Re: [RFC PATCH v1 2/9] net: dsa: microchip: ksz8795: add phylink support

[Vladimir Oltean]

On Wed, May 05, 2021 at 11:20:18AM +0200, Oleksij Rempel wrote:
> From: Michael Grzeschik <m.grzeschik@xxxxxxxxxxxxxx>
> 
> This patch adds the phylink support to the ksz8795 driver, since
> phylib is obsolete for dsa drivers.
> 
> Signed-off-by: Michael Grzeschik <m.grzeschik@xxxxxxxxxxxxxx>
> Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
> ---
>  drivers/net/dsa/microchip/ksz8795.c | 73 +++++++++++++++++++++++++++++
>  1 file changed, 73 insertions(+)
> 
> diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
> index 4ca352fbe81c..0ddaf2547f18 100644
> --- a/drivers/net/dsa/microchip/ksz8795.c
> +++ b/drivers/net/dsa/microchip/ksz8795.c
> @@ -18,6 +18,7 @@
>  #include <linux/micrel_phy.h>
>  #include <net/dsa.h>
>  #include <net/switchdev.h>
> +#include <linux/phylink.h>
>  
>  #include "ksz_common.h"
>  #include "ksz8795_reg.h"
> @@ -1420,11 +1421,83 @@ static int ksz8_setup(struct dsa_switch *ds)
>  	return 0;
>  }
>  
> +static int ksz_get_state(struct dsa_switch *ds, int port,
> +					  struct phylink_link_state *state)
> +{
> +	struct ksz_device *dev = ds->priv;
> +	struct ksz8 *ksz8 = dev->priv;
> +	const u8 *regs = ksz8->regs;
> +	u8 speed, link;
> +
> +	ksz_pread8(dev, port, regs[P_LINK_STATUS], &link);
> +	ksz_pread8(dev, port, regs[P_SPEED_STATUS], &speed);
> +
> +	state->link = !!(link & PORT_STAT_LINK_GOOD);
> +	if (state->link) {
> +		state->speed =
> +			(speed & PORT_STAT_SPEED_100MBIT) ? SPEED_100 : SPEED_10;
> +		state->duplex =
> +			(speed & PORT_STAT_FULL_DUPLEX) ? DUPLEX_FULL : DUPLEX_HALF;
> +	}
> +
> +	return 0;
> +}

How does the port know the speed?

> +
> +static void ksz_validate(struct dsa_switch *ds, int port,
> +			       unsigned long *supported,
> +			       struct phylink_link_state *state)

Indentation looks odd.
Also, I expect that not all KSZ PHYs to have the same validation
function, so maybe you should call this ksz8_phylink_validate.

> +{
> +	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
> +	struct ksz_device *dev = ds->priv;
> +
> +	if (port == dev->cpu_port) {
> +		if ((state->interface != PHY_INTERFACE_MODE_RMII) &&
> +		   (state->interface != PHY_INTERFACE_MODE_MII))
> +			goto unsupported;

The phylink API says that when .validate is called with state->interface
as PHY_INTERFACE_MODE_NA, you should report all supported capabilities.

> +	} else if (port > dev->port_cnt) {
> +		bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
> +		dev_err(ds->dev, "Unsupported port: %i\n", port);
> +		return;
> +	} else {
> +		if (state->interface != PHY_INTERFACE_MODE_INTERNAL)
> +			goto unsupported;
> +	}
> +
> +	/* Allow all the expected bits */
> +	phylink_set_port_modes(mask);
> +	phylink_set(mask, Autoneg);
> +
> +	phylink_set(mask, Pause);
> +	/* Silicon Errata Sheet (DS80000830A): Asym_Pause limit to port 2 */
> +	if (port || !ksz_is_ksz88x3(dev))
> +		phylink_set(mask, Asym_Pause);

The code doesn't seem to match the comment? If the switch is a KSZ88x3,
ASM_DIR will be advertised for all ports except port 0, is this what you
want?

> +
> +	/* 10M and 100M are only supported */
> +	phylink_set(mask, 10baseT_Half);
> +	phylink_set(mask, 10baseT_Full);
> +	phylink_set(mask, 100baseT_Half);
> +	phylink_set(mask, 100baseT_Full);
> +
> +	bitmap_and(supported, supported, mask,
> +		   __ETHTOOL_LINK_MODE_MASK_NBITS);
> +	bitmap_and(state->advertising, state->advertising, mask,
> +		   __ETHTOOL_LINK_MODE_MASK_NBITS);
> +
> +	return;
> +
> +unsupported:
> +	bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
> +	dev_err(ds->dev, "Unsupported interface: %d, port: %d\n",
> +		state->interface, port);

%s, phy_modes(state->interface)

> +}
> +
>  static const struct dsa_switch_ops ksz8_switch_ops = {
>  	.get_tag_protocol	= ksz8_get_tag_protocol,
>  	.setup			= ksz8_setup,
>  	.phy_read		= ksz_phy_read16,
>  	.phy_write		= ksz_phy_write16,
> +	.phylink_validate	= ksz_validate,
> +	.phylink_mac_link_state	= ksz_get_state,
>  	.phylink_mac_link_down	= ksz_mac_link_down,
>  	.port_enable		= ksz_enable_port,
>  	.get_strings		= ksz8_get_strings,
> -- 
> 2.29.2
>