Re: [PATCH 1/4] drm/panel: Add ilitek ili9341 panel driver

From: Dillon Min
Date: Mon May 31 2021 - 22:31:47 EST

Next message: Dmitry Osipenko: "[PATCH v6 01/14] regulator: core: Add regulator_sync_voltage_rdev()"
Previous message: Florian Fainelli: "Re: [PATCH 5.10 000/252] 5.10.42-rc1 review"
In reply to: Dillon Min: "Re: [PATCH 1/4] drm/panel: Add ilitek ili9341 panel driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi Patrice

On Mon, May 31, 2021 at 9:39 PM Dillon Min <dillon.minfei@xxxxxxxxx> wrote:
>
> On Mon, May 31, 2021 at 9:15 PM Patrice CHOTARD
> <patrice.chotard@xxxxxxxxxxx> wrote:
> >
> > Hi Dillon
> >
> > When trying to applying this patch using "git am --3 <patch>" i got this error :
> >
> > error: cannot convert from y to UTF-8
> > fatal: could not parse patch
> >
> > Whereas i got no similar error with the other patch 2/3 and 4.
> >
> > I find a way to apply it anyway.
>
> Sorry for the inconvenience, I will double verify the 'git am' process
> on this patch later.

I can't reproduce this on my side.

fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$ git --version
git version 2.7.4
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$ git am --3
../miss-c/v1/0001-drm-panel-Add-ilitek-ili9341-panel-driver.patch
Applying: drm/panel: Add ilitek ili9341 panel driver
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$ git am --3
../miss-c/v1/0002-i2c-stm32f4-Fix-stmpe811-get-xyz-data-timeout-issue.patch
Applying: i2c: stm32f4: Fix stmpe811 get xyz data timeout issue
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$ git am --3
../miss-c/v1/0003-clk-stm32-Fix-stm32f429-s-ltdc-driver-hang-in-set-cl.patch
Applying: clk: stm32: Fix stm32f429's ltdc driver hang in set clock rate
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$ git am --3
../miss-c/v1/0004-clk-stm32-Fix-ltdc-s-clock-turn-off-by-clk_disable_u.patch
Applying: clk: stm32: Fix ltdc's clock turn off by
clk_disable_unused() after kernel startup
fmin@fmin-OptiPlex-7060:~/work/kernel/up/linux$ git log
commit bbd74144f015b7a81d728f4c942925c74b415b97
Author: Dillon Min <dillon.minfei@xxxxxxxxx>
Date: Fri May 14 18:18:45 2021 +0800

clk: stm32: Fix ltdc's clock turn off by clk_disable_unused()
after kernel startup

stm32's clk driver register two ltdc gate clk to clk core by
clk_hw_register_gate() and clk_hw_register_composite()

first: 'stm32f429_gates[]', clk name is 'ltdc', which no user to use.
second: 'stm32f429_aux_clk[]', clk name is 'lcd-tft', used by ltdc driver

both of them point to the same offset of stm32's RCC register. after
kernel enter console, clk core turn off ltdc's clk as 'stm32f429_gates[]'
is no one to use. but, actually 'stm32f429_aux_clk[]' is in use.

Fixes: daf2d117cbca ("clk: stm32f4: Add lcd-tft clock")
Signed-off-by: Dillon Min <dillon.minfei@xxxxxxxxx>
Acked-by: Stephen Boyd <sboyd@xxxxxxxxxx>
Link: https://lore.kernel.org/linux-arm-kernel/1590564453-24499-7-git-send-email-dillon.minfei@xxxxxxxxx/

commit 9923957735ad0ae3e9da7f35f9bf83d6882499c6
Author: Dillon Min <dillon.minfei@xxxxxxxxx>
Date: Fri May 14 18:15:06 2021 +0800

clk: stm32: Fix stm32f429's ltdc driver hang in set clock rate

This is due to misuse ‘PLL_VCO_SAI' and'PLL_SAI' in clk-stm32f4.c
'PLL_SAI' is 2, 'PLL_VCO_SAI' is 7(defined in
include/dt-bindings/clock/stm32fx-clock.h).

'post_div' point to 'post_div_data[]', 'post_div->pll_num'
is PLL_I2S or PLL_SAI.

'clks[PLL_VCO_SAI]' has valid 'struct clk_hw* ' return
from stm32f4_rcc_register_pll() but, at line 1777 of
driver/clk/clk-stm32f4.c, use the 'clks[post_div->pll_num]',
equal to 'clks[PLL_SAI]', this is invalid array member at that time.

Fixes: 517633ef630e ("clk: stm32f4: Add post divisor for I2S & SAI PLLs")
Signed-off-by: Dillon Min <dillon.minfei@xxxxxxxxx>
Acked-by: Stephen Boyd <sboyd@xxxxxxxxxx>
Link: https://lore.kernel.org/linux-arm-kernel/1590564453-24499-6-git-send-email-dillon.minfei@xxxxxxxxx/

commit eeade16ed602079c9f469692a543ff00fd527a1c
Author: Dillon Min <dillon.minfei@xxxxxxxxx>
Date: Fri May 14 17:29:47 2021 +0800

i2c: stm32f4: Fix stmpe811 get xyz data timeout issue

As stm32f429's internal flash is 2Mbytes and compiled kernel
image bigger than 2Mbytes, so we have to load kernel image
to sdram on stm32f429-disco board which has 8Mbytes sdram space.

based on above context, as you knows kernel running on external
sdram is more slower than internal flash. besides, we need read 4
bytes to get touch screen xyz(x, y, pressure) coordinate data in
stmpe811 interrupt.

so, in stm32f4_i2c_handle_rx_done, as i2c read slower than running
in xip mode, have to adjust 'STOP/START bit set position' from last
two bytes to last one bytes. else, will get i2c timeout in reading
touch screen coordinate.

to not bring in side effect, introduce IIC_LAST_BYTE_POS to support xip
kernel or zImage.

Fixes: 62817fc8d282 ("i2c: stm32f4: add driver")
Link: https://lore.kernel.org/lkml/1591709203-12106-5-git-send-email-dillon.minfei@xxxxxxxxx/
Signed-off-by: Dillon Min <dillon.minfei@xxxxxxxxx>

commit 8de9a39a4f6e793f99a23fe7105a3dd7d997058b
Author: Dillon Min <dillon.minfei@xxxxxxxxx>
Date: Fri May 14 17:20:17 2021 +0800

drm/panel: Add ilitek ili9341 panel driver

This driver combine tiny/ili9341.c mipi_dbi_interface driver
with mipi_dpi_interface driver, can support ili9341 with serial
mode or parallel rgb interface mode by register configuration.

Reviewed-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
Link: https://lore.kernel.org/lkml/1590378348-8115-7-git-send-email-dillon.minfei@xxxxxxxxx/
Signed-off-by: Dillon Min <dillon.minfei@xxxxxxxxx>

commit c2131f7e73c9e9365613e323d65c7b9e5b910f56
Merge: 36c795513a88 1ab19c5de4c5
Author: Linus Torvalds <torvalds@xxxxxxxxxxxxxxxxxxxx>
Date: Mon May 31 05:57:22 2021 -1000

Merge tag 'gfs2-v5.13-rc2-fixes' of
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2

Pull gfs2 fixes from Andreas Gruenbacher:
"Various gfs2 fixes"

* tag 'gfs2-v5.13-rc2-fixes' of
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix use-after-free in gfs2_glock_shrink_scan
gfs2: Fix mmap locking for write faults
gfs2: Clean up revokes on normal withdraws
gfs2: fix a deadlock on withdraw-during-mount
gfs2: fix scheduling while atomic bug in glocks
gfs2: Fix I_NEW check in gfs2_dinode_in
gfs2: Prevent direct-I/O write fallback errors from getting lost

