[PATCH net 1/1] net: stmmac: fix CBS idleslope and sendslope calculation
From: Song Yoong Siang
Date: Thu Feb 18 2021 - 00:57:39 EST
From: "Song, Yoong Siang" <yoong.siang.song@xxxxxxxxx>
When link speed is not 100 Mbps, port transmit rate and speed divider
are set to 8 and 1000000 respectively. These values are incorrect for
CBS idleslope and sendslope HW values calculation if the link speed is
not 1 Gbps.
This patch adds switch statement to set the values of port transmit rate
and speed divider for 10 Gbps, 5 Gbps, 2.5 Gbps, 1 Gbps, and 100 Mbps.
Note that CBS is not supported at 10 Mbps.
Fixes: bc41a6689b30 ("net: stmmac: tc: Remove the speed dependency")
Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Song, Yoong Siang <yoong.siang.song@xxxxxxxxx>
---
drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c | 30 +++++++++++++++++++++----
1 file changed, 26 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
index 5698554..44bb133 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
@@ -316,6 +316,32 @@ static int tc_setup_cbs(struct stmmac_priv *priv,
if (!priv->dma_cap.av)
return -EOPNOTSUPP;
+ /* Port Transmit Rate and Speed Divider */
+ switch (priv->speed) {
+ case SPEED_10000:
+ ptr = 32;
+ speed_div = 10000000;
+ break;
+ case SPEED_5000:
+ ptr = 32;
+ speed_div = 5000000;
+ break;
+ case SPEED_2500:
+ ptr = 8;
+ speed_div = 2500000;
+ break;
+ case SPEED_1000:
+ ptr = 8;
+ speed_div = 1000000;
+ break;
+ case SPEED_100:
+ ptr = 4;
+ speed_div = 100000;
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+
mode_to_use = priv->plat->tx_queues_cfg[queue].mode_to_use;
if (mode_to_use == MTL_QUEUE_DCB && qopt->enable) {
ret = stmmac_dma_qmode(priv, priv->ioaddr, queue, MTL_QUEUE_AVB);
@@ -332,10 +358,6 @@ static int tc_setup_cbs(struct stmmac_priv *priv,
priv->plat->tx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB;
}
- /* Port Transmit Rate and Speed Divider */
- ptr = (priv->speed == SPEED_100) ? 4 : 8;
- speed_div = (priv->speed == SPEED_100) ? 100000 : 1000000;
-
/* Final adjustments for HW */
value = div_s64(qopt->idleslope * 1024ll * ptr, speed_div);
priv->plat->tx_queues_cfg[queue].idle_slope = value & GENMASK(31, 0);
--
2.7.4