Re: [PATCH] staging: mt7621-pci: dt-bindings: update bindings to yaml format

From: Sergio Paracuellos
Date: Wed Apr 21 2021 - 01:45:05 EST

Next message: hch@xxxxxx: "Re: [PATCH 1/2] mm: Fix struct page layout on 32-bit systems"
Previous message: Greg KH: "Re: [PATCH] SUNRPC: Add a check for gss_release_msg"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi Rob,

On Sun, Apr 11, 2021 at 10:18 AM Sergio Paracuellos
<sergio.paracuellos@xxxxxxxxx> wrote:
>
> Update bindings for this pci controller according to the current
> device tree and driver code and prepare them to be mainlined
> porting it to the YAML format.
>
> Signed-off-by: Sergio Paracuellos <sergio.paracuellos@xxxxxxxxx>
> ---
>
> Hi Rob,
>
> Some concerns here. I was not be able to found any case similar to
> this binding where sub-nodes describing each pcie port interface
> are needed. I added them to the 'examples' directly without saying
> nothing about properties in any other place since its properties
> seems to be covered in 'pci-bus.yaml' schema definition. I don't
> know if this is the way, I have copied them to its correct future
> place in Documentation folder and check against schema and I noticed
> I am forced to add 'device_type' property in each subnode because
> schema checker complains that this is mandatory. So I have added
> it and schema is properly being validated:
>
> Before add the 'device_type' in each subnode:
> /home/sergio/staging/Documentation/devicetree/bindings/pci/mediatek,mt7621-pci.example.dt.yaml: pcie@0,0: 'device_type' is a required property
> From schema: /home/sergio/.local/lib/python3.9/site-packages/dtschema/schemas/pci/pci-bus.yaml
> /home/sergio/staging/Documentation/devicetree/bindings/pci/mediatek,mt7621-pci.example.dt.yaml: pcie@1,0: 'device_type' is a required property
> From schema: /home/sergio/.local/lib/python3.9/site-packages/dtschema/schemas/pci/pci-bus.yaml
> /home/sergio/staging/Documentation/devicetree/bindings/pci/mediatek,mt7621-pci.example.dt.yaml: pcie@2,0: 'device_type' is a required property
> From schema: /home/sergio/.local/lib/python3.9/site-packages/dtschema/schemas/pci/pci-bus.yaml
>
> After adding it:
> CHKDT Documentation/devicetree/bindings/processed-schema-examples.json
> SCHEMA Documentation/devicetree/bindings/processed-schema-examples.json
> DTEX Documentation/devicetree/bindings/pci/mediatek,mt7621-pci.example.dts
> DTC Documentation/devicetree/bindings/pci/mediatek,mt7621-pci.example.dt.yaml
> CHECK Documentation/devicetree/bindings/pci/mediatek,mt7621-pci.example.dt.yaml
>
> Looks a bit redundant and maybe I am doing somethng wrong...
>
> Thanks in advance for clarification.
>
> Best regards,
> Sergio Paracuellos

Any comments on this?? I don't know if with this subject not starting
with dt-bindings, patches end up in your review list...

Thanks in advance for your time and sorry for bothering you.