Best Regards
Dillon

>
> Thanks.
>
> Best Regards
> Dillon
>
> >
> > Patrice
> >
> >
> > On 5/14/21 1:02 PM, dillon.minfei@xxxxxxxxx wrote:
> > > From: Dillon Min <dillon.minfei@xxxxxxxxx>
> > >
> > > This driver combine tiny/ili9341.c mipi_dbi_interface driver
> > > with mipi_dpi_interface driver, can support ili9341 with serial
> > > mode or parallel rgb interface mode by register configuration.
> > >
> > > Reviewed-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
> > > Link: https://lore.kernel.org/lkml/1590378348-8115-7-git-send-email-dillon.minfei@xxxxxxxxx/
> > > Signed-off-by: Dillon Min <dillon.minfei@xxxxxxxxx>
> > > ---
> > > drivers/gpu/drm/panel/Kconfig | 12 +
> > > drivers/gpu/drm/panel/Makefile | 1 +
> > > drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 1285 ++++++++++++++++++++++++++
> > > 3 files changed, 1298 insertions(+)
> > > create mode 100755 drivers/gpu/drm/panel/panel-ilitek-ili9341.c
> > >
> > > diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> > > index 4894913936e9..e4babba17864 100644
> > > --- a/drivers/gpu/drm/panel/Kconfig
> > > +++ b/drivers/gpu/drm/panel/Kconfig
> > > @@ -123,6 +123,18 @@ config DRM_PANEL_ILITEK_IL9322
> > > Say Y here if you want to enable support for Ilitek IL9322
> > > QVGA (320x240) RGB, YUV and ITU-T BT.656 panels.
> > >
> > > +config DRM_PANEL_ILITEK_ILI9341
> > > + tristate "Ilitek ILI9341 240x320 QVGA panels"
> > > + depends on OF && SPI
> > > + depends on DRM_KMS_HELPER
> > > + depends on DRM_KMS_CMA_HELPER
> > > + depends on BACKLIGHT_CLASS_DEVICE
> > > + select DRM_MIPI_DBI
> > > + help
> > > + Say Y here if you want to enable support for Ilitek IL9341
> > > + QVGA (240x320) RGB panels. support serial & parallel rgb
> > > + interface.
> > > +
> > > config DRM_PANEL_ILITEK_ILI9881C
> > > tristate "Ilitek ILI9881C-based panels"
> > > depends on OF
> > > diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
> > > index cae4d976c069..0ecde184665d 100644
> > > --- a/drivers/gpu/drm/panel/Makefile
> > > +++ b/drivers/gpu/drm/panel/Makefile
> > > @@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o
> > > obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o
> > > obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o
> > > obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o
> > > +obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o
> > > obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o
> > > obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
> > > obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
> > > diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
> > > new file mode 100644
> > > index 000000000000..f84983cbb250
> > > --- /dev/null
> > > +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
> > > @@ -0,0 +1,1285 @@
> > > +// SPDX-License-Identifier: GPL-2.0-only
> > > +/*
> > > + * Ilitek ILI9341 TFT LCD drm_panel driver.
> > > + *
> > > + * This panel can be configured to support:
> > > + * - 16-bit parallel RGB interface
> > > + * - 18-bit parallel RGB interface
> > > + * - 4-line serial spi interface
> > > + *
> > > + * Copyright (C) 2020 Dillon Min <dillon.minfei@xxxxxxxxx>
> > > + * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c
> > > + */
> > > +
> > > +#include <linux/bitops.h>
> > > +#include <linux/gpio/consumer.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of_device.h>
> > > +#include <linux/regulator/consumer.h>
> > > +#include <linux/spi/spi.h>
> > > +#include <linux/delay.h>
> > > +#include <video/mipi_display.h>
> > > +#include <drm/drm_mipi_dbi.h>
> > > +#include <drm/drm_gem_framebuffer_helper.h>
> > > +#include <drm/drm_gem_cma_helper.h>
> > > +#include <drm/drm_fb_helper.h>
> > > +#include <drm/drm_gem_atomic_helper.h>
> > > +#include <drm/drm_atomic_helper.h>
> > > +
> > > +#include <drm/drm_drv.h>
> > > +#include <drm/drm_modes.h>
> > > +#include <drm/drm_panel.h>
> > > +#include <drm/drm_print.h>
> > > +
> > > +#define ILI9341_RGB_INTERFACE 0xb0 /* RGB Interface Signal Control */
> > > +#define ILI9341_FRC 0xb1 /* Frame Rate Control register */
> > > +#define ILI9341_DFC 0xb6 /* Display Function Control register */
> > > +#define ILI9341_POWER1 0xc0 /* Power Control 1 register */
> > > +#define ILI9341_POWER2 0xc1 /* Power Control 2 register */
> > > +#define ILI9341_VCOM1 0xc5 /* VCOM Control 1 register */
> > > +#define ILI9341_VCOM2 0xc7 /* VCOM Control 2 register */
> > > +#define ILI9341_POWERA 0xcb /* Power control A register */
> > > +#define ILI9341_POWERB 0xcf /* Power control B register */
> > > +#define ILI9341_PGAMMA 0xe0 /* Positive Gamma Correction register */
> > > +#define ILI9341_NGAMMA 0xe1 /* Negative Gamma Correction register */
> > > +#define ILI9341_DTCA 0xe8 /* Driver timing control A */
> > > +#define ILI9341_DTCB 0xea /* Driver timing control B */
> > > +#define ILI9341_POWER_SEQ 0xed /* Power on sequence register */
> > > +#define ILI9341_3GAMMA_EN 0xf2 /* 3 Gamma enable register */
> > > +#define ILI9341_INTERFACE 0xf6 /* Interface control register */
> > > +#define ILI9341_PRC 0xf7 /* Pump ratio control register */
> > > +#define ILI9341_ETMOD 0xb7 /* Entry mode set */
> > > +
> > > +#define ILI9341_MADCTL_BGR BIT(3)
> > > +#define ILI9341_MADCTL_MV BIT(5)
> > > +#define ILI9341_MADCTL_MX BIT(6)
> > > +#define ILI9341_MADCTL_MY BIT(7)
> > > +
> > > +
> > > +#define ILI9341_POWER_B_LEN 3
> > > +#define ILI9341_POWER_SEQ_LEN 4
> > > +#define ILI9341_DTCA_LEN 3
> > > +#define ILI9341_DTCB_LEN 2
> > > +#define ILI9341_POWER_A_LEN 5
> > > +#define ILI9341_DFC_1_LEN 2
> > > +#define ILI9341_FRC_LEN 2
> > > +#define ILI9341_VCOM_1_LEN 2
> > > +#define ILI9341_DFC_2_LEN 4
> > > +#define ILI9341_COLUMN_ADDR_LEN 4
> > > +#define ILI9341_PAGE_ADDR_LEN 4
> > > +#define ILI9341_INTERFACE_LEN 3
> > > +#define ILI9341_PGAMMA_LEN 15
> > > +#define ILI9341_NGAMMA_LEN 15
> > > +#define ILI9341_CA_LEN 3
> > > +
> > > +#define ILI9341_PIXEL_DPI_16_BITS (BIT(6)|BIT(4))
> > > +#define ILI9341_PIXEL_DPI_18_BITS (BIT(6)|BIT(5))
> > > +#define ILI9341_GAMMA_CURVE_1 BIT(0)
> > > +#define ILI9341_IF_WE_MODE BIT(0)
> > > +#define ILI9341_IF_BIG_ENDIAN 0x00
> > > +#define ILI9341_IF_DM_RGB BIT(2)
> > > +#define ILI9341_IF_DM_INTERNAL 0x00
> > > +#define ILI9341_IF_DM_VSYNC BIT(3)
> > > +#define ILI9341_IF_RM_RGB BIT(1)
> > > +#define ILI9341_IF_RIM_RGB 0x00
> > > +
> > > +#define ILI9341_COLUMN_ADDR 0x00ef
> > > +#define ILI9341_PAGE_ADDR 0x013f
> > > +
> > > +#define ILI9341_RGB_EPL BIT(0)
> > > +#define ILI9341_RGB_DPL BIT(1)
> > > +#define ILI9341_RGB_HSPL BIT(2)
> > > +#define ILI9341_RGB_VSPL BIT(3)
> > > +#define ILI9341_RGB_DE_MODE BIT(6)
> > > +#define ILI9341_RGB_DISP_PATH_MEM BIT(7)
> > > +
> > > +#define ILI9341_DBI_VCOMH_4P6V 0x23
> > > +#define ILI9341_DBI_PWR_2_DEFAULT 0x10
> > > +#define ILI9341_DBI_PRC_NORMAL 0x20
> > > +#define ILI9341_DBI_VCOM_1_VMH_4P25V 0x3e
