Re: [PATCH v7 00/14] Tegra XHCI controller ELPG support
From: Thierry Reding
Date: Wed Mar 24 2021 - 09:32:41 EST
On Wed, Mar 24, 2021 at 01:39:32PM +0100, Thierry Reding wrote:
> On Fri, Feb 05, 2021 at 05:22:29PM +0100, Greg KH wrote:
> > On Fri, Feb 05, 2021 at 05:15:21PM +0100, Thierry Reding wrote:
> > > On Wed, Jan 20, 2021 at 03:34:00PM +0800, JC Kuo wrote:
> > > > Tegra XHCI controler can be placed in ELPG (Engine Level PowerGated)
> > > > state for power saving when all of the connected USB devices are in
> > > > suspended state. This patch series includes clk, phy and pmc changes
> > > > that are required for properly place controller in ELPG and bring
> > > > controller out of ELPG.
> > > >
> > > > JC Kuo (14):
> > > > clk: tegra: Add PLLE HW power sequencer control
> > > > clk: tegra: Don't enable PLLE HW sequencer at init
> > > > phy: tegra: xusb: Move usb3 port init for Tegra210
> > > > phy: tegra: xusb: Rearrange UPHY init on Tegra210
> > > > phy: tegra: xusb: Add Tegra210 lane_iddq operation
> > > > phy: tegra: xusb: Add sleepwalk and suspend/resume
> > > > soc/tegra: pmc: Provide USB sleepwalk register map
> > > > arm64: tegra210: XUSB PADCTL add "nvidia,pmc" prop
> > > > dt-bindings: phy: tegra-xusb: Add nvidia,pmc prop
> > > > phy: tegra: xusb: Add wake/sleepwalk for Tegra210
> > > > phy: tegra: xusb: Tegra210 host mode VBUS control
> > > > phy: tegra: xusb: Add wake/sleepwalk for Tegra186
> > > > usb: host: xhci-tegra: Unlink power domain devices
> > > > xhci: tegra: Enable ELPG for runtime/system PM
> > > >
> > > > .../phy/nvidia,tegra124-xusb-padctl.txt | 1 +
> > > > arch/arm64/boot/dts/nvidia/tegra210.dtsi | 1 +
> > > > drivers/clk/tegra/clk-pll.c | 12 -
> > > > drivers/clk/tegra/clk-tegra210.c | 53 +-
> > > > drivers/phy/tegra/xusb-tegra186.c | 558 ++++-
> > > > drivers/phy/tegra/xusb-tegra210.c | 1889 +++++++++++++----
> > > > drivers/phy/tegra/xusb.c | 92 +-
> > > > drivers/phy/tegra/xusb.h | 22 +-
> > > > drivers/soc/tegra/pmc.c | 94 +
> > > > drivers/usb/host/xhci-tegra.c | 613 ++++--
> > > > include/linux/clk/tegra.h | 4 +-
> > > > include/linux/phy/tegra/xusb.h | 10 +-
> > > > 12 files changed, 2784 insertions(+), 565 deletions(-)
> > > >
> > > > v5 "phy: tegra: xusb: tegra210: Do not reset UPHY PLL" is moved
> > > > into v6 "phy: tegra: xusb: Rearrange UPHY init on Tegra210"
> > >
> > > Mike, Stephen,
> > >
> > > could you guys take a look at the two clk patches here and give an
> > > Acked-by? There's build-time dependencies throughout the series, so it'd
> > > be good if they can all go through either the PHY or USB trees.
> > >
> > > Kishon, Greg,
> > >
> > > any comments on these patches? Unfortunately, the USB patches in this
> > > series have a build-time dependency on the PHY patches, so this should
> > > all go through one tree. Since this all culminates in the XHCI driver,
> > > merging this through the USB tree might be best, provided that Kishon
> > > provides his Acked-by on the PHY patches.
> > >
> > > Alternatively, I can create a set of branches with the correct
> > > dependencies and send out pull requests for the three subsystems if
> > > that's preferrable.
> >
> > I have no objection for the usb patches to go through your tree as they
> > are hardware-specific.
>
> Kishon,
>
> I haven't heard back from you on this yet. We missed v5.12 but I'd like
> to get this into v5.13 since it's the last missing piece to get suspend
> and resume working properly on a number of boards.
>
> Are you okay if I take this through the Tegra tree to satisfy the
> interdependencies between clk, PHY and USB patches? I've already got
> Acked-by's from the clock and USB maintainers.
>
> I want to tentatively take this into linux-next to give it a bit of soak
> time before the ARM SoC -rc6 cut-off. Please let me know if you'd prefer
> to apply these to your tree so I can back them out of the Tegra tree
> again.
Also adding Vinod for visibility and in case Kishon's too busy.
Thierry
Attachment:
signature.asc
Description: PGP signature