Re: [PATCH 1/3] clk: qcom: clk-alpha-pll: add support for zonda pll

From: Vinod Koul
Date: Tue May 18 2021 - 07:32:11 EST

Next message: John Garry: "Re: [patch 5/8] perf/arm-dsu: Use irq_set_affinity()"
Previous message: Matthew Wilcox: "Re: [PATCH v10 18/33] mm/filemap: Add folio_unlock"
In reply to: Robert Foss: "Re: [PATCH 1/3] clk: qcom: clk-alpha-pll: add support for zonda pll"
Next in thread: Jonathan Marek: "Re: [PATCH 1/3] clk: qcom: clk-alpha-pll: add support for zonda pll"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On 13-05-21, 13:52, Jonathan Marek wrote:
> Ported over from the downstream driver. Will be used by SM8250 CAMCC.
>
> Signed-off-by: Jonathan Marek <jonathan@xxxxxxxx>
> ---
> drivers/clk/qcom/clk-alpha-pll.c | 245 +++++++++++++++++++++++++++++++
> drivers/clk/qcom/clk-alpha-pll.h | 6 +
> 2 files changed, 251 insertions(+)
>
> diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
> index c6eb99169ddc..7b332a8935f4 100644
> --- a/drivers/clk/qcom/clk-alpha-pll.c
> +++ b/drivers/clk/qcom/clk-alpha-pll.c
> @@ -126,6 +126,19 @@ const u8 clk_alpha_pll_regs[][PLL_OFF_MAX_REGS] = {
> [PLL_OFF_TEST_CTL_U] = 0x1c,
> [PLL_OFF_STATUS] = 0x2c,
> },
> + [CLK_ALPHA_PLL_TYPE_ZONDA] = {
> + [PLL_OFF_L_VAL] = 0x04,
> + [PLL_OFF_ALPHA_VAL] = 0x08,
> + [PLL_OFF_USER_CTL] = 0x0c,
> + [PLL_OFF_CONFIG_CTL] = 0x10,
> + [PLL_OFF_CONFIG_CTL_U] = 0x14,
> + [PLL_OFF_CONFIG_CTL_U1] = 0x18,
> + [PLL_OFF_TEST_CTL] = 0x1c,
> + [PLL_OFF_TEST_CTL_U] = 0x20,
> + [PLL_OFF_TEST_CTL_U1] = 0x24,
> + [PLL_OFF_OPMODE] = 0x28,
> + [PLL_OFF_STATUS] = 0x38,
> + },
> };
> EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
>
> @@ -162,6 +175,11 @@ EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
> #define LUCID_5LPE_PLL_LATCH_INPUT BIT(14)
> #define LUCID_5LPE_ENABLE_VOTE_RUN BIT(21)
>
> +/* ZONDA PLL specific */
> +#define ZONDA_PLL_OUT_MASK 0xf
> +#define ZONDA_STAY_IN_CFA BIT(16)
> +#define ZONDA_PLL_FREQ_LOCK_DET BIT(29)

This seems similar to ALPHA_PLL_ACK_LATCH..?

> +
> #define pll_alpha_width(p) \
> ((PLL_ALPHA_VAL_U(p) - PLL_ALPHA_VAL(p) == 4) ? \
> ALPHA_REG_BITWIDTH : ALPHA_REG_16BIT_WIDTH)
> @@ -208,6 +226,9 @@ static int wait_for_pll(struct clk_alpha_pll *pll, u32 mask, bool inverse,
> #define wait_for_pll_enable_lock(pll) \
> wait_for_pll(pll, PLL_LOCK_DET, 0, "enable")
>
> +#define wait_for_zonda_pll_freq_lock(pll) \
> + wait_for_pll(pll, ZONDA_PLL_FREQ_LOCK_DET, 0, "freq enable")
> +
> #define wait_for_pll_disable(pll) \
> wait_for_pll(pll, PLL_ACTIVE_FLAG, 1, "disable")
>
> @@ -1398,6 +1419,13 @@ const struct clk_ops clk_alpha_pll_postdiv_fabia_ops = {
> };
> EXPORT_SYMBOL_GPL(clk_alpha_pll_postdiv_fabia_ops);
>
> +const struct clk_ops clk_alpha_pll_postdiv_zonda_ops = {
> + .recalc_rate = clk_alpha_pll_postdiv_fabia_recalc_rate,
> + .round_rate = clk_alpha_pll_postdiv_fabia_round_rate,
> + .set_rate = clk_alpha_pll_postdiv_fabia_set_rate,
> +};
> +EXPORT_SYMBOL(clk_alpha_pll_postdiv_zonda_ops);

Why add one more ops when we can reuse clk_alpha_pll_postdiv_fabia_ops
for this?

