Re: [PATCH v3] arm64: dts: ti: k3-am65: Add support for UHS-I modes in MMCSD1 subsystem

[Jan Kiszka]

On 11.05.21 18:48, Aswath Govindraju wrote:
> UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1].
> 
> Add support by removing the no-1-8-v tag and including the voltage
> regulator device tree nodes for power cycling.
> 
> However, the 4 bit interface of AM65 SR 1.0 cannot be supported at 3.3 V or
> 1.8 V because of erratas i2025 and i2026 [2]. As the SD card is the primary
> boot mode for development usecases, continue to enable SD card and disable
> UHS-I modes in it to minimize any ageing issues happening because of
> erratas.
> 
> k3-am6528-iot2050-basic and k3-am6548-iot2050-advanced boards use S.R. 1.0
> version of AM65 SoC. Therefore, add no-1-8-v in sdhci1 device tree node of
> the common iot2050 device tree file.
> 
> [1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1
> [2] - https://www.ti.com/lit/er/sprz452e/sprz452e.pdf
> 
> Signed-off-by: Aswath Govindraju <a-govindraju@xxxxxx>
> ---
> 
> changes since v2:
> - moved the no-1-8-v tag to common iot2050 dtsi file.
> 
> changes since v1:
> - added no-1-8-v tag in sdhci1 dt nodes of k3-am6528-iot2050-basic and
>   k3-am6548-iot2050-advanced boards as they use S.R.1.0 version AM65 SoC.
> 
>  .../boot/dts/ti/k3-am65-iot2050-common.dtsi   |  1 +
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi      |  1 -
>  .../arm64/boot/dts/ti/k3-am654-base-board.dts | 33 +++++++++++++++++++
>  3 files changed, 34 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> index de763ca9251c..46cc348cd4be 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> @@ -555,6 +555,7 @@
>  	pinctrl-0 = <&main_mmc1_pins_default>;
>  	ti,driver-strength-ohm = <50>;
>  	disable-wp;
> +	no-1-8-v;
>  };
>  

Acked-by: Jan Kiszka <jan.kiszka@xxxxxxxxxxx>

Jan

>  &usb0 {
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index cb340d1b401f..632f32fce4a1 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -301,7 +301,6 @@
>  		ti,otap-del-sel = <0x2>;
>  		ti,trm-icp = <0x8>;
>  		dma-coherent;
> -		no-1-8-v;
>  	};
>  
>  	scm_conf: scm-conf@100000 {
> diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> index 9e87fb313a54..51c594b4dddb 100644
> --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> @@ -91,6 +91,38 @@
>  		#clock-cells = <0>;
>  		clock-frequency = <24000000>;
>  	};
> +
> +	evm_12v0: fixedregulator-evm12v0 {
> +		/* main supply */
> +		compatible = "regulator-fixed";
> +		regulator-name = "evm_12v0";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	vcc3v3_io: fixedregulator-vcc3v3io {
> +		/* Output of TPS54334 */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc3v3_io";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +		vin-supply = <&evm_12v0>;
> +	};
> +
> +	vdd_mmc1_sd: fixedregulator-sd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vdd_mmc1_sd";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		enable-active-high;
> +		vin-supply = <&vcc3v3_io>;
> +		gpio = <&pca9554 4 GPIO_ACTIVE_HIGH>;
> +	};
>  };
>  
>  &wkup_pmx0 {
> @@ -350,6 +382,7 @@
>   * disable sdhci1
>   */
>  &sdhci1 {
> +	vmmc-supply = <&vdd_mmc1_sd>;
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&main_mmc1_pins_default>;
>  	ti,driver-strength-ohm = <50>;
> 

-- 
Siemens AG, T RDA IOT
Corporate Competence Center Embedded Linux