[PATCH] net: ftgmac100: Support phyless operation

[William A. Kennington III]

We have BMC to BMC connections that lack a PHY in between but don't
want to use the NC-SI state machinery of the kernel. Instead,
allow for an option to disable the phy detection and mdio logic.

Signed-off-by: William A. Kennington III <wak@xxxxxxxxxx>
---
 .../devicetree/bindings/net/ftgmac100.txt     |  2 ++
 drivers/net/ethernet/faraday/ftgmac100.c      | 30 +++++++++++--------
 2 files changed, 19 insertions(+), 13 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/ftgmac100.txt b/Documentation/devicetree/bindings/net/ftgmac100.txt
index 29234021f601..22c729c5fd3e 100644
--- a/Documentation/devicetree/bindings/net/ftgmac100.txt
+++ b/Documentation/devicetree/bindings/net/ftgmac100.txt
@@ -19,6 +19,8 @@ Optional properties:
 - phy-mode: See ethernet.txt file in the same directory. If the property is
   absent, "rgmii" is assumed. Supported values are "rgmii*" and "rmii" for
   aspeed parts. Other (unknown) parts will accept any value.
+- no-phy: Disable any MDIO or PHY connection logic and assume the interface
+  is always up.
 - use-ncsi: Use the NC-SI stack instead of an MDIO PHY. Currently assumes
   rmii (100bT) but kept as a separate property in case NC-SI grows support
   for a gigabit link.
diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index 88bfe2107938..f2cf190654c8 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -1467,18 +1467,18 @@ static int ftgmac100_open(struct net_device *netdev)
 		return err;
 	}
 
-	/* When using NC-SI we force the speed to 100Mbit/s full duplex,
+	/* When PHYless we force the speed to 100Mbit/s full duplex,
 	 *
 	 * Otherwise we leave it set to 0 (no link), the link
 	 * message from the PHY layer will handle setting it up to
 	 * something else if needed.
 	 */
-	if (priv->use_ncsi) {
-		priv->cur_duplex = DUPLEX_FULL;
-		priv->cur_speed = SPEED_100;
-	} else {
+	if (netdev->phydev) {
 		priv->cur_duplex = 0;
 		priv->cur_speed = 0;
+	} else {
+		priv->cur_duplex = DUPLEX_FULL;
+		priv->cur_speed = SPEED_100;
 	}
 
 	/* Reset the hardware */
@@ -1506,14 +1506,16 @@ static int ftgmac100_open(struct net_device *netdev)
 	if (netdev->phydev) {
 		/* If we have a PHY, start polling */
 		phy_start(netdev->phydev);
-	} else if (priv->use_ncsi) {
-		/* If using NC-SI, set our carrier on and start the stack */
+	} else {
+		/* If PHYless, set our carrier on and start the stack */
 		netif_carrier_on(netdev);
 
-		/* Start the NCSI device */
-		err = ncsi_start_dev(priv->ndev);
-		if (err)
-			goto err_ncsi;
+		if (priv->use_ncsi) {
+			/* Start the NCSI device */
+			err = ncsi_start_dev(priv->ndev);
+			if (err)
+				goto err_ncsi;
+		}
 	}
 
 	return 0;
@@ -1725,8 +1727,8 @@ static int ftgmac100_setup_clk(struct ftgmac100 *priv)
 	 * 1000Mbit link speeds. As NCSI is limited to 100Mbit, 25MHz
 	 * is sufficient
 	 */
-	rc = clk_set_rate(priv->clk, priv->use_ncsi ? FTGMAC_25MHZ :
-			  FTGMAC_100MHZ);
+	rc = clk_set_rate(priv->clk, priv->netdev->phydev ? FTGMAC_100MHZ :
+			  FTGMAC_25MHZ);
 	if (rc)
 		goto cleanup_clk;
 
@@ -1837,6 +1839,8 @@ static int ftgmac100_probe(struct platform_device *pdev)
 		priv->ndev = ncsi_register_dev(netdev, ftgmac100_ncsi_handler);
 		if (!priv->ndev)
 			goto err_phy_connect;
+	} else if (np && of_get_property(np, "no-phy", NULL)) {
+		dev_info(&pdev->dev, "Using PHYless interface\n");
 	} else if (np && of_get_property(np, "phy-handle", NULL)) {
 		struct phy_device *phy;
 
-- 
2.30.0.478.g8a0d178c01-goog