Re: [RFC PATCH v3 1/1] scsi: ufs: Enable power management for wlun
From: Adrian Hunter
Date: Fri Feb 19 2021 - 03:36:43 EST
On 11/02/21 9:18 pm, Asutosh Das wrote:
> During runtime-suspend of ufs host, the scsi devices are
> already suspended and so are the queues associated with them.
> But the ufs host sends SSU to wlun during its runtime-suspend.
> During the process blk_queue_enter checks if the queue is not in
> suspended state. If so, it waits for the queue to resume, and never
> comes out of it.
> The commit
> (d55d15a33: scsi: block: Do not accept any requests while suspended)
> adds the check if the queue is in suspended state in blk_queue_enter().
>
> Call trace:
> __switch_to+0x174/0x2c4
> __schedule+0x478/0x764
> schedule+0x9c/0xe0
> blk_queue_enter+0x158/0x228
> blk_mq_alloc_request+0x40/0xa4
> blk_get_request+0x2c/0x70
> __scsi_execute+0x60/0x1c4
> ufshcd_set_dev_pwr_mode+0x124/0x1e4
> ufshcd_suspend+0x208/0x83c
> ufshcd_runtime_suspend+0x40/0x154
> ufshcd_pltfrm_runtime_suspend+0x14/0x20
> pm_generic_runtime_suspend+0x28/0x3c
> __rpm_callback+0x80/0x2a4
> rpm_suspend+0x308/0x614
> rpm_idle+0x158/0x228
> pm_runtime_work+0x84/0xac
> process_one_work+0x1f0/0x470
> worker_thread+0x26c/0x4c8
> kthread+0x13c/0x320
> ret_from_fork+0x10/0x18
>
> Fix this by registering ufs device wlun as a scsi driver and
> registering it for block runtime-pm. Also make this as a
> supplier for all other luns. That way, this device wlun
> suspends after all the consumers and resumes after
> hba resumes.
Sounds reasonable. Thanks for doing this. Some comments below.
>
> Co-developed-by: Can Guo <cang@xxxxxxxxxxxxxx>
> Signed-off-by: Can Guo <cang@xxxxxxxxxxxxxx>
> Signed-off-by: Asutosh Das <asutoshd@xxxxxxxxxxxxxx>
> ---
> drivers/scsi/ufs/ufshcd.c | 415 +++++++++++++++++++++++++++++++++++++--------
> drivers/scsi/ufs/ufshcd.h | 4 +
> include/trace/events/ufs.h | 20 +++
> 3 files changed, 364 insertions(+), 75 deletions(-)
>
> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> index 45624c7..e92dbde 100644
> --- a/drivers/scsi/ufs/ufshcd.c
> +++ b/drivers/scsi/ufs/ufshcd.c
> @@ -16,6 +16,7 @@
> #include <linux/bitfield.h>
> #include <linux/blk-pm.h>
> #include <linux/blkdev.h>
> +#include <scsi/scsi_driver.h>
> #include "ufshcd.h"
> #include "ufs_quirks.h"
> #include "unipro.h"
> @@ -251,6 +252,13 @@ static int ufshcd_wb_toggle_flush_during_h8(struct ufs_hba *hba, bool set);
> static inline int ufshcd_wb_toggle_flush(struct ufs_hba *hba, bool enable);
> static void ufshcd_hba_vreg_set_lpm(struct ufs_hba *hba);
> static void ufshcd_hba_vreg_set_hpm(struct ufs_hba *hba);
> +static int __ufshcd_wl_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op);
> +static int __ufshcd_wl_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op);
> +static int ufshcd_wl_runtime_suspend(struct device *dev);
> +static int ufshcd_wl_runtime_resume(struct device *dev);
> +static int ufshcd_wl_suspend(struct device *dev);
> +static int ufshcd_wl_resume(struct device *dev);
> +static void ufshcd_wl_shutdown(struct device *dev);
Please try to reduce the number of forward declarations.