> +
> /**
> * clk_lucid_pll_configure - configure the lucid pll
> *
> @@ -1777,3 +1805,220 @@ const struct clk_ops clk_alpha_pll_postdiv_lucid_5lpe_ops = {
> .set_rate = clk_lucid_5lpe_pll_postdiv_set_rate,
> };
> EXPORT_SYMBOL(clk_alpha_pll_postdiv_lucid_5lpe_ops);
> +
> +void clk_zonda_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
> + const struct alpha_pll_config *config)
> +{
> + if (config->l)
> + regmap_write(regmap, PLL_L_VAL(pll), config->l);
> +
> + if (config->alpha)
> + regmap_write(regmap, PLL_ALPHA_VAL(pll), config->alpha);
> +
> + if (config->config_ctl_val)
> + regmap_write(regmap, PLL_CONFIG_CTL(pll),
> + config->config_ctl_val);

this and below can fit in a single line and look neater

> +
> + if (config->config_ctl_hi_val)
> + regmap_write(regmap, PLL_CONFIG_CTL_U(pll),
> + config->config_ctl_hi_val);
> +
> + if (config->config_ctl_hi1_val)
> + regmap_write(regmap, PLL_CONFIG_CTL_U1(pll),
> + config->config_ctl_hi1_val);
> +
> + if (config->user_ctl_val)
> + regmap_write(regmap, PLL_USER_CTL(pll),
> + config->user_ctl_val);
> +
> + if (config->user_ctl_hi_val)
> + regmap_write(regmap, PLL_USER_CTL_U(pll),
> + config->user_ctl_hi_val);
> +
> + if (config->user_ctl_hi1_val)
> + regmap_write(regmap, PLL_USER_CTL_U1(pll),
> + config->user_ctl_hi1_val);
> +
> + if (config->test_ctl_val)
> + regmap_write(regmap, PLL_TEST_CTL(pll),
> + config->test_ctl_val);
> +
> + if (config->test_ctl_hi_val)
> + regmap_write(regmap, PLL_TEST_CTL_U(pll),
> + config->test_ctl_hi_val);
> +
> + if (config->test_ctl_hi1_val)
> + regmap_write(regmap, PLL_TEST_CTL_U1(pll),
> + config->test_ctl_hi1_val);
> +
> + regmap_update_bits(regmap, PLL_MODE(pll),
> + PLL_BYPASSNL, 0);
> +
> + /* Disable PLL output */
> + regmap_update_bits(regmap, PLL_MODE(pll), PLL_OUTCTRL, 0);
> +
> + /* Set operation mode to OFF */
> + regmap_write(regmap, PLL_OPMODE(pll), PLL_STANDBY);
> +
> + /* PLL should be in OFF mode before continuing */
> + wmb();

Why a barrier?

