Re: [RFC PATCH vN net-next 2/2] net: mscc: ocelot: add support for VSC75XX SPI control

[Vladimir Oltean]

On Tue, May 04, 2021 at 02:31:34PM +0200, Andrew Lunn wrote:
> On Mon, May 03, 2021 at 10:11:27PM -0700, Colin Foster wrote:
> > Add support for control for VSC75XX chips over SPI control. Starting with the
> > VSC9959 code, this will utilize a spi bus instead of PCIe or memory-mapped IO to
> > control the chip.
> 
> Hi Colin
> 
> Please fix your subject line for the next version. vN should of been
> v1. The number is important so we can tell revisions apart.

Yes, it was my indication to use --subject-prefix="[PATCH vN net-next]",
I was expecting Colin to replace N with 1, 2, 3 etc but I didn't make
that clear enough :)

> > 
> > Signed-off-by: Colin Foster <colin.foster@xxxxxxxxxxxxxxxx>
> > ---
> >  arch/arm/boot/dts/rpi-vsc7512-spi-overlay.dts |  124 ++
> >  drivers/net/dsa/ocelot/Kconfig                |   11 +
> >  drivers/net/dsa/ocelot/Makefile               |    5 +
> >  drivers/net/dsa/ocelot/felix_vsc7512_spi.c    | 1214 +++++++++++++++++
> >  include/soc/mscc/ocelot.h                     |   15 +
> 
> Please split this patch up. The DT overlay will probably be merged via
> ARM SOC, not netdev. You also need to document the device tree
> binding, as a separate patch.
> 
> > +	fragment@3 {
> > +		target = <&spi0>;
> > +		__overlay__ {
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +			cs-gpios = <&gpio 8 1>;
> > +			status = "okay";
> > +
> > +			vsc7512: vsc7512@0{
> > +				compatible = "mscc,vsc7512";
> > +				spi-max-frequency = <250000>;
> > +				reg = <0>;
> > +
> > +				ports {
> > +					#address-cells = <1>;
> > +					#size-cells = <0>;
> > +
> > +					port@0 {
> > +						reg = <0>;
> > +						ethernet = <&ethernet>;
> > +						phy-mode = "internal";

Additionally, being a completely off-chip switch, are you sure that the
phy-mode is "internal"?

> > +						fixed-link {
> > +							speed = <1000>;
> > +							full-duplex;
> > +						};
> > +					};
> > +
> > +					port@1 {
> > +						reg = <1>;
> > +						label = "swp1";
> > +						status = "disabled";
> > +					};
> > +
> > +					port@2 {
> > +						reg = <2>;
> > +						label = "swp2";
> > +						status = "disabled";
> > +					};
> > +static void vsc7512_phylink_validate(struct ocelot *ocelot, int port,
> > +				     unsigned long *supported,
> > +				     struct phylink_link_state *state)
> > +{
> > +	struct ocelot_port *ocelot_port = ocelot->ports[port];
> > +	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = {
> > +		0,
> > +	};
> 
> This function seems out of place. Why would SPI access change what the
> ports are capable of doing? Please split this up into more
> patches. Keep the focus of this patch as being adding SPI support.

What is going on is that this is just the way in which the drivers are
structured. Colin is not really "adding SPI support" to any of the
existing DSA switches that are supported (VSC9953, VSC9959) as much as
"adding support for a new switch which happens to be controlled over
SPI" (VSC7512).
The layering is as follows:
- drivers/net/dsa/ocelot/felix_vsc7512_spi.c: deals with the most
  hardware specific SoC support. The regmap is defined here, so are the
  port capabilities.
- drivers/net/dsa/ocelot/felix.c: common integration with DSA
- drivers/net/ethernet/mscc/ocelot*.c: the SoC-independent hardware
  support.

I'm not actually sure that splitting the port PHY mode support in a
separate patch is possible while keeping functional intermediate
results. But I do agree about the rest, splitting the device tree
changes, etc.