ if (of_get_property(dev->of_node,
+ "analogix,swing-setting", &total_size)) {
+ /* each slot has 2 cells */
+ num_regs = total_size / (sizeof(u32) * 2);
+ if (num_regs > MAX_REG_SIZE)
+ num_regs = MAX_REG_SIZE;
+
+ pdata->reg_table_size = num_regs;
+
+ for (i = 0; i < num_regs; i++) {
+ start_pos = i * 2;
+ ret = anx7625_get_u32_value(np, "analogix,swing-setting",
+ start_pos, reg_data);
+ if (ret) {
+ DRM_DEV_ERROR(dev, "get swing-setting at %d\n",
+ start_pos);
+ return -ENODEV;
+ }
+ pdata->art[i].offset = reg_data[0];
+ pdata->art[i].data = reg_data[1];
+ }
+ }
+
+ ret = of_property_read_u32(dev->of_node, "analogix,mipi-dpi-in",
+ &pdata->is_dpi);
+ if (ret)
+ pdata->is_dpi = 0; /* default dsi mode */
+
+ DRM_DEV_DEBUG_DRIVER(dev, "MIPI RX is %s.\n",
+ pdata->is_dpi ? "DPI" : "DSI");

pdata->mipi_host_node = of_graph_get_remote_node(np, 0, 0);
if (!pdata->mipi_host_node) {
@@ -1237,7 +1527,7 @@ static int anx7625_parse_dt(struct device *dev,
return -ENODEV;
}

- DRM_DEV_DEBUG_DRIVER(dev, "found dsi host node.\n");
+ DRM_DEV_DEBUG_DRIVER(dev, "found MIPI host node.\n");

ret = drm_of_find_panel_or_bridge(np, 1, 0, &panel, NULL);
if (ret < 0) {
@@ -1300,9 +1590,13 @@ static enum drm_connector_status anx7625_sink_detect(struct anx7625_data *ctx)
{
struct device *dev = &ctx->client->dev;

- DRM_DEV_DEBUG_DRIVER(dev, "sink detect, return connected\n");
+ DRM_DEV_DEBUG_DRIVER(dev, "sink detect\n");
+
+ if (ctx->pdata.panel_bridge)
+ return connector_status_connected;

- return connector_status_connected;
+ return ctx->hpd_status ? connector_status_connected :
+ connector_status_disconnected;
}

static int anx7625_attach_dsi(struct anx7625_data *ctx)
@@ -1376,10 +1670,12 @@ static int anx7625_bridge_attach(struct drm_bridge *bridge,
return -ENODEV;
}

- err = anx7625_attach_dsi(ctx);
- if (err) {
- DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err);
- return err;
+ if (!ctx->pdata.is_dpi) {
+ err = anx7625_attach_dsi(ctx);
+ if (err) {
+ DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err);
+ return err;
+ }
}

if (ctx->pdata.panel_bridge) {
@@ -1478,6 +1774,10 @@ static bool anx7625_bridge_mode_fixup(struct drm_bridge *bridge,

DRM_DEV_DEBUG_DRIVER(dev, "drm mode fixup set\n");

+ /* No need fixup for external monitor */
+ if (!ctx->pdata.panel_bridge)
+ return true;
+
hsync = mode->hsync_end - mode->hsync_start;
hfp = mode->hsync_start - mode->hdisplay;
hbp = mode->htotal - mode->hsync_end;
@@ -1777,6 +2077,7 @@ static int anx7625_i2c_probe(struct i2c_client *client,

if (platform->pdata.low_power_mode == 0) {
anx7625_disable_pd_protocol(platform);
+ check_hdcp_support(platform);
atomic_set(&platform->power_status, 1);
}

@@ -1786,8 +2087,13 @@ static int anx7625_i2c_probe(struct i2c_client *client,

platform->bridge.funcs = &anx7625_bridge_funcs;
platform->bridge.of_node = client->dev.of_node;
- platform->bridge.ops = DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_HPD;
- platform->bridge.type = DRM_MODE_CONNECTOR_eDP;
+ platform->bridge.ops = DRM_BRIDGE_OP_EDID;
+ if (!platform->pdata.panel_bridge)
+ platform->bridge.ops |= DRM_BRIDGE_OP_HPD |
+ DRM_BRIDGE_OP_DETECT;
+ platform->bridge.type = platform->pdata.panel_bridge ?
+ DRM_MODE_CONNECTOR_eDP :
+ DRM_MODE_CONNECTOR_DisplayPort;
drm_bridge_add(&platform->bridge);

DRM_DEV_DEBUG_DRIVER(dev, "probe done\n");
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
index 193ad86..0223e07 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.h
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
@@ -146,9 +146,19 @@

#define I2C_ADDR_7E_FLASH_CONTROLLER 0x7E

-#define FLASH_LOAD_STA 0x05
+#define FLASH_SRAM_SEL 0x00
+#define SRAM_ADDR_HIGH 0x01
+#define SRAM_ADDR_LOW 0x02
+#define SRAM_LEN_HIGH 0x03
+#define SRAM_LEN_LOW 0x04
+#define FLASH_LOAD_STA 0x05
#define FLASH_LOAD_STA_CHK BIT(7)

+#define FLASH_ADDR_LOW 0x0F
+#define FLASH_ADDR_HIGH 0x10
+#define FLASH_LEN_HIGH 0x31
+#define FLASH_LEN_LOW 0x32
+
#define XTAL_FRQ_SEL 0x3F
/* bit field positions */
#define XTAL_FRQ_SEL_POS 5
@@ -340,6 +350,8 @@ enum audio_wd_len {
#define EDID_TRY_CNT 3
#define SUPPORT_PIXEL_CLOCK 300000

+#define MAX_REG_SIZE 64
+
struct s_edid_data {
int edid_block_num;
u8 edid_raw_data[FOUR_BLOCK_SIZE];
@@ -347,11 +359,19 @@ struct s_edid_data {

/***************** Display End *****************/

+struct anx7625_reg_table {
+ int offset;
+ int data;
+};
+
struct anx7625_platform_data {
struct gpio_desc *gpio_p_on;
struct gpio_desc *gpio_reset;
struct drm_bridge *panel_bridge;
int intp_irq;
+ int is_dpi;
+ int reg_table_size;
+ struct anx7625_reg_table art[MAX_REG_SIZE];
u32 low_power_mode;
struct device_node *mipi_host_node;
};
@@ -371,6 +391,8 @@ struct anx7625_data {
atomic_t power_status;
int hpd_status;
int hpd_high_cnt;
+ int hdcp_support;
+ int hdcp_en;
/* Lock for work queue */
struct mutex lock;
struct i2c_client *client;
--
2.7.4