[PATCH v2] serial: liteuart: Add support for earlycon

[Stafford Horne]

Most litex boards using RISC-V soft cores us the sbi earlycon, however
this is not available for non RISC-V litex SoC's.  This patch enables
earlycon for liteuart which is available on all Litex SoC's making
support for earycon debugging more widely available.

Signed-off-by: Stafford Horne <shorne@xxxxxxxxx>
Cc: Florent Kermarrec <florent@xxxxxxxxxxxxxxxx>
Cc: Mateusz Holenko <mholenko@xxxxxxxxxxxx>
Cc: Joel Stanley <joel@xxxxxxxxx>
Cc: Gabriel L. Somlo <gsomlo@xxxxxxxxx>
Reviewed-and-tested-by: Gabriel Somlo <gsomlo@xxxxxxxxx>
---
Changes since v1:
 - Fixed subject
 - Fixed ifdef and config issues pointed out by Jiri
 - Use liteuart_putchar instead of early_liteuart_putc

 .../admin-guide/kernel-parameters.txt         |  5 +++++
 drivers/tty/serial/Kconfig                    |  1 +
 drivers/tty/serial/liteuart.c                 | 21 +++++++++++++++++++
 3 files changed, 27 insertions(+)

diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index 04545725f187..2d4a43af8de2 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -1084,6 +1084,11 @@
 			the driver will use only 32-bit accessors to read/write
 			the device registers.
 
+		liteuart,<addr>
+			Start an early console on a litex serial port at the
+			specified address. The serial port must already be
+			setup and configured. Options are not yet supported.
+
 		meson,<addr>
 			Start an early, polled-mode console on a meson serial
 			port at the specified address. The serial port must
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 0c4cd4a348f4..af41e534483c 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1550,6 +1550,7 @@ config SERIAL_LITEUART_CONSOLE
 	bool "LiteUART serial port console support"
 	depends on SERIAL_LITEUART=y
 	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
 	help
 	  Say 'Y' or 'M' here if you wish to use the FPGA-based LiteUART serial
 	  controller from LiteX SoC builder as the system console
diff --git a/drivers/tty/serial/liteuart.c b/drivers/tty/serial/liteuart.c
index 64842f3539e1..1b75a4bf7c56 100644
--- a/drivers/tty/serial/liteuart.c
+++ b/drivers/tty/serial/liteuart.c
@@ -370,6 +370,27 @@ static int __init liteuart_console_init(void)
 	return 0;
 }
 console_initcall(liteuart_console_init);
+
+static void early_liteuart_write(struct console *console, const char *s,
+				    unsigned int count)
+{
+	struct earlycon_device *device = console->data;
+	struct uart_port *port = &device->port;
+
+	uart_console_write(port, s, count, liteuart_putchar);
+}
+
+static int __init early_liteuart_setup(struct earlycon_device *device,
+				       const char *options)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->con->write = early_liteuart_write;
+	return 0;
+}
+
+OF_EARLYCON_DECLARE(liteuart, "litex,liteuart", early_liteuart_setup);
 #endif /* CONFIG_SERIAL_LITEUART_CONSOLE */
 
 static int __init liteuart_init(void)
-- 
2.31.1