Re: [PATCH net-next v3 1/9] net: phy: micrel: move phy reg offsets to common header

[Andrew Lunn]

> >  	switch (reg) {
> > -	case PHY_REG_CTRL:
> > +	case MII_BMCR:
> >  		ksz_pread8(dev, p, regs[P_NEG_RESTART_CTRL], &restart);
> >  		ksz_pread8(dev, p, regs[P_SPEED_STATUS], &speed);
> >  		ksz_pread8(dev, p, regs[P_FORCE_CTRL], &ctrl);
> >  		if (restart & PORT_PHY_LOOPBACK)
> > -			data |= PHY_LOOPBACK;
> > +			data |= BMCR_LOOPBACK;
> >  		if (ctrl & PORT_FORCE_100_MBIT)
> > -			data |= PHY_SPEED_100MBIT;
> > +			data |= BMCR_SPEED100;
> >  		if (ksz_is_ksz88x3(dev)) {
> >  			if ((ctrl & PORT_AUTO_NEG_ENABLE))
> > -				data |= PHY_AUTO_NEG_ENABLE;
> > +				data |= BMCR_ANENABLE;
> >  		} else {
> >  			if (!(ctrl & PORT_AUTO_NEG_DISABLE))
> > -				data |= PHY_AUTO_NEG_ENABLE;
> > +				data |= BMCR_ANENABLE;
> >  		}
> >  		if (restart & PORT_POWER_DOWN)
> > -			data |= PHY_POWER_DOWN;
> > +			data |= BMCR_PDOWN;
> >  		if (restart & PORT_AUTO_NEG_RESTART)
> > -			data |= PHY_AUTO_NEG_RESTART;
> > +			data |= BMCR_ANRESTART;
> >  		if (ctrl & PORT_FORCE_FULL_DUPLEX)
> > -			data |= PHY_FULL_DUPLEX;
> > +			data |= BMCR_FULLDPLX;
> >  		if (speed & PORT_HP_MDIX)
> > -			data |= PHY_HP_MDIX;
> > +			data |= KSZ886X_BMCR_HP_MDIX;
> >  		if (restart & PORT_FORCE_MDIX)
> > -			data |= PHY_FORCE_MDIX;
> > +			data |= KSZ886X_BMCR_FORCE_MDI;
> >  		if (restart & PORT_AUTO_MDIX_DISABLE)
> > -			data |= PHY_AUTO_MDIX_DISABLE;
> > +			data |= KSZ886X_BMCR_DISABLE_AUTO_MDIX;
> >  		if (restart & PORT_TX_DISABLE)
> > -			data |= PHY_TRANSMIT_DISABLE;
> > +			data |= KSZ886X_BMCR_DISABLE_TRANSMIT;
> >  		if (restart & PORT_LED_OFF)
> > -			data |= PHY_LED_DISABLE;
> > +			data |= KSZ886X_BMCR_DISABLE_LED;
> >  		break;
> 
> I am deeply confused as to what this function is doing. It is reading
> the 8-bit port registers P_NEG_RESTART_CTRL, P_SPEED_STATUS and
> P_FORCE_CTRL and stitching them into a 16-bit "MII_BMCR"?

Sort of. Take a look at the datasheet for the ksz8841. It has clause
22 like registers which it exports to a PHY driver. It puts MDIX
control into the bottom of the BMCR. So this DSA driver is emulating
the ksz8841 so it can share the PHY driver.

    Andrew