> > > +#define ILI9341_DBI_VCOM_1_VML_1P5V 0x28
> > > +#define ILI9341_DBI_VCOM_2_DEC_58 0x86
> > > +#define ILI9341_DBI_FRC_DIVA 0x00
> > > +#define ILI9341_DBI_FRC_RTNA 0x1b
> > > +#define ILI9341_DBI_EMS_GAS BIT(0)
> > > +#define ILI9341_DBI_EMS_DTS BIT(1)
> > > +#define ILI9341_DBI_EMS_GON BIT(2)
> > > +/**
> > > + * ili9341_command - ili9341 command with optional parameter(s)
> > > + * @ili: struct ili9341
> > > + * @cmd: Command
> > > + * @seq...: Optional parameter(s)
> > > + *
> > > + * Send command to the controller.
> > > + *
> > > + * Returns:
> > > + * Zero on success, negative error code on failure.
> > > + */
> > > +#define ili9341_command(ili, cmd, seq...) \
> > > +({ \
> > > + u8 d[] = { seq }; \
> > > + _ili9341_command(ili, cmd, d, ARRAY_SIZE(d)); \
> > > +})
> > > +
> > > +/**
> > > + * struct ili9341_config - the system specific ILI9341 configuration
> > > + * @max_spi_speed: 10000000
> > > + */
> > > +struct ili9341_config {
> > > + u32 max_spi_speed;
> > > + /** @mode: the drm display mode */
> > > + const struct drm_display_mode mode;
> > > + /** @ca: TODO: need comments for this register */
> > > + u8 ca[ILI9341_CA_LEN];
> > > + /** @power_b: TODO: need comments for this register */
> > > + u8 power_b[ILI9341_POWER_B_LEN];
> > > + /** @power_seq: TODO: need comments for this register */
> > > + u8 power_seq[ILI9341_POWER_SEQ_LEN];
> > > + /** @dtca: TODO: need comments for this register */
> > > + u8 dtca[ILI9341_DTCA_LEN];
> > > + /** @dtcb: TODO: need comments for this register */
> > > + u8 dtcb[ILI9341_DTCB_LEN];
> > > + /** @power_a: TODO: need comments for this register */
> > > + u8 power_a[ILI9341_POWER_A_LEN];
> > > + /** @frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */
> > > + /*
> > > + * Formula to calculate frame frequency:
> > > + * Frame Rate=fosc/(Clocks per line x Division ratio x
> > > + * (Lines+VBP+VFP))
> > > + *
> > > + * Sets the division ratio for internal clocks of Normal mode at MCU
> > > + * interface.
> > > + *
> > > + * fosc : internal oscillator frequency
> > > + * Clocks per line : RTNA setting
> > > + * Division ratio : DIVA setting
> > > + * Lines : total driving line number
> > > + * VBP : back porch line number
> > > + * VFP : front porch line number
> > > + *
> > > + * RTNA [4:0] Frame Rate (Hz) RTNA [4:0] Frame Rate (Hz)
> > > + * 1 0 0 0 0 119 1 1 0 0 0 79
> > > + * 1 0 0 0 1 112 1 1 0 0 1 76
> > > + * 1 0 0 1 0 106 1 1 0 1 0 73
> > > + * 1 0 0 1 1 100 1 1 0 1 1 70(default)
> > > + * 1 0 1 0 0 95 1 1 1 0 0 68
> > > + * 1 0 1 0 1 90 1 1 1 0 1 65
> > > + * 1 0 1 1 0 86 1 1 1 0 1 63
> > > + * 1 0 1 1 1 83 1 1 1 1 1 61
> > > + *
> > > + * DIVA [1:0] : division ratio for internal clocks when Normal mode.
> > > + *
> > > + * DIVA [1:0] Division Ratio
> > > + * 0 0 fosc
> > > + * 0 1 fosc / 2
> > > + * 1 0 fosc / 4
> > > + * 1 1 fosc / 8
> > > + *
> > > + */
> > > + u8 frc[ILI9341_FRC_LEN];
> > > + /** @prc: TODO: need comments for this register */
> > > + u8 prc;
> > > + /** @dfc_1: B6h DISCTRL (Display Function Control) */
> > > + /* D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX
> > > + * Command 0 1 M XX 1 0 1 1 0 1 1 0 B6h
> > > + * 1st Parameter 1 1 M XX 0 0 0 0 PTG[1:0] PT[1:0] 0A
> > > + * 2nd Parameter 1 1 M XX REV GS SS SM ISC[3:0] 82
> > > + * 3rd Parameter 1 1 M XX 0 0 NL[5:0] 27
> > > + * 4th Parameter 1 1 M XX 0 0 PCDIV[5:0] XX
> > > + *
> > > + * PTG [1:0]: Set the scan mode in non-display area.
> > > + * PTG1 | PTG0 | Gate outputs in | Source outputs in | VCOM output
> > > + * non-display area | non-display area |
> > > + * 1 0 Interval scan Set with the PT[2:0] bits
> > > + *
> > > + * PT [1:0]: Determine source/VCOM output in a non-display area in the
> > > + * partial display mode.
> > > + * 1 0 AGND AGND AGND AGND
> > > + *
> > > + * REV: Select whether the liquid crystal type is normally white type
> > > + * or normally black type.
> > > + * REV Liquid crystal type
> > > + * 0 Normally black
> > > + * 1 Normally white
> > > + *
> > > + * SS: Select the shift direction of outputs from the source driver.
> > > + * SS Source Output Scan Direction
> > > + * 0 S1 -> S720
> > > + * 1 S720 -> S1
> > > + *
> > > + * GS: Sets the direction of scan by the gate driver in the range
> > > + * determined by SCN [4:0] and NL [4:0]. The scan direction
> > > + * determined by GS = 0 can be reversed by setting GS = 1.
> > > + *
> > > + * GS Gate Output Scan Direction
> > > + * 0 G1 -> G320
> > > + * 1 G320 -> G1
> > > + */
> > > + u8 dfc_1[ILI9341_DFC_1_LEN];
> > > + /** @power_1: Power Control 1 (C0h) */
> > > + /* VRH [5:0]: Set the GVDD level, which is a reference level for the
> > > + * VCOM level and the grayscale voltage level.
> > > + *
> > > + * VRH[5:0] GVDD VRH[5:0] GVDD
> > > + * 0 0 0 0 0 0 Setting prohibited 1 0 0 0 0 0 4.45 V
> > > + * 0 0 0 0 0 1 Setting prohibited 1 0 0 0 0 1 4.50 V
> > > + * 0 0 0 0 1 0 Setting prohibited 1 0 0 0 1 0 4.55 V
> > > + * 0 0 0 0 1 1 3.00 V 1 0 0 0 1 1 4.60 V
> > > + * 0 0 0 1 0 0 3.05 V 1 0 0 1 0 0 4.65 V
> > > + * 0 0 0 1 0 1 3.10 V 1 0 0 1 0 1 4.70 V
> > > + * 0 0 0 1 1 0 3.15 V 1 0 0 1 1 0 4.75 V
> > > + * 0 0 0 1 1 1 3.20 V 1 0 0 1 1 1 4.80 V
> > > + * 0 0 1 0 0 0 3.25 V 1 0 1 0 0 0 4.85 V
> > > + * 0 0 1 0 0 1 3.30 V 1 0 1 0 0 1 4.90 V
> > > + * 0 0 1 0 1 0 3.35 V 1 0 1 0 1 0 4.95 V
> > > + * 0 0 1 0 1 1 3.40 V 1 0 1 0 1 1 5.00 V
> > > + * 0 0 1 1 0 0 3.45 V 1 0 1 1 0 0 5.05 V
> > > + * 0 0 1 1 0 1 3.50 V 1 0 1 1 0 1 5.10 V
> > > + * 0 0 1 1 1 0 3.55 V 1 0 1 1 1 0 5.15 V
> > > + * 0 0 1 1 1 1 3.60 V 1 0 1 1 1 1 5.20 V
> > > + * 0 1 0 0 0 0 3.65 V 1 1 0 0 0 0 5.25 V
> > > + * 0 1 0 0 0 1 3.70 V 1 1 0 0 0 1 5.30 V
> > > + * 0 1 0 0 1 0 3.75 V 1 1 0 0 1 0 5.35 V
> > > + * 0 1 0 0 1 1 3.80 V 1 1 0 0 1 1 5.40 V
> > > + * 0 1 0 1 0 0 3.85 V 1 1 0 1 0 0 5.45 V
> > > + * 0 1 0 1 0 1 3.90 V 1 1 0 1 0 1 5.50 V
> > > + * 0 1 0 1 1 0 3.95 V 1 1 0 1 1 0 5.55 V
> > > + * 0 1 0 1 1 1 4.00 V 1 1 0 1 1 1 5.60 V
> > > + * 0 1 1 0 0 0 4.05 V 1 1 1 0 0 0 5.65 V
> > > + * 0 1 1 0 0 1 4.10 V 1 1 1 0 0 1 5.70 V
> > > + * 0 1 1 0 1 0 4.15 V 1 1 1 0 1 0 5.75 V
> > > + * 0 1 1 0 1 1 4.20 V 1 1 1 0 1 1 5.80 V
> > > + * 0 1 1 1 0 0 4.25 V 1 1 1 1 0 0 5.85 V
> > > + * 0 1 1 1 0 1 4.30 V 1 1 1 1 0 1 5.90 V
> > > + * 0 1 1 1 1 0 4.35 V 1 1 1 1 1 0 5.95 V
> > > + * 0 1 1 1 1 1 4.40 V 1 1 1 1 1 1 6.00 V
> > > + */
> > > + u8 power_1;
> > > + /** @power_2: Power Control 2 (C1h) */
> > > + /*
> > > + * BT [2:0]: Sets the factor used in the step-up circuits.
> > > + * Select the optimal step-up factor for the operating voltage. To
> > > + * reduce power consumption, set a smaller factor.
> > > + *
> > > + * BT[2:0] AVDD VGH VGL
> > > + * 0 0 0 VCI x 2 VCI x 7 VCI x 4
> > > + * 0 0 1 VCI x 3
> > > + * 0 1 0 VCI x 6 VCI x 4
> > > + * 0 1 1 VCI x 3
> > > + *
> > > + */
> > > + u8 power_2;
> > > + /** @vcom_1: VCOM Control 1(C5h) */
