[PATCH v3 2/4] hwmon: (ltc2945): clamp values before converting

[Alexandru Ardelean]

We can compute the full-scale values for power, voltages and current, and
apply them before conversion.

This way we sanitize the input from userspace a bit.
We can't however clamp the value for power, since that is represented in
micro-Watts. The full-scale power that can be represented is around 10480
Watts, which in micro-Watts ends up being around 10 billion micro-Watts.

Current and voltage is represented in millis, so these can be clamped.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@xxxxxxxxxx>
---
 drivers/hwmon/ltc2945.c | 48 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 48 insertions(+)

diff --git a/drivers/hwmon/ltc2945.c b/drivers/hwmon/ltc2945.c
index 42a59170da78..41df2c8b7673 100644
--- a/drivers/hwmon/ltc2945.c
+++ b/drivers/hwmon/ltc2945.c
@@ -58,6 +58,15 @@
 #define CONTROL_MULT_SELECT	(1 << 0)
 #define CONTROL_TEST_MODE	(1 << 4)
 
+/* Full scale ranges (page 4 of the datasheet) */
+
+#define LTC2945_VIN_FULL_SCALE_MV	102375
+#define LTC2945_ADIN_FULL_SCALE_MV	2048
+
+/* Power and current computed assuming a 1mOhm sense resistor */
+#define LTC2945_POWER_FULL_SCALE_UW	10485759375ULL
+#define LTC2945_SENSE_FULL_SCALE_MA	102375
+
 /**
  * struct ltc2945_state - driver instance specific data
  * @regmap:		regmap object to access device registers
@@ -154,6 +163,43 @@ static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
 	return val;
 }
 
+static unsigned long ltc2945_val_clamp(u8 reg, unsigned long val)
+{
+	switch (reg) {
+	case LTC2945_POWER_H:
+	case LTC2945_MAX_POWER_H:
+	case LTC2945_MIN_POWER_H:
+	case LTC2945_MAX_POWER_THRES_H:
+	case LTC2945_MIN_POWER_THRES_H:
+		/* No sense in clamping now, LTC2945_POWER_FULL_SCALE_UW is larger than UINT32_MAX */
+		return val;
+	case LTC2945_VIN_H:
+	case LTC2945_MAX_VIN_H:
+	case LTC2945_MIN_VIN_H:
+	case LTC2945_MAX_VIN_THRES_H:
+	case LTC2945_MIN_VIN_THRES_H:
+		return clamp_val(val, 0, LTC2945_VIN_FULL_SCALE_MV);
+	case LTC2945_ADIN_H:
+	case LTC2945_MAX_ADIN_H:
+	case LTC2945_MIN_ADIN_THRES_H:
+	case LTC2945_MAX_ADIN_THRES_H:
+	case LTC2945_MIN_ADIN_H:
+		return clamp_val(val, 0, LTC2945_ADIN_FULL_SCALE_MV);
+	case LTC2945_SENSE_H:
+	case LTC2945_MAX_SENSE_H:
+	case LTC2945_MIN_SENSE_H:
+	case LTC2945_MAX_SENSE_THRES_H:
+	case LTC2945_MIN_SENSE_THRES_H:
+		return clamp_val(val, 0, LTC2945_SENSE_FULL_SCALE_MA);
+	default:
+		/*
+		 * This is unlikely to happen, and if it does, it should
+		 * error out on the next call, we can't return negative here
+		 */
+		return 0;
+	}
+}
+
 static int ltc2945_val_to_reg(struct device *dev, u8 reg,
 			      unsigned long val)
 {
@@ -257,6 +303,8 @@ static ssize_t ltc2945_value_store(struct device *dev,
 	if (ret)
 		return ret;
 
+	val = ltc2945_val_clamp(reg, val);
+
 	/* convert to register value, then clamp and write result */
 	regval = ltc2945_val_to_reg(dev, reg, val);
 	if (is_power_reg(reg)) {
-- 
2.17.1