>
> static inline bool ufshcd_valid_tag(struct ufs_hba *hba, int tag)
> {
> @@ -2572,6 +2580,17 @@ static inline u16 ufshcd_upiu_wlun_to_scsi_wlun(u8 upiu_wlun_id)
> return (upiu_wlun_id & ~UFS_UPIU_WLUN_ID) | SCSI_W_LUN_BASE;
> }
>
> +static inline bool is_rpmb_wlun(struct scsi_device *sdev)
> +{
> + return (sdev->lun == ufshcd_upiu_wlun_to_scsi_wlun(UFS_UPIU_RPMB_WLUN));
> +}
> +
> +static inline bool is_device_wlun(struct scsi_device *sdev)
> +{
> + return (sdev->lun ==
> + ufshcd_upiu_wlun_to_scsi_wlun(UFS_UPIU_UFS_DEVICE_WLUN));
> +}
> +
> static void ufshcd_init_lrb(struct ufs_hba *hba, struct ufshcd_lrb *lrb, int i)
> {
> struct utp_transfer_cmd_desc *cmd_descp = hba->ucdl_base_addr;
> @@ -4808,6 +4827,43 @@ static inline void ufshcd_get_lu_power_on_wp_status(struct ufs_hba *hba,
> }
>
> /**
> + * ufshcd_setup_links - associate link b/w device wlun and other luns
> + * @sdev: pointer to SCSI device
> + * @hba: pointer to ufs hba
> + *
> + * Returns void
> + */
> +static void ufshcd_setup_links(struct ufs_hba *hba, struct scsi_device *sdev)
> +{
> + struct device_link *link;
> +
> + /*
> + * device wlun is the supplier & rest of the luns are consumers
> + * This ensures that device wlun suspends after all other luns.
> + */
> + if (hba->sdev_ufs_device) {
> + link = device_link_add(&sdev->sdev_gendev,
> + &hba->sdev_ufs_device->sdev_gendev,
> + DL_FLAG_PM_RUNTIME);
> + if (!link) {
> + dev_err(&sdev->sdev_gendev, "Failed establishing link - %s\n",
> + dev_name(&hba->sdev_ufs_device->sdev_gendev));
> + return;
> + }
> + hba->luns_avail--;
> + /* Ignore REPORT_LUN wlun probing */
> + if (hba->luns_avail != 1)
> + return;
> +
> + pm_runtime_put_noidle(&hba->sdev_ufs_device->sdev_gendev);
> + pm_runtime_mark_last_busy(&hba->sdev_ufs_device->sdev_gendev);
> + } else {
> + /* device wlun is probed */
> + hba->luns_avail--;
> + }
> +}
> +
> +/**
> * ufshcd_slave_alloc - handle initial SCSI device configurations
> * @sdev: pointer to SCSI device
> *
> @@ -4838,6 +4894,8 @@ static int ufshcd_slave_alloc(struct scsi_device *sdev)
>
> ufshcd_get_lu_power_on_wp_status(hba, sdev);
>
> + ufshcd_setup_links(hba, sdev);
> +
> return 0;
> }
>
> @@ -5589,8 +5647,8 @@ static void ufshcd_rpm_dev_flush_recheck_work(struct work_struct *work)
> * after a certain delay to recheck the threshold by next runtime
> * suspend.
> */
> - pm_runtime_get_sync(hba->dev);
> - pm_runtime_put_sync(hba->dev);
> + scsi_autopm_get_device(hba->sdev_ufs_device);
> + scsi_autopm_put_device(hba->sdev_ufs_device);
> }
>
> /**
> @@ -7254,6 +7312,14 @@ static int ufshcd_scsi_add_wlus(struct ufs_hba *hba)
> goto out;
> }
> ufshcd_blk_pm_runtime_init(hba->sdev_ufs_device);
> + /*
> + * A pm_runtime_put_sync is invoked when this device enables blk_pm_runtime
> + * & would suspend the device-wlun upon timer expiry.
> + * But suspending device wlun _may_ put the ufs device in the pre-defined
> + * low power mode (SSU <rpm_lvl>). Probing of other luns may fail then.
> + * Don't allow this suspend until all the luns have been probed.