> > > + /*
> > > + * VMH [6:0] : Set the VCOMH voltage
> > > + *
> > > + * VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH
> > > + * 0000000 2.700 0100000 3.500 1000000 4.300 1100000 5.100
> > > + * 0000001 2.725 0100001 3.525 1000001 4.325 1100001 5.125
> > > + * 0000010 2.750 0100010 3.550 1000010 4.350 1100010 5.150
> > > + * 0000011 2.775 0100011 3.575 1000011 4.375 1100011 5.175
> > > + * 0000100 2.800 0100100 3.600 1000100 4.400 1100100 5.200
> > > + * 0000101 2.825 0100101 3.625 1000101 4.425 1100101 5.225
> > > + * 0000110 2.850 0100110 3.650 1000110 4.450 1100110 5.250
> > > + * 0000111 2.875 0100111 3.675 1000111 4.475 1100111 5.275
> > > + * 0001000 2.900 0101000 3.700 1001000 4.500 1101000 5.300
> > > + * 0001001 2.925 0101001 3.725 1001001 4.525 1101001 5.325
> > > + * 0001010 2.950 0101010 3.750 1001010 4.550 1101010 5.350
> > > + * 0001011 2.975 0101011 3.775 1001011 4.575 1101011 5.375
> > > + * 0001100 3.000 0101100 3.800 1001100 4.600 1101100 5.400
> > > + * 0001101 3.025 0101101 3.825 1001101 4.625 1101101 5.425
> > > + * 0001110 3.050 0101110 3.850 1001110 4.650 1101110 5.450
> > > + * 0001111 3.075 0101111 3.875 1001111 4.675 1101111 5.475
> > > + * 0010000 3.100 0110000 3.900 1010000 4.700 1110000 5.500
> > > + * 0010001 3.125 0110001 3.925 1010001 4.725 1110001 5.525
> > > + * 0010010 3.150 0110010 3.950 1010010 4.750 1110010 5.550
> > > + * 0010011 3.175 0110011 3.975 1010011 4.775 1110011 5.575
> > > + * 0010100 3.200 0110100 4.000 1010100 4.800 1110100 5.600
> > > + * 0010101 3.225 0110101 4.025 1010101 4.825 1110101 5.625
> > > + * 0010110 3.250 0110110 4.050 1010110 4.850 1110110 5.650
> > > + * 0010111 3.275 0110111 4.075 1010111 4.875 1110111 5.675
> > > + * 0011000 3.300 0111000 4.100 1011000 4.900 1111000 5.700
> > > + * 0011001 3.325 0111001 4.125 1011001 4.925 1111001 5.725
> > > + * 0011010 3.350 0111010 4.150 1011010 4.950 1111010 5.750
> > > + * 0011011 3.375 0111011 4.175 1011011 4.975 1111011 5.775
> > > + * 0011100 3.400 0111100 4.200 1011100 5.000 1111100 5.800
> > > + * 0011101 3.425 0111101 4.225 1011101 5.025 1111101 5.825
> > > + * 0011110 3.450 0111110 4.250 1011110 5.050 1111110 5.850
> > > + * 0011111 3.475 0111111 4.275 1011111 5.075 1111111 5.875
> > > + *
> > > + * VML[6:0] : Set the VCOML voltage
> > > + *
> > > + * VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML
> > > + * 0000000 -2.500 0100000 -1.700 1000000 -0.900 1100000 -0.100
> > > + * 0000001 -2.475 0100001 -1.675 1000001 -0.875 1100001 -0.075
> > > + * 0000010 -2.450 0100010 -1.650 1000010 -0.850 1100010 -0.050
> > > + * 0000011 -2.425 0100011 -1.625 1000011 -0.825 1100011 -0.025
> > > + * 0000100 -2.400 0100100 -1.600 1000100 -0.800 1100100 0
> > > + * 0000101 -2.375 0100101 -1.575 1000101 -0.775 1100101 Reserved
> > > + * 0000110 -2.350 0100110 -1.550 1000110 -0.750 1100110 Reserved
> > > + * 0000111 -2.325 0100111 -1.525 1000111 -0.725 1100111 Reserved
> > > + * 0001000 -2.300 0101000 -1.500 1001000 -0.700 1101000 Reserved
> > > + * 0001001 -2.275 0101001 -1.475 1001001 -0.675 1101001 Reserved
> > > + * 0001010 -2.250 0101010 -1.450 1001010 -0.650 1101010 Reserved
> > > + * 0001011 -2.225 0101011 -1.425 1001011 -0.625 1101011 Reserved
> > > + * 0001100 -2.200 0101100 -1.400 1001100 -0.600 1101100 Reserved
> > > + * 0001101 -2.175 0101101 -1.375 1001101 -0.575 1101101 Reserved
> > > + * 0001110 -2.150 0101110 -1.350 1001110 -0.550 1101110 Reserved
> > > + * 0001111 -2.125 0101111 -1.325 1001111 -0.525 1101111 Reserved
> > > + * 0010000 -2.100 0110000 -1.300 1010000 -0.500 1110000 Reserved
> > > + * 0010001 -2.075 0110001 -1.275 1010001 -0.475 1110001 Reserved
> > > + * 0010010 -2.050 0110010 -1.250 1010010 -0.450 1110010 Reserved
> > > + * 0010011 -2.025 0110011 -1.225 1010011 -0.425 1110011 Reserved
> > > + * 0010100 -2.000 0110100 -1.200 1010100 -0.400 1110100 Reserved
> > > + * 0010101 -1.975 0110101 -1.175 1010101 -0.375 1110101 Reserved
> > > + * 0010110 -1.950 0110110 -1.150 1010110 -0.350 1110110 Reserved
> > > + * 0010111 -1.925 0110111 -1.125 1010111 -0.325 1110111 Reserved
> > > + * 0011000 -1.900 0111000 -1.100 1011000 -0.300 1111000 Reserved
> > > + * 0011001 -1.875 0111001 -1.075 1011001 -0.275 1111001 Reserved
> > > + * 0011010 -1.850 0111010 -1.050 1011010 -0.250 1111010 Reserved
> > > + * 0011011 -1.825 0111011 -1.025 1011011 -0.225 1111011 Reserved
> > > + * 0011100 -1.800 0111100 -1.000 1011100 -0.200 1111100 Reserved
> > > + * 0011101 -1.775 0111101 -0.975 1011101 -0.175 1111101 Reserved
> > > + * 0011110 -1.750 0111110 -0.950 1011110 -0.150 1111110 Reserved
> > > + * 0011111 -1.725 0111111 -0.925 1011111 -0.125 1111111 Reserved
> > > + */
> > > + u8 vcom_1[ILI9341_VCOM_1_LEN];
> > > + /** @vcom_2: VCOM Control 2(C7h) */
> > > + /*
> > > + * C7h VMCTRL1 (VCOM Control 1)
> > > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX
> > > + * Command 0 1 M XX 1 1 0 0 0 1 1 1 C7h
> > > + * Parameter 1 1 M XX nVM VMF[6:0] C0
> > > + *
> > > + * nVM: nVM equals to “0” after power on reset and VCOM offset
> > > + * equals to program MTP value. When nVM set to “1”, setting
> > > + * of VMF [6:0] becomes valid and VCOMH/VCOML can be adjusted.
> > > + *
> > > + * VMF [6:0]: Set the VCOM offset voltage.
> > > + */
> > > + u8 vcom_2;
> > > + /** @address_mode: Memory Access Control (36h) */
> > > + /*
> > > + * 36h MADCTL (Memory Access Control)
> > > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX
> > > + * Command 0 1 M XX 0 0 1 1 0 1 1 0 36h
> > > + * Parameter 1 1 M XX MY MX MV ML BGR MH 0 0 00
> > > + *
> > > + * This command defines read/write scanning direction of frame memory.
> > > + * This command makes no change on the other driver status.
> > > + *
> > > + * Bit Name Description
> > > + * MY Row Address Order
> > > + * MX Column Address Order
> > > + * MV Row / Column Exchange These 3 bits control MCU to memory
> > > + * write/read direction.
> > > + * ML Vertical Refresh Order LCD vertical refresh direction control.
> > > + * BGR RGB-BGR Order Color selector switch control
> > > + * (0=RGB color filter panel, 1=BGR
> > > + * color filter panel)
> > > + * MH Horizontal Refresh ORDER LCD horizontal refreshing
> > > + * direction control.
> > > + *
> > > + * Note: When BGR bit is changed, the new setting is active
> > > + * immediately without update the content in Frame Memory again.
> > > + *
> > > + */
> > > + u8 address_mode;
> > > + /** @g3amma_en: TODO: need comments for this register */
> > > + u8 g3amma_en;
> > > + /** @rgb_interface: RGB Interface Signal Control (B0h) */
> > > + /*
> > > + * B0h IFMODE (Interface Mode Control)
> > > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX
> > > + * Command 0 1 M XX 1 0 1 1 0 0 0 0 B0h
> > > + * Parameter 1 1 M XX ByPass_MODE RCM[1] RCM[0] 0 VSPL HSPL DPL EPL 40
> > > + *
> > > + * Sets the operation status of the display interface. The setting