Best regards,
Sergio Paracuellos
>
>
> .../mt7621-pci/mediatek,mt7621-pci.txt | 104 -------------
> .../mt7621-pci/mediatek,mt7621-pci.yaml | 144 ++++++++++++++++++
> 2 files changed, 144 insertions(+), 104 deletions(-)
> delete mode 100644 drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
> create mode 100644 drivers/staging/mt7621-pci/mediatek,mt7621-pci.yaml
>
> diff --git a/drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt b/drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
> deleted file mode 100644
> index 327a68267309..000000000000
> --- a/drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
> +++ /dev/null
> @@ -1,104 +0,0 @@
> -MediaTek MT7621 PCIe controller
> -
> -Required properties:
> -- compatible: "mediatek,mt7621-pci"
> -- device_type: Must be "pci"
> -- reg: Base addresses and lengths of the PCIe subsys and root ports.
> -- bus-range: Range of bus numbers associated with this controller.
> -- #address-cells: Address representation for root ports (must be 3)
> -- pinctrl-names : The pin control state names.
> -- pinctrl-0: The "default" pinctrl state.
> -- #size-cells: Size representation for root ports (must be 2)
> -- ranges: Ranges for the PCI memory and I/O regions.
> -- #interrupt-cells: Must be 1
> -- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties.
> - Please refer to the standard PCI bus binding document for a more detailed
> - explanation.
> -- status: either "disabled" or "okay".
> -- resets: Must contain an entry for each entry in reset-names.
> - See ../reset/reset.txt for details.
> -- reset-names: Must be "pcie0", "pcie1", "pcieN"... based on the number of
> - root ports.
> -- clocks: Must contain an entry for each entry in clock-names.
> - See ../clocks/clock-bindings.txt for details.
> -- clock-names: Must be "pcie0", "pcie1", "pcieN"... based on the number of
> - root ports.
> -- reset-gpios: GPIO specs for the reset pins.
> -
> -In addition, the device tree node must have sub-nodes describing each PCIe port
> -interface, having the following mandatory properties:
> -
> -Required properties:
> -- reg: Only the first four bytes are used to refer to the correct bus number
> - and device number.
> -- #address-cells: Must be 3
> -- #size-cells: Must be 2
> -- ranges: Sub-ranges distributed from the PCIe controller node. An empty
> - property is sufficient.
> -- bus-range: Range of bus numbers associated with this port.
> -
> -Example for MT7621:
> -
> - pcie: pcie@1e140000 {
> - compatible = "mediatek,mt7621-pci";
> - reg = <0x1e140000 0x100 /* host-pci bridge registers */
> - 0x1e142000 0x100 /* pcie port 0 RC control registers */
> - 0x1e143000 0x100 /* pcie port 1 RC control registers */
> - 0x1e144000 0x100>; /* pcie port 2 RC control registers */
> -
> - #address-cells = <3>;
> - #size-cells = <2>;
> -
> - pinctrl-names = "default";
> - pinctrl-0 = <&pcie_pins>;
> -
> - device_type = "pci";
> -
> - bus-range = <0 255>;
> - ranges = <
> - 0x02000000 0 0x00000000 0x60000000 0 0x10000000 /* pci memory */
> - 0x01000000 0 0x00000000 0x1e160000 0 0x00010000 /* io space */
> - >;
> -
> - #interrupt-cells = <1>;
> - interrupt-map-mask = <0xF0000 0 0 1>;
> - interrupt-map = <0x10000 0 0 1 &gic GIC_SHARED 4 IRQ_TYPE_LEVEL_HIGH>,
> - <0x20000 0 0 1 &gic GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH>,
> - <0x30000 0 0 1 &gic GIC_SHARED 25 IRQ_TYPE_LEVEL_HIGH>;
> -
> - status = "disabled";
> -
> - resets = <&rstctrl 24 &rstctrl 25 &rstctrl 26>;
> - reset-names = "pcie0", "pcie1", "pcie2";
> - clocks = <&clkctrl 24 &clkctrl 25 &clkctrl 26>;
> - clock-names = "pcie0", "pcie1", "pcie2";
> -
> - reset-gpios = <&gpio 19 GPIO_ACTIVE_LOW>,
> - <&gpio 8 GPIO_ACTIVE_LOW>,
> - <&gpio 7 GPIO_ACTIVE_LOW>;
> -
> - pcie@0,0 {
> - reg = <0x0000 0 0 0 0>;
> - #address-cells = <3>;
> - #size-cells = <2>;
> - ranges;
> - bus-range = <0x00 0xff>;
> - };
> -
> - pcie@1,0 {
> - reg = <0x0800 0 0 0 0>;
