Re: [RFC PATCH 2/3] mwifiex: pcie: add reset_d3cold quirk for Surface gen4+ devices

[Amey Narkhede]

On 21/05/22 03:18PM, Jonas Dreßler wrote:
> From: Tsuchiya Yuto <kitakar@xxxxxxxxx>
>
> To reset mwifiex on Surface gen4+ (Pro 4 or later gen) devices, it
> seems that putting the wifi device into D3cold is required according
> to errata.inf file on Windows installation (Windows/INF/errata.inf).
>
> This patch adds a function that performs power-cycle (put into D3cold
> then D0) and call the function at the end of reset_prepare().
>
> Note: Need to also reset the parent device (bridge) of wifi on SB1;
> it might be because the bridge of wifi always reports it's in D3hot.
> When I tried to reset only the wifi device (not touching parent), it gave
> the following error and the reset failed:
>
>     acpi device:4b: Cannot transition to power state D0 for parent in D3hot
>     mwifiex_pcie 0000:03:00.0: can't change power state from D3cold to D0 (config space inaccessible)
>
May I know how did you reset only the wifi device when you encountered
this error?

> Signed-off-by: Tsuchiya Yuto <kitakar@xxxxxxxxx>
> Signed-off-by: Jonas Dreßler <verdre@xxxxxxx>
> ---
>  drivers/net/wireless/marvell/mwifiex/pcie.c   |   7 +
>  .../wireless/marvell/mwifiex/pcie_quirks.c    | 123 ++++++++++++++++++
>  .../wireless/marvell/mwifiex/pcie_quirks.h    |   3 +
>  3 files changed, 133 insertions(+)
>
> diff --git a/drivers/net/wireless/marvell/mwifiex/pcie.c b/drivers/net/wireless/marvell/mwifiex/pcie.c
> index 02fdce926de5..d9acfea395ad 100644
> --- a/drivers/net/wireless/marvell/mwifiex/pcie.c
> +++ b/drivers/net/wireless/marvell/mwifiex/pcie.c
> @@ -528,6 +528,13 @@ static void mwifiex_pcie_reset_prepare(struct pci_dev *pdev)
>  	mwifiex_shutdown_sw(adapter);
>  	clear_bit(MWIFIEX_IFACE_WORK_DEVICE_DUMP, &card->work_flags);
>  	clear_bit(MWIFIEX_IFACE_WORK_CARD_RESET, &card->work_flags);
> +
> +	/* For Surface gen4+ devices, we need to put wifi into D3cold right
> +	 * before performing FLR
> +	 */
> +	if (card->quirks & QUIRK_FW_RST_D3COLD)
> +		mwifiex_pcie_reset_d3cold_quirk(pdev);
> +
>  	mwifiex_dbg(adapter, INFO, "%s, successful\n", __func__);
>
>  	card->pci_reset_ongoing = true;
> diff --git a/drivers/net/wireless/marvell/mwifiex/pcie_quirks.c b/drivers/net/wireless/marvell/mwifiex/pcie_quirks.c
> index 4064f99b36ba..b5f214fc1212 100644
> --- a/drivers/net/wireless/marvell/mwifiex/pcie_quirks.c
> +++ b/drivers/net/wireless/marvell/mwifiex/pcie_quirks.c
> @@ -15,6 +15,72 @@
>
>  /* quirk table based on DMI matching */
>  static const struct dmi_system_id mwifiex_quirk_table[] = {
> +	{
> +		.ident = "Surface Pro 4",
> +		.matches = {
> +			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
> +			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Pro 4"),
> +		},
> +		.driver_data = (void *)QUIRK_FW_RST_D3COLD,
> +	},
> +	{
> +		.ident = "Surface Pro 5",
> +		.matches = {
> +			/* match for SKU here due to generic product name "Surface Pro" */
> +			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
> +			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "Surface_Pro_1796"),
> +		},
> +		.driver_data = (void *)QUIRK_FW_RST_D3COLD,
> +	},
> +	{
> +		.ident = "Surface Pro 5 (LTE)",
> +		.matches = {
> +			/* match for SKU here due to generic product name "Surface Pro" */
> +			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
> +			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "Surface_Pro_1807"),
> +		},
> +		.driver_data = (void *)QUIRK_FW_RST_D3COLD,
> +	},
> +	{
> +		.ident = "Surface Pro 6",
> +		.matches = {
> +			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
> +			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Pro 6"),
> +		},
> +		.driver_data = (void *)QUIRK_FW_RST_D3COLD,
> +	},
> +	{
> +		.ident = "Surface Book 1",
> +		.matches = {
> +			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
> +			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Book"),
> +		},
> +		.driver_data = (void *)QUIRK_FW_RST_D3COLD,
> +	},
> +	{
> +		.ident = "Surface Book 2",
> +		.matches = {
> +			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
> +			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Book 2"),
> +		},
> +		.driver_data = (void *)QUIRK_FW_RST_D3COLD,
> +	},
> +	{
> +		.ident = "Surface Laptop 1",
> +		.matches = {
> +			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
> +			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Laptop"),
> +		},
> +		.driver_data = (void *)QUIRK_FW_RST_D3COLD,
> +	},
> +	{
> +		.ident = "Surface Laptop 2",
> +		.matches = {
> +			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
> +			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Laptop 2"),
> +		},
> +		.driver_data = (void *)QUIRK_FW_RST_D3COLD,
> +	},
>  	{}
>  };
>
> @@ -29,4 +95,61 @@ void mwifiex_initialize_quirks(struct pcie_service_card *card)
>
>  	if (!card->quirks)
>  		dev_info(&pdev->dev, "no quirks enabled\n");
> +	if (card->quirks & QUIRK_FW_RST_D3COLD)
> +		dev_info(&pdev->dev, "quirk reset_d3cold enabled\n");
> +}
> +
> +static void mwifiex_pcie_set_power_d3cold(struct pci_dev *pdev)
> +{
> +	dev_info(&pdev->dev, "putting into D3cold...\n");
> +
> +	pci_save_state(pdev);
> +	if (pci_is_enabled(pdev))
> +		pci_disable_device(pdev);
> +	pci_set_power_state(pdev, PCI_D3cold);
> +}
pci_set_power_state with PCI_D3cold state calls
pci_bus_set_current_state(dev->subordinate, PCI_D3cold).
Maybe this was the reason for the earlier problem you had?
Not 100% sure about this though CCing: Alex