> > > + * becomes effective as soon as the command is received.
> > > + * EPL: DE polarity (“0”= High enable for RGB interface, “1”= Low
> > > + * enable for RGB interface)
> > > + *
> > > + * DPL: DOTCLK polarity set (“0”= data fetched at the rising time,
> > > + * “1”= data fetched at the falling time)
> > > + *
> > > + * HSPL: HSYNC polarity (“0”= Low level sync clock, “1”= High
> > > + * level sync clock)
> > > + *
> > > + * VSPL: VSYNC polarity (“0”= Low level sync clock, “1”= High
> > > + * level sync clock)
> > > + *
> > > + * RCM [1:0]: RGB interface selection (refer to the RGB interface
> > > + * section).
> > > + *
> > > + * ByPass_MODE: Select display data path whether Memory or Direct to
> > > + * Shift register when RGB Interface is used.
> > > + *
> > > + * ByPass_MODE Display Data Path
> > > + * 0 Direct to Shift Register (default)
> > > + * 1 Memory
> > > + */
> > > + u8 rgb_interface;
> > > + /** @dfc_2: refer to dfc_1 */
> > > + u8 dfc_2[ILI9341_DFC_2_LEN];
> > > + /** @column_addr: Column Address Set (2Ah) */
> > > + /* This command is used to define area of frame memory where MCU can
> > > + * access. This command makes no change on the
> > > + * other driver status. The values of SC [15:0] and EC [15:0] are
> > > + * referred when RAMWR command comes. Each value
> > > + * represents one column line in the Frame Memory.
> > > + */
> > > + u8 column_addr[ILI9341_COLUMN_ADDR_LEN];
> > > + /** @page_addr: Page Address Set (2Bh) */
> > > + /* This command is used to define area of frame memory where MCU can
> > > + * access. This command makes no change on the
> > > + * other driver status. The values of SP [15:0] and EP [15:0] are
> > > + * referred when RAMWR command comes. Each value
> > > + * represents one Page line in the Frame Memory.
> > > + */
> > > + u8 page_addr[ILI9341_PAGE_ADDR_LEN];
> > > + /** @interface: Interface Control (F6h) */
> > > + /*
> > > + * F6h IFCTL (16bits Data Format Selection)
> > > + * D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX
> > > + * Command 0 1 M XX 1 1 1 1 0 1 1 0 F6h
> > > + * 1stParameter 1 1 M XX MY MX MV
> > > + * _EOR _EOR _EOR 0 BGR_EOR 0 0 WE MODE 01
> > > + * 2ndParameter 1 1 M XX 0 0 EPF[1] EPF[0] 0 0 MDT[1] MDT[0] 00
> > > + * 3rdParameter 1 1 M XX 0 0 ENDIAN 0 DM[1] DM[0] RM RIM 00
> > > + *
> > > + */
> > > + u8 interface[ILI9341_INTERFACE_LEN];
> > > + /** @pixel_format: This command sets the pixel format for the RGB image data used by */
> > > + /* the interface. DPI [2:0] is the pixel format select of RGB
> > > + * interface and DBI [2:0] is the pixel format of MCU interface. If a
> > > + * particular interface, either RGB interface or MCU interface, is
> > > + * not used then the corresponding bits in the parameter are ignored.
> > > + * The pixel format is shown in the table below.
> > > + *
> > > + * DPI[2:0] RGB Interface Format DBI[2:0] MCU Interface Format
> > > + * 0 0 0 Reserved 0 0 0 Reserved
> > > + * 0 0 1 Reserved 0 0 1 Reserved
> > > + * 0 1 0 Reserved 0 1 0 Reserved
> > > + * 0 1 1 Reserved 0 1 1 Reserved
> > > + * 1 0 0 Reserved 1 0 0 Reserved
> > > + * 1 0 1 16 bits / pixel 1 0 1 16 bits / pixel
> > > + * 1 1 0 18 bits / pixel 1 1 0 18 bits / pixel
> > > + * 1 1 1 Reserved 1 1 1 Reserved
> > > + *
> > > + */
> > > + u8 pixel_format;
> > > + /** @gamma_curve: This command is used to select the desired Gamma curve for the */
> > > + /* current display. A maximum of 4 fixed gamma curves can
> > > + * be selected. The curve is selected by setting the appropriate bit
> > > + * in the parameter as described in the Table:
> > > + *
> > > + * GC [7:0] Curve Selected
> > > + * 01h Gamma curve 1 (G2.2)
> > > + * 02h ---
> > > + * 04h ---
> > > + * 08h ---
> > > + */
> > > + u8 gamma_curve;
> > > + /** @pgamma: Positive Gamma Correction (E0h) */
> > > + /*
> > > + * Set the gray scale voltage to adjust the gamma characteristics of
> > > + * the TFT panel.
> > > + */
> > > + u8 pgamma[ILI9341_PGAMMA_LEN];
> > > + /** @ngamma: Negative Gamma Correction (E1h) */
> > > + /*
> > > + * Set the gray scale voltage to adjust the gamma characteristics of
> > > + * the TFT panel.
> > > + */
> > > + u8 ngamma[ILI9341_NGAMMA_LEN];
> > > +};
> > > +
> > > +struct ili9341 {
> > > + struct device *dev;
> > > + const struct ili9341_config *conf;
> > > + struct drm_panel panel;
> > > + struct gpio_desc *reset_gpio;
> > > + struct gpio_desc *dc_gpio;
> > > + u32 max_spi_speed;
> > > + struct regulator *vcc;
> > > +};
> > > +
> > > +/*
> > > + * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller
> > > + */
> > > +static const struct ili9341_config ili9341_stm32f429_disco_data = {
> > > + .max_spi_speed = 10000000,
> > > + .mode = {
> > > + .clock = 6100,
> > > + .hdisplay = 240,
> > > + .hsync_start = 240 + 10,/* hfp 10 */
> > > + .hsync_end = 240 + 10 + 10,/* hsync 10 */
> > > + .htotal = 240 + 10 + 10 + 20,/* hbp 20 */
> > > + .vdisplay = 320,
> > > + .vsync_start = 320 + 4,/* vfp 4 */
> > > + .vsync_end = 320 + 4 + 2,/* vsync 2 */
> > > + .vtotal = 320 + 4 + 2 + 2,/* vbp 2 */
> > > + .flags = 0,
> > > + .width_mm = 65,
> > > + .height_mm = 50,
> > > + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
> > > + },
> > > + /* TODO: need comments for this register */
> > > + .ca = {0xc3, 0x08, 0x50},
> > > + /* TODO: need comments for this register */
> > > + .power_b = {0x00, 0xc1, 0x30},
> > > + /* TODO: need comments for this register */
> > > + .power_seq = {0x64, 0x03, 0x12, 0x81},
> > > + /* TODO: need comments for this register */
> > > + .dtca = {0x85, 0x00, 0x78},
> > > + /* TODO: need comments for this register */
> > > + .power_a = {0x39, 0x2c, 0x00, 0x34, 0x02},
> > > + /* TODO: need comments for this register */
> > > + .prc = 0x20,
> > > + /* TODO: need comments for this register */
> > > + .dtcb = {0x00, 0x00},
> > > + /* 0x00 fosc, 0x1b 70hz */
> > > + .frc = {0x00, 0x1b},
> > > + /* 0x0a Interval scan, AGND AGND AGND AGND
> > > + * 0xa2 Normally white, G1 -> G320, S720 -> S1,
> > > + * Scan Cycle 5 frames,85ms
> > > + */
> > > + .dfc_1 = {0x0a, 0xa2},
> > > + /* 0x10 3.65v */
> > > + .power_1 = 0x10,
> > > + /* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */
> > > + .power_2 = 0x10,
> > > + /* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/
> > > + .vcom_1 = {0x45, 0x15},
> > > + /* 0x90 offset voltage, VMH-48, VML-48 */
> > > + .vcom_2 = 0x90,
> > > + /* 0xc8 Row Address Order, Column Address Order
> > > + * BGR 1
> > > + */
> > > + .address_mode = 0xc8,
> > > + .g3amma_en = 0x00,
> > > + /* 0xc2
> > > + * Display Data Path: Memory
> > > + * RGB: DE mode
> > > + * DOTCLK polarity set (data fetched at the falling time)
> > > + */
> > > + .rgb_interface = ILI9341_RGB_DISP_PATH_MEM |
> > > + ILI9341_RGB_DE_MODE |
> > > + ILI9341_RGB_DPL,
> > > + /*
> > > + * 0x0a
> > > + * Gate outputs in non-display area: Interval scan