> + */
> + pm_runtime_get_noresume(&hba->sdev_ufs_device->sdev_gendev);
> scsi_device_put(hba->sdev_ufs_device);
>
> hba->sdev_rpmb = __scsi_add_device(hba->host, 0, 0,
> @@ -7417,6 +7483,9 @@ static int ufs_get_device_desc(struct ufs_hba *hba)
> goto out;
> }
>
> + hba->luns_avail = desc_buf[DEVICE_DESC_PARAM_NUM_LU] +
> + desc_buf[DEVICE_DESC_PARAM_NUM_WLU];
> +
> ufs_fixup_device_setup(hba);
>
> ufshcd_wb_probe(hba, desc_buf);
> @@ -7747,6 +7816,54 @@ static int ufshcd_device_params_init(struct ufs_hba *hba)
> return ret;
> }
>
> +static int ufshcd_wl_probe(struct device *dev)
> +{
> + struct scsi_device *sdev = to_scsi_device(dev);
> +
> + /*
> + * Use this driver for both device wlun and rpmb lun
> + * It's used to send uac to rpmb wlun and ssu to device wlun
> + */
> + if (sdev && (is_rpmb_wlun(sdev) || is_device_wlun(sdev)))
> + return 0;
> + return -ENODEV;
> +}
> +
> +static int ufshcd_wl_remove(struct device *dev)
> +{
> + struct scsi_device *sdev = to_scsi_device(dev);
> +
> + scsi_remove_device(sdev);
> + return 0;
> +}
> +
> +static const struct dev_pm_ops ufshcd_wl_pm_ops = {
> + SET_RUNTIME_PM_OPS(ufshcd_wl_runtime_suspend, ufshcd_wl_runtime_resume, NULL)
> + SET_SYSTEM_SLEEP_PM_OPS(ufshcd_wl_suspend, ufshcd_wl_resume)
> +};
> +
> +/**
> + * ufs_wlun - describes 2 wluns:
> + * ufs-device wlun - used to send pm commands
> + * and rpmb wlun - for rpmb commands
There seems to be no common code for those 2, so could they be separate drivers?
> + * All luns including rpmb are consumers of ufs-device wlun.
> + *
> + * Currently, no sd driver is present for wluns.
> + * Hence the no specific pm operations are performed.
> + * With ufs design, SSU should be sent to ufs-device wlun.
> + * Hence register a scsi driver for ufs wluns only.
> + */
> +static struct scsi_driver ufs_wlun = {
> + .gendrv = {
> + .name = "ufs_device_wlun",
> + .owner = THIS_MODULE,
> + .probe = ufshcd_wl_probe,
> + .remove = ufshcd_wl_remove,
> + .pm = &ufshcd_wl_pm_ops,
> + .shutdown = ufshcd_wl_shutdown,
> + },
> +};
> +
> /**
> * ufshcd_add_lus - probe and add UFS logical units
> * @hba: per-adapter instance
> @@ -7755,6 +7872,12 @@ static int ufshcd_add_lus(struct ufs_hba *hba)
> {
> int ret;
>
> + ret = scsi_register_driver(&ufs_wlun.gendrv);
> + if (ret) {
> + dev_err(hba->dev, "Register device wlun driver failed: %d\n",
> + ret);
> + return ret;
> + }
> /* Add required well known logical units to scsi mid layer */
> ret = ufshcd_scsi_add_wlus(hba);
> if (ret)
> @@ -7964,6 +8087,7 @@ static void ufshcd_async_scan(void *data, async_cookie_t cookie)
> pm_runtime_put_sync(hba->dev);
> ufshcd_hba_exit(hba);
> }
> + hba->init_done = true;
> }
>
> static const struct attribute_group *ufshcd_driver_groups[] = {
> @@ -8475,7 +8599,8 @@ static int ufshcd_set_dev_pwr_mode(struct ufs_hba *hba,
> * handling context.
> */
> hba->host->eh_noresume = 1;
> - ufshcd_clear_ua_wluns(hba);
> + if (hba->wlun_dev_clr_ua)
> + ufshcd_clear_ua_wlun(hba, UFS_UPIU_UFS_DEVICE_WLUN);
>
> cmd[4] = pwr_mode << 4;
>
> @@ -8650,26 +8775,9 @@ static void ufshcd_hba_vreg_set_hpm(struct ufs_hba *hba)
> ufshcd_setup_hba_vreg(hba, true);
> }
>
> -/**
> - * ufshcd_suspend - helper function for suspend operations
> - * @hba: per adapter instance
> - * @pm_op: desired low power operation type
> - *
> - * This function will try to put the UFS device and link into low power
> - * mode based on the "rpm_lvl" (Runtime PM level) or "spm_lvl"
> - * (System PM level).
