Re: [RESEND PATCH V4 3/8] arm64: dts: qcom: pm7325: Add pm7325 base dts file

[skakit]

On 2021-05-18 22:12, Matthias Kaehlcke wrote:
> On Tue, May 18, 2021 at 05:16:27PM +0530, Vinod Koul wrote:
> > On 18-05-21, 11:50, satya priya wrote:
> > > Add base DTS file for pm7325 along with GPIOs and temp-alarm nodes.
> > >
> > > Signed-off-by: satya priya <skakit@xxxxxxxxxxxxxx>
> > > Reviewed-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
> > > ---
> > > Changes in RESEND V4:
> > >  - No Changes.
> > >
> > >  arch/arm64/boot/dts/qcom/pm7325.dtsi | 53 ++++++++++++++++++++++++++++++++++++
> > >  1 file changed, 53 insertions(+)
> > >  create mode 100644 arch/arm64/boot/dts/qcom/pm7325.dtsi
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/pm7325.dtsi b/arch/arm64/boot/dts/qcom/pm7325.dtsi
> > > new file mode 100644
> > > index 0000000..e7f64a9
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/qcom/pm7325.dtsi
> > > @@ -0,0 +1,53 @@
> > > +// SPDX-License-Identifier: BSD-3-Clause
> > > +// Copyright (c) 2021, The Linux Foundation. All rights reserved.
> > > +
> > > +#include <dt-bindings/interrupt-controller/irq.h>
> > > +#include <dt-bindings/spmi/spmi.h>
> > > +
> > > +&spmi_bus {
> > > +	pm7325: pmic@1 {
> > > +		compatible = "qcom,pm7325", "qcom,spmi-pmic";
> >
> > where is qcom,pm7325 documented?

> good point, I missed that one.

Actually this point was discussed during V2( 
https://lore.kernel.org/patchwork/patch/1406186/#1607321 ).
As far as I understand it is not mandatory to add "qcom,pm7325" as we 
are adding "qcom,spmi-pmic". It is just a good to have change.
I could not find the documentation for pm8350c, pmk8350 and pmr735a as 
well.

> > > +		reg = <0x1 SPMI_USID>;
> > > +		#address-cells = <1>;
> > > +		#size-cells = <0>;
> > > +
> > > +		pm7325_temp_alarm: temp-alarm@a00 {
> > > +			compatible = "qcom,spmi-temp-alarm";
> > > +			reg = <0xa00>;
> > > +			interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> > > +			#thermal-sensor-cells = <0>;
> > > +		};
> > > +
> > > +		pm7325_gpios: gpios@8800 {
> > > +			compatible = "qcom,pm7325-gpio", "qcom,spmi-gpio";
> >
> > where is qcom,pm7325-gpio documented?
>
> It's added by the 'Add GPIO support for PM7325' series
> (https://patchwork.kernel.org/project/linux-arm-msm/list/?series=481133)
>
> The binding change was acked by Rob and the code by Bjorn, so it can be
> expected to land, but it would still be good to mention the dependency
> explicitly.

The binding patch is applied now.

Thanks,
Satya Priya