> - #address-cells = <3>;
> - #size-cells = <2>;
> - ranges;
> - bus-range = <0x00 0xff>;
> - };
> -
> - pcie@2,0 {
> - reg = <0x1000 0 0 0 0>;
> - #address-cells = <3>;
> - #size-cells = <2>;
> - ranges;
> - bus-range = <0x00 0xff>;
> - };
> - };
> -
> diff --git a/drivers/staging/mt7621-pci/mediatek,mt7621-pci.yaml b/drivers/staging/mt7621-pci/mediatek,mt7621-pci.yaml
> new file mode 100644
> index 000000000000..9c1d05d929a2
> --- /dev/null
> +++ b/drivers/staging/mt7621-pci/mediatek,mt7621-pci.yaml
> @@ -0,0 +1,144 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pci/mediatek,mt7621-pci.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: MediaTek MT7621 PCIe controller
> +
> +maintainers:
> + - Sergio Paracuellos <sergio.paracuellos@xxxxxxxxx>
> +
> +description: |+
> + MediaTek MT7621 PCIe subsys supports single Root complex (RC)
> + with 3 Root Ports. Each Root Ports supports a Gen1 1-lane Link
> +
> +allOf:
> + - $ref: /schemas/pci/pci-bus.yaml#
> +
> +properties:
> + compatible:
> + const: mediatek,mt7621-pci
> +
> + reg:
> + items:
> + - description: host-pci bridge registers
> + - description: pcie port 0 RC control registers
> + - description: pcie port 1 RC control registers
> + - description: pcie port 2 RC control registers
> +
> + ranges:
> + maxItems: 2
> +
> + interrupts:
> + maxItems: 3
> +
> + resets:
> + items:
> + - description: pcie port 0 reset.
> + - description: pcie port 1 reset.
> + - description: pcie port 2 reset.
> +
> + reset-names:
> + items:
> + - const: pcie0
> + - const: pcie1
> + - const: pcie2
> +
> + clocks:
> + items:
> + - description: pcie port 0 clock.
> + - description: pcie port 1 clock.
> + - description: pcie port 2 clock.
> +
> + clock-names:
> + items:
> + - const: pcie0
> + - const: pcie1
> + - const: pcie2
> +
> + phys:
> + items:
> + - description: Dual-ported phy for pcie port 0 and 1.
> + - description: Phy for pcie port 2.
> +
> + phy-names:
> + items:
> + - const: pcie-phy0
> + - const: pcie-phy2
> +
> +required:
> + - compatible
> + - reg
> + - ranges
> + - interrupts
> + - resets
> + - reset-names
> + - clocks
> + - clock-names
> + - phys
> + - phy-names
> + - reset-gpios
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/gpio/gpio.h>
> + #include <dt-bindings/interrupt-controller/mips-gic.h>
> +
> + pcie: pcie@1e140000 {
> + compatible = "mediatek,mt7621-pci";
> + reg = <0x1e140000 0x100>,
> + <0x1e142000 0x100>,
> + <0x1e143000 0x100>,
> + <0x1e144000 0x100>;
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie_pins>;
> + device_type = "pci";
> + bus-range = <0 255>;
> + ranges = <0x02000000 0 0x00000000 0x60000000 0 0x10000000>, /* pci memory */
> + <0x01000000 0 0x00000000 0x1e160000 0 0x00010000>; /* io space */
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SHARED 4 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SHARED 25 IRQ_TYPE_LEVEL_HIGH>;
> + resets = <&rstctrl 24>, <&rstctrl 25>, <&rstctrl 26>;
> + reset-names = "pcie0", "pcie1", "pcie2";
> + clocks = <&clkctrl 24>, <&clkctrl 25>, <&clkctrl 26>;
> + clock-names = "pcie0", "pcie1", "pcie2";
> + phys = <&pcie0_phy 1>, <&pcie2_phy 0>;
> + phy-names = "pcie-phy0", "pcie-phy2";
> + reset-gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
> +
> + pcie@0,0 {
> + reg = <0x0000 0 0 0 0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> + bus-range = <0x00 0xff>;
> + };
> +
> + pcie@1,0 {
> + reg = <0x0800 0 0 0 0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> + bus-range = <0x00 0xff>;
> + };
> +
> + pcie@2,0 {
> + reg = <0x1000 0 0 0 0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> + bus-range = <0x00 0xff>;
> + };
> + };
> +...
> --
> 2.25.1
>

Next message: hch@xxxxxx: "Re: [PATCH 1/2] mm: Fix struct page layout on 32-bit systems"
Previous message: Greg KH: "Re: [PATCH] SUNRPC: Add a check for gss_release_msg"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]