> +
> +static int mwifiex_pcie_set_power_d0(struct pci_dev *pdev)
> +{
> +	int ret;
> +
> +	dev_info(&pdev->dev, "putting into D0...\n");
> +
> +	pci_set_power_state(pdev, PCI_D0);
> +	ret = pci_enable_device(pdev);
> +	if (ret) {
> +		dev_err(&pdev->dev, "pci_enable_device failed\n");
> +		return ret;
> +	}
> +	pci_restore_state(pdev);
On the side note just save and restore is enough in this case?
What would be the device <-> driver state after the reset as you
are calling this on parent_pdev below so that affects other
devices on bus?

Thanks,
Amey

> +
> +	return 0;
> +}
> +
> +int mwifiex_pcie_reset_d3cold_quirk(struct pci_dev *pdev)
> +{
> +	struct pci_dev *parent_pdev = pci_upstream_bridge(pdev);
> +	int ret;
> +
> +	/* Power-cycle (put into D3cold then D0) */
> +	dev_info(&pdev->dev, "Using reset_d3cold quirk to perform FW reset\n");
> +
> +	/* We need to perform power-cycle also for bridge of wifi because
> +	 * on some devices (e.g. Surface Book 1), the OS for some reasons
> +	 * can't know the real power state of the bridge.
> +	 * When tried to power-cycle only wifi, the reset failed with the
> +	 * following dmesg log:
> +	 * "Cannot transition to power state D0 for parent in D3hot".
> +	 */
> +	mwifiex_pcie_set_power_d3cold(pdev);
> +	mwifiex_pcie_set_power_d3cold(parent_pdev);
> +
> +	ret = mwifiex_pcie_set_power_d0(parent_pdev);
> +	if (ret)
> +		return ret;
> +	ret = mwifiex_pcie_set_power_d0(pdev);
> +	if (ret)
> +		return ret;
> +
> +	return 0;
>  }
> diff --git a/drivers/net/wireless/marvell/mwifiex/pcie_quirks.h b/drivers/net/wireless/marvell/mwifiex/pcie_quirks.h
> index 7a1fe3b3a61a..549093067813 100644
> --- a/drivers/net/wireless/marvell/mwifiex/pcie_quirks.h
> +++ b/drivers/net/wireless/marvell/mwifiex/pcie_quirks.h
> @@ -5,4 +5,7 @@
>
>  #include "pcie.h"
>
> +#define QUIRK_FW_RST_D3COLD	BIT(0)
> +
>  void mwifiex_initialize_quirks(struct pcie_service_card *card);
> +int mwifiex_pcie_reset_d3cold_quirk(struct pci_dev *pdev);
> --
> 2.31.1
>