> - *
> - * If this function is called during shutdown, it will make sure that
> - * both UFS device and UFS link is powered off.
> - *
> - * NOTE: UFS device & link must be active before we enter in this function.
> - *
> - * Returns 0 for success and non-zero for failure
> - */
> -static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> +static int __ufshcd_wl_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> {
> int ret = 0;
> - int check_for_bkops;
> enum ufs_pm_level pm_lvl;
> enum ufs_dev_pwr_mode req_dev_pwr_mode;
> enum uic_link_state req_link_state;
> @@ -8690,24 +8798,23 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> * just gate the clocks.
> */
> ufshcd_hold(hba, false);
> - hba->clk_gating.is_suspended = true;
>
> if (ufshcd_is_clkscaling_supported(hba))
> ufshcd_clk_scaling_suspend(hba, true);
>
> if (req_dev_pwr_mode == UFS_ACTIVE_PWR_MODE &&
> req_link_state == UIC_LINK_ACTIVE_STATE) {
> - goto disable_clks;
> + goto enable_scaling;
> }
>
> if ((req_dev_pwr_mode == hba->curr_dev_pwr_mode) &&
> (req_link_state == hba->uic_link_state))
> - goto enable_gating;
> + goto enable_scaling;
>
> /* UFS device & link must be active before we enter in this function */
> if (!ufshcd_is_ufs_dev_active(hba) || !ufshcd_is_link_active(hba)) {
> ret = -EINVAL;
> - goto enable_gating;
> + goto enable_scaling;
> }
>
> if (ufshcd_is_runtime_pm(pm_op)) {
> @@ -8719,7 +8826,7 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> */
> ret = ufshcd_urgent_bkops(hba);
> if (ret)
> - goto enable_gating;
> + goto enable_scaling;
> } else {
> /* make sure that auto bkops is disabled */
> ufshcd_disable_auto_bkops(hba);
> @@ -8746,10 +8853,214 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>
> if (!hba->dev_info.b_rpm_dev_flush_capable) {
> ret = ufshcd_set_dev_pwr_mode(hba, req_dev_pwr_mode);
> - if (ret)
> - goto enable_gating;
> + if (!ret)
> + goto out;
> }
> }
> +enable_scaling:
> + if (ufshcd_is_clkscaling_supported(hba))
> + ufshcd_clk_scaling_suspend(hba, false);
> +
> + hba->dev_info.b_rpm_dev_flush_capable = false;
> +out:
> + if (hba->dev_info.b_rpm_dev_flush_capable) {
> + schedule_delayed_work(&hba->rpm_dev_flush_recheck_work,
> + msecs_to_jiffies(RPM_DEV_FLUSH_RECHECK_WORK_DELAY_MS));
> + }
> + if (ret)
> + ufshcd_update_evt_hist(hba, UFS_EVT_WL_SUSP_ERR, (u32)ret);
> + ufshcd_release(hba);
> + return ret;
> +}
> +
> +static int __ufshcd_wl_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> +{
> + int ret = 0;
> + enum uic_link_state old_link_state;
> +
> + if (!hba->init_done)
> + return 0;
> +
> + old_link_state = hba->uic_link_state;
> + ufshcd_hold(hba, false);
> + if (!ufshcd_is_ufs_dev_active(hba)) {
You cannot assume the UFS device is not in DeepSleep here.
i.e. the host controller may not have been suspended and resumed since the
UFS device entered DeepSleep.
> + ret = ufshcd_set_dev_pwr_mode(hba, UFS_ACTIVE_PWR_MODE);
> + if (ret)
> + goto out;
> + }
> +
> + if (ufshcd_keep_autobkops_enabled_except_suspend(hba))
> + ufshcd_enable_auto_bkops(hba);
> + else
> + /*
> + * If BKOPs operations are urgently needed at this moment then
> + * keep auto-bkops enabled or else disable it.
