[PATCH 43/53] docs: PCI: acpi-info.rst: avoid using UTF-8 chars

[Mauro Carvalho Chehab]

While UTF-8 characters can be used at the Linux documentation,
the best is to use them only when ASCII doesn't offer a good replacement.
So, replace the occurences of the following UTF-8 characters:

	- U+00a0 (' '): NO-BREAK SPACE
	- U+2013 ('–'): EN DASH
	- U+2019 ('’'): RIGHT SINGLE QUOTATION MARK

Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx>
---
 Documentation/PCI/acpi-info.rst | 26 +++++++++++++-------------
 1 file changed, 13 insertions(+), 13 deletions(-)

diff --git a/Documentation/PCI/acpi-info.rst b/Documentation/PCI/acpi-info.rst
index 060217081c79..9b4b04039982 100644
--- a/Documentation/PCI/acpi-info.rst
+++ b/Documentation/PCI/acpi-info.rst
@@ -22,9 +22,9 @@ or if the device has INTx interrupts connected by platform interrupt
 controllers and a _PRT is needed to describe those connections.
 
 ACPI resource description is done via _CRS objects of devices in the ACPI
-namespace [2].   The _CRS is like a generalized PCI BAR: the OS can read
+namespace [2].   The _CRS is like a generalized PCI BAR: the OS can read
 _CRS and figure out what resource is being consumed even if it doesn't have
-a driver for the device [3].  That's important because it means an old OS
+a driver for the device [3].  That's important because it means an old OS
 can work correctly even on a system with new devices unknown to the OS.
 The new devices might not do anything, but the OS can at least make sure no
 resources conflict with them.
@@ -41,15 +41,15 @@ ACPI, that device will have a specific _HID/_CID that tells the OS what
 driver to bind to it, and the _CRS tells the OS and the driver where the
 device's registers are.
 
-PCI host bridges are PNP0A03 or PNP0A08 devices.  Their _CRS should
-describe all the address space they consume.  This includes all the windows
+PCI host bridges are PNP0A03 or PNP0A08 devices.  Their _CRS should
+describe all the address space they consume.  This includes all the windows
 they forward down to the PCI bus, as well as registers of the host bridge
-itself that are not forwarded to PCI.  The host bridge registers include
+itself that are not forwarded to PCI.  The host bridge registers include
 things like secondary/subordinate bus registers that determine the bus
 range below the bridge, window registers that describe the apertures, etc.
 These are all device-specific, non-architected things, so the only way a
 PNP0A03/PNP0A08 driver can manage them is via _PRS/_CRS/_SRS, which contain
-the device-specific details.  The host bridge registers also include ECAM
+the device-specific details.  The host bridge registers also include ECAM
 space, since it is consumed by the host bridge.
 
 ACPI defines a Consumer/Producer bit to distinguish the bridge registers
@@ -66,7 +66,7 @@ the PNP0A03/PNP0A08 device itself.  The workaround was to describe the
 bridge registers (including ECAM space) in PNP0C02 catch-all devices [6].
 With the exception of ECAM, the bridge register space is device-specific
 anyway, so the generic PNP0A03/PNP0A08 driver (pci_root.c) has no need to
-know about it.  
+know about it.  
 
 New architectures should be able to use "Consumer" Extended Address Space
 descriptors in the PNP0A03 device for bridge registers, including ECAM,
@@ -75,9 +75,9 @@ ia64 kernels assume all address space descriptors, including "Consumer"
 Extended Address Space ones, are windows, so it would not be safe to
 describe bridge registers this way on those architectures.
 
-PNP0C02 "motherboard" devices are basically a catch-all.  There's no
+PNP0C02 "motherboard" devices are basically a catch-all.  There's no
 programming model for them other than "don't use these resources for
-anything else."  So a PNP0C02 _CRS should claim any address space that is
+anything else."  So a PNP0C02 _CRS should claim any address space that is
 (1) not claimed by _CRS under any other device object in the ACPI namespace
 and (2) should not be assigned by the OS to something else.
 
@@ -125,7 +125,7 @@ address always corresponds to bus 0, even if the bus range below the bridge
     requirements of the device.  It may also call _CRS to find the current
     resource settings for the device.  Using this information, the Plug and
     Play system determines what resources the device should consume and
-    sets those resources by calling the device’s _SRS control method.
+    sets those resources by calling the device's _SRS control method.
 
     In ACPI, devices can consume resources (for example, legacy keyboards),
     provide resources (for example, a proprietary PCI bridge), or do both.
@@ -140,8 +140,8 @@ address always corresponds to bus 0, even if the bus range below the bridge
     Extended Address Space Descriptor (.4)
       General Flags: Bit [0] Consumer/Producer:
 
-        * 1 – This device consumes this resource
-        * 0 – This device produces and consumes this resource
+        * 1 - This device consumes this resource
+        * 0 - This device produces and consumes this resource
 
 [5] ACPI 6.2, sec 19.6.43:
     ResourceUsage specifies whether the Memory range is consumed by
@@ -156,7 +156,7 @@ address always corresponds to bus 0, even if the bus range below the bridge
     4.1.3) must be reserved by declaring a motherboard resource.  For most
     systems, the motherboard resource would appear at the root of the ACPI
     namespace (under \_SB) in a node with a _HID of EISAID (PNP0C02), and
-    the resources in this case should not be claimed in the root PCI bus’s
+    the resources in this case should not be claimed in the root PCI bus's
     _CRS.  The resources can optionally be returned in Int15 E820 or
     EFIGetMemoryMap as reserved memory but must always be reported through
     ACPI as a motherboard resource.
-- 
2.30.2