> > > + * Determine source/VCOM output in a non-display area in the partial
> > > + * display mode: AGND AGND AGND AGND
> > > + *
> > > + * 0xa7
> > > + * Scan Cycle: 15 frames
> > > + * fFLM = 60Hz: 255ms
> > > + * Liquid crystal type: Normally white
> > > + * Gate Output Scan Direction: G1 -> G320
> > > + * Source Output Scan Direction: S720 -> S1
> > > + *
> > > + * 0x27
> > > + * LCD Driver Line: 320 lines
> > > + *
> > > + * 0x04
> > > + * PCDIV: 4
> > > + */
> > > + .dfc_2 = {0x0a, 0xa7, 0x27, 0x04},
> > > + /* column address: 240 */
> > > + .column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff,
> > > + ILI9341_COLUMN_ADDR & 0xff},
> > > + /* page address: 320 */
> > > + .page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff,
> > > + ILI9341_PAGE_ADDR & 0xff},
> > > + /* Memory write control: When the transfer number of data exceeds
> > > + * (EC-SC+1)*(EP-SP+1), the column and page number will be
> > > + * reset, and the exceeding data will be written into the following
> > > + * column and page.
> > > + * Display Operation Mode: RGB Interface Mode
> > > + * Interface for RAM Access: RGB interface
> > > + * 16- bit RGB interface (1 transfer/pixel)
> > > + */
> > > + .interface = {ILI9341_IF_WE_MODE, 0x00,
> > > + ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB},
> > > + /* DPI: 16 bits / pixel */
> > > + .pixel_format = ILI9341_PIXEL_DPI_16_BITS,
> > > + /* Curve Selected: Gamma curve 1 (G2.2) */
> > > + .gamma_curve = ILI9341_GAMMA_CURVE_1,
> > > + .pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e,
> > > + 0x09, 0x4e, 0x78, 0x3c, 0x09,
> > > + 0x13, 0x05, 0x17, 0x11, 0x00},
> > > + .ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11,
> > > + 0x07, 0x31, 0x33, 0x42, 0x05,
> > > + 0x0c, 0x0a, 0x28, 0x2f, 0x0f},
> > > +};
> > > +
> > > +static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel)
> > > +{
> > > + return container_of(panel, struct ili9341, panel);
> > > +}
> > > +
> > > +static int ili9341_spi_transfer(struct spi_device *spi, u32 speed_hz,
> > > + u8 bpw, const void *buf, size_t len)
> > > +{
> > > + size_t max_chunk = spi_max_transfer_size(spi);
> > > + struct spi_transfer tr = {
> > > + .bits_per_word = bpw,
> > > + .speed_hz = speed_hz,
> > > + .len = len,
> > > + };
> > > + struct spi_message m;
> > > + size_t chunk;
> > > + int ret;
> > > +
> > > + spi_message_init_with_transfers(&m, &tr, 1);
> > > +
> > > + while (len) {
> > > + chunk = min(len, max_chunk);
> > > +
> > > + tr.tx_buf = buf;
> > > + tr.len = chunk;
> > > + buf += chunk;
> > > + len -= chunk;
> > > +
> > > + ret = spi_sync(spi, &m);
> > > + if (ret) {
> > > + dev_err(&spi->dev, "spi_sync error: %d\n", ret);
> > > + return ret;
> > > + }
> > > + }
> > > + return 0;
> > > +}
> > > +
> > > +static int _ili9341_command(struct ili9341 *ili, u8 cmd, const void *data,
> > > + size_t count)
> > > +{
> > > + struct spi_device *spi = to_spi_device(ili->dev);
> > > + int ret = 0;
> > > +
> > > + gpiod_set_value_cansleep(ili->dc_gpio, 0);
> > > +
> > > + ret = ili9341_spi_transfer(spi, ili->max_spi_speed, 8,
> > > + (const void *)&cmd, 1);
> > > + if (ret || data == NULL || count == 0) {
> > > + return ret;
> > > + }
> > > +
> > > + gpiod_set_value_cansleep(ili->dc_gpio, 1);
> > > +
> > > + return ili9341_spi_transfer(spi, ili->max_spi_speed, 8,
> > > + data, count);
> > > +}
> > > +
> > > +static int ili9341_dpi_init(struct ili9341 *ili)
> > > +{
> > > + int ret;
> > > + ret = _ili9341_command(ili, 0xca,
> > > + ili->conf->ca,
> > > + ILI9341_CA_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_POWERB,
> > > + ili->conf->power_b,
> > > + ILI9341_POWER_B_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_POWER_SEQ,
> > > + ili->conf->power_seq,
> > > + ILI9341_POWER_SEQ_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_DTCA,
> > > + ili->conf->dtca,
> > > + ILI9341_DTCA_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_POWERA,
> > > + ili->conf->power_a,
> > > + ILI9341_POWER_A_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_PRC,
> > > + &ili->conf->prc,
> > > + 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_DTCB,
> > > + ili->conf->dtcb,
> > > + ILI9341_DTCB_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_FRC,
> > > + ili->conf->frc,
> > > + ILI9341_FRC_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_DFC,
> > > + ili->conf->dfc_1,
> > > + ILI9341_DFC_1_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_POWER1,
> > > + &ili->conf->power_1,
> > > + 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_POWER2,
> > > + &ili->conf->power_2,
> > > + 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_VCOM1,
> > > + ili->conf->vcom_1,
> > > + ILI9341_VCOM_1_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_VCOM2,
> > > + &ili->conf->vcom_2,
> > > + 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, MIPI_DCS_SET_ADDRESS_MODE,
> > > + &ili->conf->address_mode,
> > > + 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_3GAMMA_EN,
> > > + &ili->conf->g3amma_en,
> > > + 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_RGB_INTERFACE,
> > > + &ili->conf->rgb_interface,
> > > + 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_DFC,
> > > + ili->conf->dfc_2,
> > > + ILI9341_DFC_2_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, MIPI_DCS_SET_COLUMN_ADDRESS,
> > > + ili->conf->column_addr,
> > > + ILI9341_COLUMN_ADDR_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, MIPI_DCS_SET_PAGE_ADDRESS,
> > > + ili->conf->page_addr,
> > > + ILI9341_PAGE_ADDR_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_INTERFACE,
> > > + ili->conf->interface,
> > > + ILI9341_INTERFACE_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, MIPI_DCS_SET_PIXEL_FORMAT,
> > > + &ili->conf->pixel_format,
> > > + 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + msleep(200);
> > > + ret = _ili9341_command(ili, MIPI_DCS_SET_GAMMA_CURVE,
> > > + &ili->conf->gamma_curve,
> > > + 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_PGAMMA,
> > > + ili->conf->pgamma,
> > > + ILI9341_PGAMMA_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = _ili9341_command(ili, ILI9341_NGAMMA,
> > > + ili->conf->ngamma,
> > > + ILI9341_NGAMMA_LEN);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = ili9341_command(ili, MIPI_DCS_EXIT_SLEEP_MODE);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + msleep(200);
> > > + ret = ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + dev_info(ili->dev, "initialized display rgb interface\n");
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int ili9341_dpi_power_on(struct ili9341 *ili)
> > > +{
> > > + int ret = 0;
> > > +
> > > + /* Assert RESET */
> > > + gpiod_set_value(ili->reset_gpio, 1);
> > > +
> > > + /* Enable power */
> > > + if (!IS_ERR(ili->vcc)) {
> > > + ret = regulator_enable(ili->vcc);
> > > + if (ret < 0) {