> + */
> + ufshcd_urgent_bkops(hba);
> +
> + if (hba->clk_scaling.is_allowed)
> + ufshcd_resume_clkscaling(hba);
> +
> + if (hba->dev_info.b_rpm_dev_flush_capable) {
> + hba->dev_info.b_rpm_dev_flush_capable = false;
> + cancel_delayed_work(&hba->rpm_dev_flush_recheck_work);
> + }
> +
> +out:
> + hba->clk_gating.is_suspended = false;
> + if (ret)
> + ufshcd_update_evt_hist(hba, UFS_EVT_WL_RES_ERR, (u32)ret);
> + ufshcd_release(hba);
> + return ret;
> +}
> +
> +static int ufshcd_wl_runtime_suspend(struct device *dev)
> +{
> + struct scsi_device *sdev = to_scsi_device(dev);
> + struct ufs_hba *hba;
> + int ret;
> + ktime_t start = ktime_get();
> +
> + hba = shost_priv(sdev->host);
> + if (is_rpmb_wlun(sdev)) {
> + if (hba->sdev_rpmb)
> + return ufshcd_clear_ua_wlun(hba, UFS_UPIU_RPMB_WLUN);
> + return 0;
> + }
> +
> + ret = __ufshcd_wl_suspend(hba, UFS_RUNTIME_PM);
> + if (ret)
> + dev_err(&sdev->sdev_gendev, "%s failed: %d\n", __func__, ret);
> +
> + trace_ufshcd_wl_runtime_suspend(dev_name(dev), ret,
> + ktime_to_us(ktime_sub(ktime_get(), start)),
> + hba->curr_dev_pwr_mode, hba->uic_link_state);
> +
> + return ret;
> +}
> +
> +static int ufshcd_wl_runtime_resume(struct device *dev)
> +{
> + struct scsi_device *sdev = to_scsi_device(dev);
> + struct ufs_hba *hba;
> + int ret;
> + ktime_t start = ktime_get();
> +
> + hba = shost_priv(sdev->host);
> +
> + if (is_rpmb_wlun(sdev))
> + return 0;
> + ret = __ufshcd_wl_resume(hba, UFS_RUNTIME_PM);
> + if (ret)
> + dev_err(&sdev->sdev_gendev, "%s failed: %d\n", __func__, ret);
> +
> + trace_ufshcd_wl_runtime_resume(dev_name(dev), ret,
> + ktime_to_us(ktime_sub(ktime_get(), start)),
> + hba->curr_dev_pwr_mode, hba->uic_link_state);
> +
> + return ret;
> +}
> +
> +static int ufshcd_wl_suspend(struct device *dev)
> +{
> + struct scsi_device *sdev = to_scsi_device(dev);
> + struct ufs_hba *hba;
> + int ret;
> + ktime_t start = ktime_get();
> +
> + if (is_rpmb_wlun(sdev))
> + return 0;
> + hba = shost_priv(sdev->host);
> + ret = __ufshcd_wl_suspend(hba, UFS_SYSTEM_PM);
> + if (ret)
> + dev_err(&sdev->sdev_gendev, "%s failed: %d\n", __func__, ret);
> +
> + trace_ufshcd_wl_suspend(dev_name(dev), ret,
> + ktime_to_us(ktime_sub(ktime_get(), start)),
> + hba->curr_dev_pwr_mode, hba->uic_link_state);
> +
> + return ret;
> +
> +}
> +
> +static int ufshcd_wl_resume(struct device *dev)
> +{
> + struct scsi_device *sdev = to_scsi_device(dev);
> + struct ufs_hba *hba;
> + int ret;
> + ktime_t start = ktime_get();
> +
> + if (pm_runtime_suspended(dev) || is_rpmb_wlun(sdev))
> + return 0;
> + hba = shost_priv(sdev->host);
> +
> + ret = __ufshcd_wl_resume(hba, UFS_SYSTEM_PM);
> + if (ret)
> + dev_err(&sdev->sdev_gendev, "%s failed: %d\n", __func__, ret);
> +
> + trace_ufshcd_wl_resume(dev_name(dev), ret,
> + ktime_to_us(ktime_sub(ktime_get(), start)),
> + hba->curr_dev_pwr_mode, hba->uic_link_state);
> +
> + return ret;
> +}
> +
> +static void ufshcd_wl_shutdown(struct device *dev)
> +{
> + struct scsi_device *sdev = to_scsi_device(dev);
> + struct ufs_hba *hba;
> +
> + if (is_rpmb_wlun(sdev))
> + return;
> + hba = shost_priv(sdev->host);
> + scsi_device_quiesce(sdev);
> + shost_for_each_device(sdev, hba->host) {
> + if (sdev == hba->sdev_ufs_device)
> + continue;
> + scsi_remove_device(sdev);
> + }
> + __ufshcd_wl_suspend(hba, UFS_SHUTDOWN_PM);
> +}
> +
> +/**
> + * ufshcd_suspend - helper function for suspend operations
> + * @hba: per adapter instance
> + * @pm_op: desired low power operation type
> + *
> + * This function will try to put the UFS link into low power
> + * mode based on the "rpm_lvl" (Runtime PM level) or "spm_lvl"
> + * (System PM level).
