Re: mtd: spinand: add spi nand mtd resume handler

[Miquel Raynal]

Hello,

<patrice.chotard@xxxxxxxxxxx> wrote on Wed, 26 May 2021 17:30:16 +0200:

> From: Christophe Kerello <christophe.kerello@xxxxxxxxxxx>

Would you mind to use "add SPI-NAND MTD resume handler" as title? (with
upper case letters)

> After power up, all SPI NAND's blocks are locked. Only read operations
> are allowed, write and erase operations are forbidden.
> The SPI NAND framework unlocks all the blocks during its initialization.
> 
> During a standby low power, the memory is powered down, losing its
> configuration.
> During the resume, the QSPI driver state is restored but the SPI NAND
> framework does not reconfigured the memory.
> 
> This patch adds spi nand mtd PM handlers for resume ops.

ditto             ^^^^^^^^^^^^

> SPI NAND resume op re-initializes SPI NAND flash to its probed state.
> 
> Signed-off-by: Christophe Kerello <christophe.kerello@xxxxxxxxxxx>
> Signed-off-by: Patrice Chotard <patrice.chotard@xxxxxxxxxxx>
> ---
>  drivers/mtd/nand/spi/core.c | 56 +++++++++++++++++++++++++++++++++++++
>  1 file changed, 56 insertions(+)
> 
> diff --git a/drivers/mtd/nand/spi/core.c b/drivers/mtd/nand/spi/core.c
> index 17f63f95f4a2..6abaf874eb3f 100644
> --- a/drivers/mtd/nand/spi/core.c
> +++ b/drivers/mtd/nand/spi/core.c
> @@ -1074,6 +1074,61 @@ static int spinand_detect(struct spinand_device *spinand)
>  	return 0;
>  }
>  
> +static void spinand_mtd_resume(struct mtd_info *mtd)
> +{
> +	struct spinand_device *spinand = mtd_to_spinand(mtd);
> +	struct nand_device *nand = mtd_to_nanddev(mtd);
> +	struct device *dev = &spinand->spimem->spi->dev;
> +	int ret, i;
> +
> +	ret = spinand_reset_op(spinand);
> +	if (ret)
> +		return;
> +
> +	ret = spinand_init_quad_enable(spinand);
> +	if (ret) {
> +		dev_err(dev,
> +			"Failed to initialize the quad part (err = %d)\n",

quad part? what about "Failed to resume the quad state" or something
alike?

> +			ret);
> +		return;
> +	}
> +
> +	ret = spinand_upd_cfg(spinand, CFG_OTP_ENABLE, 0);
> +	if (ret) {
> +		dev_err(dev,
> +			"Failed to updtae the OTP (err = %d)\n",

update

> +			ret);
> +		return;
> +	}
> +
> +	ret = spinand_manufacturer_init(spinand);
> +	if (ret) {
> +		dev_err(dev,
> +			"Failed to initialize the SPI NAND chip (err = %d)\n",
> +			ret);
> +		return;
> +	}
> +
> +	/* After power up, all blocks are locked, so unlock them here. */
> +	for (i = 0; i < nand->memorg.ntargets; i++) {
> +		ret = spinand_select_target(spinand, i);
> +		if (ret) {
> +			dev_err(dev,
> +				"Failed to select the target (err = %d)\n",
> +				ret);
> +			return;
> +		}
> +
> +		ret = spinand_lock_block(spinand, BL_ALL_UNLOCKED);
> +		if (ret) {
> +			dev_err(dev,
> +				"Failed to unlock block (err = %d)\n",
> +				ret);
> +			return;
> +		}
> +	}

I bet this would deserve a helper as this is the exact same peace of
code that is being run in spinnand_init()?

At the very least I think that spinand_ecc_enable(spinand, false);
should be called.

Ideally, a resume operation should be provided by ECC engines, but that
can be added later.

> +}
> +
>  static int spinand_init(struct spinand_device *spinand)
>  {
>  	struct device *dev = &spinand->spimem->spi->dev;
> @@ -1167,6 +1222,7 @@ static int spinand_init(struct spinand_device *spinand)
>  	mtd->_block_isreserved = spinand_mtd_block_isreserved;
>  	mtd->_erase = spinand_mtd_erase;
>  	mtd->_max_bad_blocks = nanddev_mtd_max_bad_blocks;
> +	mtd->_resume = spinand_mtd_resume;
>  
>  	if (nand->ecc.engine) {
>  		ret = mtd_ooblayout_count_freebytes(mtd);

Thanks,
Miquèl