> > > + dev_err(ili->dev, "unable to enable vcc\n");
> > > + return ret;
> > > + }
> > > + }
> > > + msleep(20);
> > > +
> > > + /* De-assert RESET */
> > > + gpiod_set_value(ili->reset_gpio, 0);
> > > + msleep(10);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int ili9341_dpi_power_off(struct ili9341 *ili)
> > > +{
> > > + /* Assert RESET */
> > > + gpiod_set_value(ili->reset_gpio, 1);
> > > +
> > > + /* Disable power */
> > > + if (!IS_ERR(ili->vcc))
> > > + return regulator_disable(ili->vcc);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int ili9341_dpi_disable(struct drm_panel *panel)
> > > +{
> > > + struct ili9341 *ili = panel_to_ili9341(panel);
> > > +
> > > + ili9341_command(ili, MIPI_DCS_SET_DISPLAY_OFF);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int ili9341_dpi_unprepare(struct drm_panel *panel)
> > > +{
> > > + struct ili9341 *ili = panel_to_ili9341(panel);
> > > +
> > > + return ili9341_dpi_power_off(ili);
> > > +}
> > > +
> > > +static int ili9341_dpi_prepare(struct drm_panel *panel)
> > > +{
> > > + struct ili9341 *ili = panel_to_ili9341(panel);
> > > + int ret;
> > > +
> > > + ret = ili9341_dpi_power_on(ili);
> > > + if (ret < 0)
> > > + return ret;
> > > +
> > > + ret = ili9341_dpi_init(ili);
> > > + if (ret < 0)
> > > + ili9341_dpi_unprepare(panel);
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +static int ili9341_dpi_enable(struct drm_panel *panel)
> > > +{
> > > + struct ili9341 *ili = panel_to_ili9341(panel);
> > > +
> > > + ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int ili9341_dpi_get_modes(struct drm_panel *panel,
> > > + struct drm_connector *connector)
> > > +{
> > > + struct ili9341 *ili = panel_to_ili9341(panel);
> > > + struct drm_device *drm = connector->dev;
> > > + struct drm_display_mode *mode;
> > > + struct drm_display_info *info;
> > > +
> > > + info = &connector->display_info;
> > > + info->width_mm = ili->conf->mode.width_mm;
> > > + info->height_mm = ili->conf->mode.height_mm;
> > > +
> > > + if (ili->conf->rgb_interface & ILI9341_RGB_DPL)
> > > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE;
> > > + else
> > > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE;
> > > +
> > > + if (ili->conf->rgb_interface & ILI9341_RGB_EPL)
> > > + info->bus_flags |= DRM_BUS_FLAG_DE_LOW;
> > > + else
> > > + info->bus_flags |= DRM_BUS_FLAG_DE_HIGH;
> > > +
> > > + mode = drm_mode_duplicate(drm, &ili->conf->mode);
> > > + if (!mode) {
> > > + DRM_ERROR("bad mode or failed to add mode\n");
> > > + return -EINVAL;
> > > + }
> > > + drm_mode_set_name(mode);
> > > +
> > > + /* Set up the polarity */
> > > + if (ili->conf->rgb_interface & ILI9341_RGB_HSPL)
> > > + mode->flags |= DRM_MODE_FLAG_PHSYNC;
> > > + else
> > > + mode->flags |= DRM_MODE_FLAG_NHSYNC;
> > > +
> > > + if (ili->conf->rgb_interface & ILI9341_RGB_VSPL)
> > > + mode->flags |= DRM_MODE_FLAG_PVSYNC;
> > > + else
> > > + mode->flags |= DRM_MODE_FLAG_NVSYNC;
> > > +
> > > + drm_mode_probed_add(connector, mode);
> > > +
> > > + return 1; /* Number of modes */
> > > +}
> > > +
> > > +static const struct drm_panel_funcs ili9341_dpi_funcs = {
> > > + .disable = ili9341_dpi_disable,
> > > + .unprepare = ili9341_dpi_unprepare,
> > > + .prepare = ili9341_dpi_prepare,
> > > + .enable = ili9341_dpi_enable,
> > > + .get_modes = ili9341_dpi_get_modes,
> > > +};
> > > +
> > > +static int ili9341_dpi_probe(struct spi_device *spi)
> > > +{
> > > + int ret;
> > > + struct device *dev = &spi->dev;
> > > + struct ili9341 *ili;
> > > +
> > > + ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL);
> > > + if (!ili)
> > > + return -ENOMEM;
> > > +
> > > + spi_set_drvdata(spi, ili);
> > > +
> > > + ili->dev = dev;
> > > + /*
> > > + * Every new incarnation of this display must have a unique
> > > + * data entry for the system in this driver.
> > > + */
> > > + ili->conf = of_device_get_match_data(dev);
> > > + if (!ili->conf) {
> > > + dev_err(dev, "missing device configuration\n");
> > > + return -ENODEV;
> > > + }
> > > +
> > > + ili->vcc = devm_regulator_get_optional(dev, "vcc");
> > > + if (IS_ERR(ili->vcc))
> > > + dev_err(dev, "get optional vcc failed\n");
> > > +
> > > + ili->reset_gpio = devm_gpiod_get_optional(dev, "reset",
> > > + GPIOD_OUT_HIGH);
> > > + if (IS_ERR(ili->reset_gpio)) {
> > > + dev_err(dev, "failed to get RESET GPIO\n");
> > > + return PTR_ERR(ili->reset_gpio);
> > > + }
> > > +
> > > + ili->dc_gpio = devm_gpiod_get(dev, "dc", GPIOD_OUT_LOW);
> > > + if (IS_ERR(ili->dc_gpio)) {
> > > + dev_err(dev, "failed to get DC GPIO\n");
> > > + return PTR_ERR(ili->dc_gpio);
> > > + }
> > > +
> > > + spi->bits_per_word = 8;
> > > + ret = spi_setup(spi);
> > > + if (ret < 0) {
> > > + dev_err(dev, "spi setup failed.\n");
> > > + return ret;
> > > + }
> > > +
> > > + ili->max_spi_speed = ili->conf->max_spi_speed;
> > > +
> > > + drm_panel_init(&ili->panel, dev, &ili9341_dpi_funcs,
> > > + DRM_MODE_CONNECTOR_DPI);
> > > +
> > > + drm_panel_add(&ili->panel);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +
> > > +
> > > +static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe,
> > > + struct drm_crtc_state *crtc_state,
> > > + struct drm_plane_state *plane_state)
> > > +{
> > > + struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev);
> > > + struct mipi_dbi *dbi = &dbidev->dbi;
> > > + u8 addr_mode;
> > > + int ret, idx;
> > > +
> > > + if (!drm_dev_enter(pipe->crtc.dev, &idx))
> > > + return;
> > > +
> > > + DRM_DEBUG_KMS("\n");
> > > +
> > > + ret = mipi_dbi_poweron_conditional_reset(dbidev);
> > > + if (ret < 0)
> > > + goto out_exit;
> > > + if (ret == 1)
> > > + goto out_enable;
> > > +
> > > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF);
> > > +
> > > + mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30);
> > > + mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81);
> > > + mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78);
> > > + mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02);
> > > + mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL);
> > > + mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00);
> > > +
> > > + /* Power Control */
> > > + mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V);
> > > + mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT);
> > > + /* VCOM */
> > > + mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V,
> > > + ILI9341_DBI_VCOM_1_VML_1P5V);
> > > + mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58);
> > > +
> > > + /* Memory Access Control */
> > > + mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT,
> > > + MIPI_DCS_PIXEL_FMT_16BIT);
> > > +
> > > + /* Frame Rate */
> > > + mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03,
> > > + ILI9341_DBI_FRC_RTNA & 0x1f);
> > > +
> > > + /* Gamma */
> > > + mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00);
> > > + mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1);