> + *
> + * If this function is called during shutdown, it will make sure that
> + * link is powered off.
> + *
> + * Returns 0 for success and non-zero for failure
> + */
> +static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> +{
> + int ret = 0;
> + int check_for_bkops;
> + enum ufs_pm_level pm_lvl;
> + enum ufs_dev_pwr_mode req_dev_pwr_mode;
> + enum uic_link_state req_link_state;
> +
> + hba->pm_op_in_progress = 1;
> + if (!ufshcd_is_shutdown_pm(pm_op)) {
> + pm_lvl = ufshcd_is_runtime_pm(pm_op) ?
> + hba->rpm_lvl : hba->spm_lvl;
> + req_dev_pwr_mode = ufs_get_pm_lvl_to_dev_pwr_mode(pm_lvl);
> + req_link_state = ufs_get_pm_lvl_to_link_pwr_state(pm_lvl);
> + } else {
> + req_dev_pwr_mode = UFS_POWERDOWN_PWR_MODE;
> + req_link_state = UIC_LINK_OFF_STATE;
> + }
> +
> + /*
> + * If we can't transition into any of the low power modes
> + * just gate the clocks.
> + */
> + ufshcd_hold(hba, false);
> + hba->clk_gating.is_suspended = true;
>
> /*
> * In the case of DeepSleep, the device is expected to remain powered
> @@ -8758,9 +9069,8 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> check_for_bkops = !ufshcd_is_ufs_dev_deepsleep(hba);
> ret = ufshcd_link_state_transition(hba, req_link_state, check_for_bkops);
> if (ret)
> - goto set_dev_active;
> + goto enable_gating;
>
> -disable_clks:
> /*
> * Call vendor specific suspend callback. As these callbacks may access
> * vendor specific host controller register space call them before the
> @@ -8790,7 +9100,6 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> goto out;
>
> set_link_active:
> - ufshcd_vreg_set_hpm(hba);
> /*
> * Device hardware reset is required to exit DeepSleep. Also, for
> * DeepSleep, the link is off so host reset and restore will be done
> @@ -8804,28 +9113,15 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> ufshcd_set_link_active(hba);
> else if (ufshcd_is_link_off(hba))
> ufshcd_host_reset_and_restore(hba);
> -set_dev_active:
> /* Can also get here needing to exit DeepSleep */
> if (ufshcd_is_ufs_dev_deepsleep(hba)) {
> ufshcd_device_reset(hba);
> ufshcd_host_reset_and_restore(hba);
> }
> - if (!ufshcd_set_dev_pwr_mode(hba, UFS_ACTIVE_PWR_MODE))
> - ufshcd_disable_auto_bkops(hba);
> enable_gating:
> - if (ufshcd_is_clkscaling_supported(hba))
> - ufshcd_clk_scaling_suspend(hba, false);
> -
> hba->clk_gating.is_suspended = false;
> - hba->dev_info.b_rpm_dev_flush_capable = false;
> - ufshcd_clear_ua_wluns(hba);
> ufshcd_release(hba);
> out:
> - if (hba->dev_info.b_rpm_dev_flush_capable) {
> - schedule_delayed_work(&hba->rpm_dev_flush_recheck_work,
> - msecs_to_jiffies(RPM_DEV_FLUSH_RECHECK_WORK_DELAY_MS));
> - }
> -
> hba->pm_op_in_progress = 0;
>
> if (ret)
> @@ -8846,10 +9142,8 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> static int ufshcd_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> {
> int ret;
> - enum uic_link_state old_link_state;
>
> hba->pm_op_in_progress = 1;
> - old_link_state = hba->uic_link_state;
>
> ufshcd_hba_vreg_set_hpm(hba);
> ret = ufshcd_vreg_set_hpm(hba);
> @@ -8901,43 +9195,14 @@ static int ufshcd_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
> goto vendor_suspend;
> }
>
> - if (!ufshcd_is_ufs_dev_active(hba)) {
> - ret = ufshcd_set_dev_pwr_mode(hba, UFS_ACTIVE_PWR_MODE);
> - if (ret)
> - goto set_old_link_state;
> - }
> -
> - if (ufshcd_keep_autobkops_enabled_except_suspend(hba))
> - ufshcd_enable_auto_bkops(hba);
> - else
> - /*
> - * If BKOPs operations are urgently needed at this moment then
> - * keep auto-bkops enabled or else disable it.
