Re: [Linux-stm32] [PATCH v4 4/4] i2c: stm32f4: Fix stmpe811 get xyz data timeout issue

[Patrice CHOTARD]

Hi Dillon

In order to test this patch, it's tricky to make a recent kernel running 
on stm32f429-disco as this board embeds only 8MB of SDRAM and 2MB of flash.

Can you indicates us which kernel version you are using and also the kernel config please ?

Thanks

Patrice

On 5/7/21 4:54 AM, dillon min wrote:
> Hi Pierre-Yves, Alain
> 
> Could you help to take a look?
> i really appreciate it.
> 
> Thanks,
> 
> Best Regards
> Dillon
> 
> On Mon, Mar 15, 2021 at 9:00 PM Wolfram Sang <wsa@xxxxxxxxxx> wrote:
>>
>> On Mon, Mar 15, 2021 at 08:43:54PM +0800, dillon min wrote:
>>> Hi All,
>>>
>>> Just a gentle ping.
>>
>> Pierre-Yves?
>>
>>>
>>> Regards.
>>>
>>> On Tue, Jun 9, 2020 at 9:27 PM <dillon.minfei@xxxxxxxxx> wrote:
>>>>
>>>> From: dillon min <dillon.minfei@xxxxxxxxx>
>>>>
>>>> as stm32f429's internal flash is 2Mbytes and compiled kernel
>>>> image bigger than 2Mbytes, so we have to load kernel image
>>>> to sdram on stm32f429-disco board which has 8Mbytes sdram space.
>>>>
>>>> based on above context, as you knows kernel running on external
>>>> sdram is more slower than internal flash. besides, we need read 4
>>>> bytes to get touch screen xyz(x, y, pressure) coordinate data in
>>>> stmpe811 interrupt.
>>>>
>>>> so, in stm32f4_i2c_handle_rx_done, as i2c read slower than running
>>>> in xip mode, have to adjust 'STOP/START bit set position' from last
>>>> two bytes to last one bytes. else, will get i2c timeout in reading
>>>> touch screen coordinate.
>>>>
>>>> to not take side effect, introduce IIC_LAST_BYTE_POS to support xip
>>>> kernel or has mmu platform.
>>>>
>>>> Signed-off-by: dillon min <dillon.minfei@xxxxxxxxx>
>>>> ---
>>>>
>>>> V4: indroduce 'IIC_LAST_BYTE_POS' to compatible with xipkernel boot
>>>>
>>>>  drivers/i2c/busses/i2c-stm32f4.c | 12 +++++++++---
>>>>  1 file changed, 9 insertions(+), 3 deletions(-)
>>>>
>>>> diff --git a/drivers/i2c/busses/i2c-stm32f4.c b/drivers/i2c/busses/i2c-stm32f4.c
>>>> index d6a69dfcac3f..97cf42ae7fa0 100644
>>>> --- a/drivers/i2c/busses/i2c-stm32f4.c
>>>> +++ b/drivers/i2c/busses/i2c-stm32f4.c
>>>> @@ -93,6 +93,12 @@
>>>>  #define STM32F4_I2C_MAX_FREQ           46U
>>>>  #define HZ_TO_MHZ                      1000000
>>>>
>>>> +#if !defined(CONFIG_MMU) && !defined(CONFIG_XIP_KERNEL)
>>>> +#define IIC_LAST_BYTE_POS 1
>>>> +#else
>>>> +#define IIC_LAST_BYTE_POS 2
>>>> +#endif
>>>> +
>>>>  /**
>>>>   * struct stm32f4_i2c_msg - client specific data
>>>>   * @addr: 8-bit slave addr, including r/w bit
>>>> @@ -439,7 +445,7 @@ static void stm32f4_i2c_handle_rx_done(struct stm32f4_i2c_dev *i2c_dev)
>>>>         int i;
>>>>
>>>>         switch (msg->count) {
>>>> -       case 2:
>>>> +       case IIC_LAST_BYTE_POS:
>>>>                 /*
>>>>                  * In order to correctly send the Stop or Repeated Start
>>>>                  * condition on the I2C bus, the STOP/START bit has to be set
>>>> @@ -454,7 +460,7 @@ static void stm32f4_i2c_handle_rx_done(struct stm32f4_i2c_dev *i2c_dev)
>>>>                 else
>>>>                         stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_START);
>>>>
>>>> -               for (i = 2; i > 0; i--)
>>>> +               for (i = IIC_LAST_BYTE_POS; i > 0; i--)
>>>>                         stm32f4_i2c_read_msg(i2c_dev);
>>>>
>>>>                 reg = i2c_dev->base + STM32F4_I2C_CR2;
>>>> @@ -463,7 +469,7 @@ static void stm32f4_i2c_handle_rx_done(struct stm32f4_i2c_dev *i2c_dev)
>>>>
>>>>                 complete(&i2c_dev->complete);
>>>>                 break;
>>>> -       case 3:
>>>> +       case (IIC_LAST_BYTE_POS+1):
>>>>                 /*
>>>>                  * In order to correctly generate the NACK pulse after the last
>>>>                  * received data byte, we have to enable NACK before reading N-2
>>>> --
>>>> 2.7.4
>>>>
> _______________________________________________
> Linux-stm32 mailing list
> Linux-stm32@xxxxxxxxxxxxxxxxxxxxxxxxxxxx
> https://st-md-mailman.stormreply.com/mailman/listinfo/linux-stm32
>