> > > + mipi_dbi_command(dbi, ILI9341_PGAMMA,
> > > + 0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1,
> > > + 0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00);
> > > + mipi_dbi_command(dbi, ILI9341_NGAMMA,
> > > + 0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1,
> > > + 0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f);
> > > +
> > > + /* DDRAM */
> > > + mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS |
> > > + ILI9341_DBI_EMS_DTS |
> > > + ILI9341_DBI_EMS_GON);
> > > +
> > > + /* Display */
> > > + mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00);
> > > + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
> > > + msleep(100);
> > > +
> > > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
> > > + msleep(100);
> > > +
> > > +out_enable:
> > > + switch (dbidev->rotation) {
> > > + default:
> > > + addr_mode = ILI9341_MADCTL_MX;
> > > + break;
> > > + case 90:
> > > + addr_mode = ILI9341_MADCTL_MV;
> > > + break;
> > > + case 180:
> > > + addr_mode = ILI9341_MADCTL_MY;
> > > + break;
> > > + case 270:
> > > + addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY |
> > > + ILI9341_MADCTL_MX;
> > > + break;
> > > + }
> > > + addr_mode |= ILI9341_MADCTL_BGR;
> > > + mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode);
> > > + mipi_dbi_enable_flush(dbidev, crtc_state, plane_state);
> > > + DRM_DEBUG_KMS("initialized display serial interface\n");
> > > +out_exit:
> > > + drm_dev_exit(idx);
> > > +}
> > > +
> > > +static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = {
> > > + .enable = ili9341_dbi_enable,
> > > + .disable = mipi_dbi_pipe_disable,
> > > + .update = mipi_dbi_pipe_update,
> > > + .prepare_fb = drm_gem_simple_display_pipe_prepare_fb,
> > > +};
> > > +
> > > +static const struct drm_display_mode ili9341_dbi_mode = {
> > > + DRM_SIMPLE_MODE(240, 320, 37, 49),
> > > +};
> > > +
> > > +DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops);
> > > +
> > > +static struct drm_driver ili9341_dbi_driver = {
> > > + .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC,
> > > + .fops = &ili9341_dbi_fops,
> > > + DRM_GEM_CMA_DRIVER_OPS_VMAP,
> > > + .debugfs_init = mipi_dbi_debugfs_init,
> > > + .name = "ili9341",
> > > + .desc = "Ilitek ILI9341",
> > > + .date = "20180514",
> > > + .major = 1,
> > > + .minor = 0,
> > > +};
> > > +static int ili9341_dbi_probe(struct spi_device *spi)
> > > +{
> > > + struct mipi_dbi_dev *dbidev;
> > > + struct drm_device *drm;
> > > + struct mipi_dbi *dbi;
> > > + struct gpio_desc *dc;
> > > + struct device *dev = &spi->dev;
> > > + u32 rotation = 0;
> > > + int ret;
> > > +
> > > + dbidev = devm_drm_dev_alloc(dev, &ili9341_dbi_driver,
> > > + struct mipi_dbi_dev, drm);
> > > + if (IS_ERR(dbidev))
> > > + return PTR_ERR(dbidev);
> > > +
> > > + dbi = &dbidev->dbi;
> > > + drm = &dbidev->drm;
> > > +
> > > + drm_mode_config_init(drm);
> > > +
> > > + dbi->reset = devm_gpiod_get_optional(dev, "reset",
> > > + GPIOD_OUT_HIGH);
> > > + if (IS_ERR(dbi->reset)) {
> > > + DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n");
> > > + return PTR_ERR(dbi->reset);
> > > + }
> > > +
> > > + dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW);
> > > + if (IS_ERR(dc)) {
> > > + DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n");
> > > + return PTR_ERR(dc);
> > > + }
> > > +
> > > + dbidev->regulator = devm_regulator_get_optional(dev, "vcc");
> > > + if (IS_ERR(dbidev->regulator))
> > > + dev_err(dev, "get optional vcc failed\n");
> > > +
> > > + dbidev->backlight = devm_of_find_backlight(dev);
> > > + if (IS_ERR(dbidev->backlight))
> > > + return PTR_ERR(dbidev->backlight);
> > > +
> > > + device_property_read_u32(dev, "rotation", &rotation);
> > > +
> > > + ret = mipi_dbi_spi_init(spi, dbi, dc);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = mipi_dbi_dev_init(dbidev, &ili9341_dbi_funcs,
> > > + &ili9341_dbi_mode, rotation);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + drm_mode_config_reset(drm);
> > > +
> > > + ret = drm_dev_register(drm, 0);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + spi_set_drvdata(spi, drm);
> > > +
> > > + drm_fbdev_generic_setup(drm, 0);
> > > +
> > > + return 0;
> > > +}
> > > +static int ili9341_probe(struct spi_device *spi)
> > > +{
> > > + const struct spi_device_id *id = spi_get_device_id(spi);
> > > +
> > > + if (!strcmp(id->name, "sf-tc240t-9370-t"))
> > > + return ili9341_dpi_probe(spi);
> > > + else if (!strcmp(id->name, "yx240qv29"))
> > > + return ili9341_dbi_probe(spi);
> > > +
> > > + return -1;
> > > +}
> > > +
> > > +static int ili9341_remove(struct spi_device *spi)
> > > +{
> > > + const struct spi_device_id *id = spi_get_device_id(spi);
> > > + struct ili9341 *ili = spi_get_drvdata(spi);
> > > + struct drm_device *drm = spi_get_drvdata(spi);
> > > +
> > > + if (!strcmp(id->name, "sf-tc240t-9370-t")) {
> > > + ili9341_dpi_power_off(ili);
> > > + drm_panel_remove(&ili->panel);
> > > + } else if (!strcmp(id->name, "yx240qv29")) {
> > > + drm_dev_unplug(drm);
> > > + drm_atomic_helper_shutdown(drm);
> > > + }
> > > + return 0;
> > > +}
> > > +
> > > +static void ili9341_shutdown(struct spi_device *spi)
> > > +{
> > > + const struct spi_device_id *id = spi_get_device_id(spi);
> > > +
> > > + if (!strcmp(id->name, "yx240qv29"))
> > > + drm_atomic_helper_shutdown(spi_get_drvdata(spi));
> > > +}
> > > +
> > > +static const struct of_device_id ili9341_of_match[] = {
> > > + {
> > > + .compatible = "st,sf-tc240t-9370-t",
> > > + .data = &ili9341_stm32f429_disco_data,
> > > + },
> > > + {
> > > + /* porting from tiny/ili9341.c
> > > + * for original mipi dbi compitable
> > > + */
> > > + .compatible = "adafruit,yx240qv29",
> > > + .data = NULL,
> > > + },
> > > +};
> > > +MODULE_DEVICE_TABLE(of, ili9341_of_match);
> > > +
> > > +static const struct spi_device_id ili9341_id[] = {
> > > + { "yx240qv29", 0 },
> > > + { "sf-tc240t-9370-t", 0 },
> > > + { }
> > > +};
> > > +MODULE_DEVICE_TABLE(spi, ili9341_id);
> > > +
> > > +static struct spi_driver ili9341_driver = {
> > > + .probe = ili9341_probe,
> > > + .remove = ili9341_remove,
> > > + .shutdown = ili9341_shutdown,
> > > + .id_table = ili9341_id,
> > > + .driver = {
> > > + .name = "panel-ilitek-ili9341",
> > > + .of_match_table = ili9341_of_match,
> > > + },
> > > +};
> > > +module_spi_driver(ili9341_driver);
> > > +
> > > +MODULE_AUTHOR("Dillon Min <dillon.minfei@xxxxxxxxx>");
> > > +MODULE_DESCRIPTION("ILI9341 LCD panel driver");
> > > +MODULE_LICENSE("GPL v2");
> > >

Next message: Dmitry Osipenko: "[PATCH v6 01/14] regulator: core: Add regulator_sync_voltage_rdev()"
Previous message: Florian Fainelli: "Re: [PATCH 5.10 000/252] 5.10.42-rc1 review"
In reply to: Dillon Min: "Re: [PATCH 1/4] drm/panel: Add ilitek ili9341 panel driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]