Re: [PATCH] clk: meson: g12a: fix gp0 and hifi ranges

[Jerome Brunet]

On Thu 29 Apr 2021 at 11:20, Neil Armstrong <narmstrong@xxxxxxxxxxxx> wrote:

> On 29/04/2021 11:03, Jerome Brunet wrote:
>> While some SoC samples are able to lock with a PLL factor of 55, others
>> samples can't. ATM, a minimum of 60 appears to work on all the samples
>> I have tried.
>> 
>> Even with 60, it sometimes takes a long time for the PLL to eventually
>> lock. The documentation says that the minimum rate of these PLLs DCO
>> should be 3GHz, a factor of 125. Let's use that to be on the safe side.
>> 
>> With factor range changed, the PLL seems to lock quickly (enough) so far.
>> It is still unclear if the range was the only reason for the delay.
>> 
>> Fixes: 085a4ea93d54 ("clk: meson: g12a: add peripheral clock controller")
>> Signed-off-by: Jerome Brunet <jbrunet@xxxxxxxxxxxx>
>> ---
>>  drivers/clk/meson/g12a.c | 2 +-
>>  1 file changed, 1 insertion(+), 1 deletion(-)
>> 
>> diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
>> index b080359b4645..a805bac93c11 100644
>> --- a/drivers/clk/meson/g12a.c
>> +++ b/drivers/clk/meson/g12a.c
>> @@ -1603,7 +1603,7 @@ static struct clk_regmap g12b_cpub_clk_trace = {
>>  };
>>  
>>  static const struct pll_mult_range g12a_gp0_pll_mult_range = {
>> -	.min = 55,
>> +	.min = 125,
>>  	.max = 255,
>>  };
>>  
>> 
>
> I got other issues with GP0 when trying to use it for DSI on VIM3 & VIM3L.
>
> I had to do change the following to have it lock correctly and achieve rates usable for MIPI-DSI requested bandwidth:
>
> diff --git a/drivers/clk/meson/clk-pll.c b/drivers/clk/meson/clk-pll.c
> index cde07f7ebad6..897cd6db5c0f 100644
> --- a/drivers/clk/meson/clk-pll.c
> +++ b/drivers/clk/meson/clk-pll.c
> @@ -391,9 +391,9 @@ static int meson_clk_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>                 meson_parm_write(clk->map, &pll->frac, frac);
>         }
>
> -       /* If the pll is stopped, bail out now */
> +       /* If the pll is stopped, bail out now * /
>         if (!enabled)
> -               return 0;
> +               return 0;*/

This enables the PLL everytime set_rate() is called :/

>
>         if (meson_clk_pll_enable(hw)) {
>                 pr_warn("%s: pll did not lock, trying to restore old rate %lu\n",
>
> This one is tricky, for DSI the clock rate is set with assigned-clock-rates in DT, but
> then the GP0 is seen as stopped and then the rate is never set.

Audio does the same - PLL is set and enabled afterward. This has been
working so far.

>
> When afterwards we enable the PLL, the rate set in the registers is invalid and never locks,
> this permits setting the rate in the registers even if the PLL is
> stopped.

There something to be explained here cause the register have been set
before bailing out. What is happening ? The pokes before have no effect
or are the value being reset at another point ?

I understand this need to address this concern but it does not seems
related to this particular patch.

>
> diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
> index 1b0167b8de3b..08174724a115 100644
> --- a/drivers/clk/meson/g12a.c
> +++ b/drivers/clk/meson/g12a.c
> @@ -1602,8 +1602,8 @@ static struct clk_regmap g12b_cpub_clk_trace = {
>  };
>
>  static const struct pll_mult_range g12a_gp0_pll_mult_range = {
> -       .min = 55,
> -       .max = 255,
> +       .min = 120,
> +       .max = 168,
>  };
>
> I had to change the min/max to achieve a stable and functional rate of 720MHz after the ODs.
>

How about the range provided in here ? This is range documented by AML
(3GHz < DCO < 6GHz). 168 limits would limit the rate to ~4GHz which is
way below spec and would negatively impact audio clocks.

> Neil