> - */
> - ufshcd_urgent_bkops(hba);
> -
> - hba->clk_gating.is_suspended = false;
> -
> - if (ufshcd_is_clkscaling_supported(hba))
> - ufshcd_clk_scaling_suspend(hba, false);
> -
> /* Enable Auto-Hibernate if configured */
> ufshcd_auto_hibern8_enable(hba);
>
> - if (hba->dev_info.b_rpm_dev_flush_capable) {
> - hba->dev_info.b_rpm_dev_flush_capable = false;
> - cancel_delayed_work(&hba->rpm_dev_flush_recheck_work);
> - }
> -
> - ufshcd_clear_ua_wluns(hba);
> -
> /* Schedule clock gating in case of no access to UFS device yet */
> ufshcd_release(hba);
>
> goto out;
>
> -set_old_link_state:
> - ufshcd_link_state_transition(hba, old_link_state, 0);
> vendor_suspend:
> ufshcd_vops_suspend(hba, pm_op);
> disable_irq_and_vops_clks:
> diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
> index ee61f82..7662387 100644
> --- a/drivers/scsi/ufs/ufshcd.h
> +++ b/drivers/scsi/ufs/ufshcd.h
> @@ -72,6 +72,8 @@ enum ufs_event_type {
> UFS_EVT_LINK_STARTUP_FAIL,
> UFS_EVT_RESUME_ERR,
> UFS_EVT_SUSPEND_ERR,
> + UFS_EVT_WL_SUSP_ERR,
> + UFS_EVT_WL_RES_ERR,
>
> /* abnormal events */
> UFS_EVT_DEV_RESET,
> @@ -841,6 +843,8 @@ struct ufs_hba {
> #ifdef CONFIG_DEBUG_FS
> struct dentry *debugfs_root;
> #endif
> + bool init_done;
> + u32 luns_avail;
> };
>
> /* Returns true if clocks can be gated. Otherwise false */
> diff --git a/include/trace/events/ufs.h b/include/trace/events/ufs.h
> index e151477..d9d233b 100644
> --- a/include/trace/events/ufs.h
> +++ b/include/trace/events/ufs.h
> @@ -246,6 +246,26 @@ DEFINE_EVENT(ufshcd_template, ufshcd_init,
> int dev_state, int link_state),
> TP_ARGS(dev_name, err, usecs, dev_state, link_state));
>
> +DEFINE_EVENT(ufshcd_template, ufshcd_wl_suspend,
> + TP_PROTO(const char *dev_name, int err, s64 usecs,
> + int dev_state, int link_state),
> + TP_ARGS(dev_name, err, usecs, dev_state, link_state));
> +
> +DEFINE_EVENT(ufshcd_template, ufshcd_wl_resume,
> + TP_PROTO(const char *dev_name, int err, s64 usecs,
> + int dev_state, int link_state),
> + TP_ARGS(dev_name, err, usecs, dev_state, link_state));
> +
> +DEFINE_EVENT(ufshcd_template, ufshcd_wl_runtime_suspend,
> + TP_PROTO(const char *dev_name, int err, s64 usecs,
> + int dev_state, int link_state),
> + TP_ARGS(dev_name, err, usecs, dev_state, link_state));
> +
> +DEFINE_EVENT(ufshcd_template, ufshcd_wl_runtime_resume,
> + TP_PROTO(const char *dev_name, int err, s64 usecs,
> + int dev_state, int link_state),
> + TP_ARGS(dev_name, err, usecs, dev_state, link_state));
> +
> TRACE_EVENT(ufshcd_command,
> TP_PROTO(const char *dev_name, enum ufs_trace_str_t str_t,
> unsigned int tag, u32 doorbell, int transfer_len, u32 intr,
>