Re: [PATCH 151/190] Revert "media: gspca: Check the return value of write_bridge for timeout"

[Greg Kroah-Hartman]

On Wed, Apr 21, 2021 at 03:00:26PM +0200, Greg Kroah-Hartman wrote:
> This reverts commit a21a0eb56b4e8fe4a330243af8030f890cde2283.
> 
> Commits from @umn.edu addresses have been found to be submitted in "bad
> faith" to try to test the kernel community's ability to review "known
> malicious" changes.  The result of these submissions can be found in a
> paper published at the 42nd IEEE Symposium on Security and Privacy
> entitled, "Open Source Insecurity: Stealthily Introducing
> Vulnerabilities via Hypocrite Commits" written by Qiushi Wu (University
> of Minnesota) and Kangjie Lu (University of Minnesota).
> 
> Because of this, all submissions from this group must be reverted from
> the kernel tree and will need to be re-reviewed again to determine if
> they actually are a valid fix.  Until that work is complete, remove this
> change to ensure that no problems are being introduced into the
> codebase.
> 
> Cc: Aditya Pakki <pakki001@xxxxxxx>
> Cc: Mauro Carvalho Chehab <mchehab+samsung@xxxxxxxxxx>
> Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
> ---
>  drivers/media/usb/gspca/m5602/m5602_po1030.c | 8 ++------
>  1 file changed, 2 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/media/usb/gspca/m5602/m5602_po1030.c b/drivers/media/usb/gspca/m5602/m5602_po1030.c
> index d680b777f097..7bdbb8065146 100644
> --- a/drivers/media/usb/gspca/m5602/m5602_po1030.c
> +++ b/drivers/media/usb/gspca/m5602/m5602_po1030.c
> @@ -154,7 +154,6 @@ static const struct v4l2_ctrl_config po1030_greenbal_cfg = {
>  
>  int po1030_probe(struct sd *sd)
>  {
> -	int rc = 0;
>  	u8 dev_id_h = 0, i;
>  	struct gspca_dev *gspca_dev = (struct gspca_dev *)sd;
>  
> @@ -174,14 +173,11 @@ int po1030_probe(struct sd *sd)
>  	for (i = 0; i < ARRAY_SIZE(preinit_po1030); i++) {
>  		u8 data = preinit_po1030[i][2];
>  		if (preinit_po1030[i][0] == SENSOR)
> -			rc |= m5602_write_sensor(sd,
> +			m5602_write_sensor(sd,
>  				preinit_po1030[i][1], &data, 1);
>  		else
> -			rc |= m5602_write_bridge(sd, preinit_po1030[i][1],
> -						data);
> +			m5602_write_bridge(sd, preinit_po1030[i][1], data);
>  	}
> -	if (rc < 0)
> -		return rc;
>  
>  	if (m5602_read_sensor(sd, PO1030_DEVID_H, &dev_id_h, 1))
>  		return -ENODEV;
> -- 
> 2.31.1
> 

You do not OR error values together and expect the end result to be
anything sane, so I am keeping this revert as it is incorrect.

thanks,

greg k-h