> +
> + /* Place the PLL in STANDBY mode */
> + regmap_update_bits(regmap, PLL_MODE(pll), PLL_RESET_N, PLL_RESET_N);
> +}
> +
> +static int clk_zonda_pll_enable(struct clk_hw *hw)
> +{
> + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
> + struct regmap *regmap = pll->clkr.regmap;
> + u32 val;
> + int ret;
> +
> + ret = regmap_read(regmap, PLL_MODE(pll), &val);
> + if (ret)
> + return ret;
> +
> + /* If in FSM mode, just vote for it */
> + if (val & PLL_VOTE_FSM_ENA) {
> + ret = clk_enable_regmap(hw);
> + if (ret)
> + return ret;
> + return wait_for_pll_enable_active(pll);
> + }
> +
> + /* Get the PLL out of bypass mode */
> + regmap_update_bits(regmap, PLL_MODE(pll), PLL_BYPASSNL, PLL_BYPASSNL);
> +
> + /*
> + * H/W requires a 1us delay between disabling the bypass and
> + * de-asserting the reset.
> + */
> + mb();
> + udelay(1);
> +
> + regmap_update_bits(regmap, PLL_MODE(pll), PLL_RESET_N, PLL_RESET_N);
> +
> + /* Set operation mode to RUN */
> + regmap_write(regmap, PLL_OPMODE(pll), PLL_RUN);
> +
> + ret = regmap_read(regmap, PLL_TEST_CTL(pll), &val);
> + if (ret)
> + return ret;
> +
> + /* If cfa mode then poll for freq lock */
> + if (val & ZONDA_STAY_IN_CFA)
> + ret = wait_for_zonda_pll_freq_lock(pll);
> + else
> + ret = wait_for_pll_enable_lock(pll);
> + if (ret)
> + return ret;
> +
> + /* Enable the PLL outputs */
> + ret = regmap_update_bits(regmap, PLL_USER_CTL(pll),
> + ZONDA_PLL_OUT_MASK, ZONDA_PLL_OUT_MASK);
> + if (ret)
> + return ret;
> +
> + /* Enable the global PLL outputs */
> + ret = regmap_update_bits(regmap, PLL_MODE(pll),
> + PLL_OUTCTRL, PLL_OUTCTRL);
> + if (ret)
> + return ret;
> +
> + /* Ensure that the write above goes through before returning. */
> + mb();
> +
> + return 0;
> +}
> +
> +static void clk_zonda_pll_disable(struct clk_hw *hw)
> +{
> + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
> + struct regmap *regmap = pll->clkr.regmap;
> + u32 val;
> + int ret;
> +
> + ret = regmap_read(regmap, PLL_MODE(pll), &val);
> + if (ret)
> + return;
> +
> + /* If in FSM mode, just unvote it */
> + if (val & PLL_VOTE_FSM_ENA) {
> + clk_disable_regmap(hw);
> + return;
> + }
> +
> + /* Disable the global PLL output */
> + ret = regmap_update_bits(regmap, PLL_MODE(pll), PLL_OUTCTRL, 0);
> +
> + /* Disable the PLL outputs */
> + regmap_update_bits(regmap, PLL_USER_CTL(pll), ZONDA_PLL_OUT_MASK, 0);
> +
> + /* Put the PLL in bypass and reset */
> + regmap_update_bits(regmap, PLL_MODE(pll), PLL_RESET_N | PLL_BYPASSNL, 0);
> +
> + /* Place the PLL mode in OFF state */
> + regmap_write(regmap, PLL_OPMODE(pll), 0x0);
> +}
> +
> +static int clk_zonda_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> + unsigned long prate)
> +{
> + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
> + unsigned long rrate;
> + u32 test_ctl_val;
> + u32 l;
> + u64 a;
> + int ret;
> +
> + rrate = alpha_pll_round_rate(rate, prate, &l, &a, ALPHA_BITWIDTH);
> +
> + ret = alpha_pll_check_rate_margin(hw, rrate, rate);
> + if (ret < 0)
> + return ret;
> +
> + regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL(pll), a);
> + regmap_write(pll->clkr.regmap, PLL_L_VAL(pll), l);
> +
> + /* Wait before polling for the frequency latch */
> + udelay(5);
> +
> + /* Read stay in cfa mode */
> + ret = regmap_read(pll->clkr.regmap, PLL_TEST_CTL(pll), &test_ctl_val);
> + if (ret)
> + return ret;
> +
> + /* If cfa mode then poll for freq lock */
> + if (test_ctl_val & ZONDA_STAY_IN_CFA)
> + ret = wait_for_zonda_pll_freq_lock(pll);
> + else
> + ret = wait_for_pll_enable_lock(pll);
> + if (ret)
> + return ret;
> +
> + /* Wait for PLL output to stabilize */
> + udelay(100);
> + return 0;
> +}
> +
> +static unsigned long
> +clk_zonda_pll_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
> +{
> + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
> + u32 l, frac;
> +
> + regmap_read(pll->clkr.regmap, PLL_L_VAL(pll), &l);
> + regmap_read(pll->clkr.regmap, PLL_ALPHA_VAL(pll), &frac);
> +
> + return alpha_pll_calc_rate(parent_rate, l, frac, ALPHA_BITWIDTH);
> +}

sounds like you could use clk_trion_pll_recalc_rate() instead

--
~Vinod

Next message: John Garry: "Re: [patch 5/8] perf/arm-dsu: Use irq_set_affinity()"
Previous message: Matthew Wilcox: "Re: [PATCH v10 18/33] mm/filemap: Add folio_unlock"
In reply to: Robert Foss: "Re: [PATCH 1/3] clk: qcom: clk-alpha-pll: add support for zonda pll"
Next in thread: Jonathan Marek: "Re: [PATCH 1/3] clk: qcom: clk-alpha-pll: add support for zonda pll"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]