[PATCH 02/11] arm64: dts: qcom: msm8996-*: Clean up QUP and UART names
From: Konrad Dybcio
Date: Sun Feb 28 2021 - 08:10:25 EST
QUP and UART names start from 1. There are 6 QUPs and 2 UARTs
per BLSP. Let's not further confuse programmers by stating
otherwise.
Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 36 ++++++++++----------
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts | 4 +--
arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi | 2 +-
arch/arm64/boot/dts/qcom/msm8996.dtsi | 16 ++++-----
4 files changed, 29 insertions(+), 29 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index 4ed61675fdd6..7f57cdf9c753 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -41,14 +41,14 @@
/ {
aliases {
- serial0 = &blsp2_uart1;
- serial1 = &blsp2_uart2;
- serial2 = &blsp1_uart1;
- i2c0 = &blsp1_i2c2;
+ serial0 = &blsp2_uart2;
+ serial1 = &blsp2_uart3;
+ serial2 = &blsp1_uart2;
+ i2c0 = &blsp1_i2c3;
i2c1 = &blsp2_i2c1;
- i2c2 = &blsp2_i2c0;
- spi0 = &blsp1_spi0;
- spi1 = &blsp2_spi5;
+ i2c2 = &blsp2_i2c1;
+ spi0 = &blsp1_spi1;
+ spi1 = &blsp2_spi6;
};
chosen {
@@ -133,24 +133,24 @@ wlan_en: wlan-en-1-8v {
};
};
-&blsp1_i2c2 {
+&blsp1_i2c3 {
/* On Low speed expansion */
label = "LS-I2C0";
status = "okay";
};
-&blsp1_spi0 {
+&blsp1_spi1 {
/* On Low speed expansion */
label = "LS-SPI0";
status = "okay";
};
-&blsp1_uart1 {
+&blsp1_uart2 {
label = "BT-UART";
status = "okay";
pinctrl-names = "default", "sleep";
- pinctrl-0 = <&blsp1_uart1_default>;
- pinctrl-1 = <&blsp1_uart1_sleep>;
+ pinctrl-0 = <&blsp1_uart2_default>;
+ pinctrl-1 = <&blsp1_uart2_sleep>;
bluetooth {
compatible = "qcom,qca6174-bt";
@@ -162,7 +162,7 @@ bluetooth {
};
};
-&blsp2_i2c0 {
+&blsp2_i2c1 {
/* On High speed expansion */
label = "HS-I2C2";
status = "okay";
@@ -174,13 +174,13 @@ &blsp2_i2c1 {
status = "okay";
};
-&blsp2_spi5 {
+&blsp2_spi6 {
/* On High speed expansion */
label = "HS-SPI1";
status = "okay";
};
-&blsp2_uart1 {
+&blsp2_uart2 {
label = "LS-UART1";
status = "okay";
pinctrl-names = "default", "sleep";
@@ -188,7 +188,7 @@ &blsp2_uart1 {
pinctrl-1 = <&blsp2_uart2_2pins_sleep>;
};
-&blsp2_uart2 {
+&blsp2_uart3 {
label = "LS-UART0";
status = "disabled";
pinctrl-names = "default", "sleep";
@@ -424,7 +424,7 @@ config {
};
};
- blsp1_uart1_default: blsp1_uart1_default {
+ blsp1_uart2_default: blsp1_uart2_default {
mux {
pins = "gpio41", "gpio42", "gpio43", "gpio44";
function = "blsp_uart2";
@@ -437,7 +437,7 @@ config {
};
};
- blsp1_uart1_sleep: blsp1_uart1_sleep {
+ blsp1_uart2_sleep: blsp1_uart2_sleep {
mux {
pins = "gpio41", "gpio42", "gpio43", "gpio44";
function = "gpio";
diff --git a/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts b/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
index 9b55eae39e3e..4f67aa48633b 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
+++ b/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
@@ -17,7 +17,7 @@ / {
qcom,board-id = <0x00010018 0>;
aliases {
- serial0 = &blsp2_uart1;
+ serial0 = &blsp2_uart2;
};
chosen {
@@ -81,7 +81,7 @@ vph_pwr: vph-pwr-regulator {
};
};
-&blsp2_uart1 {
+&blsp2_uart2 {
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_uart2_2pins_default>;
diff --git a/arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi
index 5f46a1427f1f..1e1514e9158c 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi
@@ -7,7 +7,7 @@
/ {
aliases {
- serial0 = &blsp2_uart1;
+ serial0 = &blsp2_uart2;
};
chosen {
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 7f7e3fc03bb9..029daa2ed53e 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -2325,7 +2325,7 @@ sdhc2: sdhci@74a4900 {
bus-width = <4>;
};
- blsp1_uart1: serial@7570000 {
+ blsp1_uart2: serial@7570000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x07570000 0x1000>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
@@ -2335,7 +2335,7 @@ blsp1_uart1: serial@7570000 {
status = "disabled";
};
- blsp1_spi0: spi@7575000 {
+ blsp1_spi1: spi@7575000 {
compatible = "qcom,spi-qup-v2.2.1";
reg = <0x07575000 0x600>;
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
@@ -2350,7 +2350,7 @@ blsp1_spi0: spi@7575000 {
status = "disabled";
};
- blsp1_i2c2: i2c@7577000 {
+ blsp1_i2c3: i2c@7577000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x07577000 0x1000>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
@@ -2365,7 +2365,7 @@ blsp1_i2c2: i2c@7577000 {
status = "disabled";
};
- blsp2_uart1: serial@75b0000 {
+ blsp2_uart2: serial@75b0000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x075b0000 0x1000>;
interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
@@ -2375,7 +2375,7 @@ blsp2_uart1: serial@75b0000 {
status = "disabled";
};
- blsp2_uart2: serial@75b1000 {
+ blsp2_uart3: serial@75b1000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x075b1000 0x1000>;
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
@@ -2385,7 +2385,7 @@ blsp2_uart2: serial@75b1000 {
status = "disabled";
};
- blsp2_i2c0: i2c@75b5000 {
+ blsp2_i2c1: i2c@75b5000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x075b5000 0x1000>;
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
@@ -2400,7 +2400,7 @@ blsp2_i2c0: i2c@75b5000 {
status = "disabled";
};
- blsp2_i2c1: i2c@75b6000 {
+ blsp2_i2c2: i2c@75b6000 {
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x075b6000 0x1000>;
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
@@ -2415,7 +2415,7 @@ blsp2_i2c1: i2c@75b6000 {
status = "disabled";
};
- blsp2_spi5: spi@75ba000{
+ blsp2_spi6: spi@75ba000{
compatible = "qcom,spi-qup-v2.2.1";
reg = <0x075ba000 0x600>;
interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
--
2.30.1