[PATCH V2] remoteproc: imx_rproc: correct firmware reload
From: Peng Fan (OSS)
Date: Wed Jun 02 2021 - 02:09:16 EST
From: Peng Fan <peng.fan@xxxxxxx>
ENABLE_M4 should be set to 1 when loading code to TCM, otherwise
you will not able to replace the firmware after you stop m4.
Besides ENABLE_M4, we still need set SW_M4C_RST, because this bit
will be automatically set with SW_M4C_NON_SCLR_RST set.
Reviewed-by: Mathieu Poirier <mathieu.poirier@xxxxxxxxxx>
Signed-off-by: Peng Fan <peng.fan@xxxxxxx>
---
V2:
Add R-b tag from Mathieu
Rebase on remoteproc/for-next
This https://patchwork.kernel.org/project/linux-remoteproc/cover/1620274123-1461-1-git-send-email-peng.fan@xxxxxxxxxxx/
has been merged in remoteproc/for-next, so not mark here as dependency.
drivers/remoteproc/imx_rproc.c | 8 +++++---
1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/drivers/remoteproc/imx_rproc.c b/drivers/remoteproc/imx_rproc.c
index 7cc0cadea1cc..ce2ce42bee91 100644
--- a/drivers/remoteproc/imx_rproc.c
+++ b/drivers/remoteproc/imx_rproc.c
@@ -33,7 +33,8 @@
#define IMX7D_M4_START (IMX7D_ENABLE_M4 | IMX7D_SW_M4P_RST \
| IMX7D_SW_M4C_RST)
-#define IMX7D_M4_STOP IMX7D_SW_M4C_NON_SCLR_RST
+#define IMX7D_M4_STOP (IMX7D_ENABLE_M4 | IMX7D_SW_M4C_RST | \
+ IMX7D_SW_M4C_NON_SCLR_RST)
/* Address: 0x020D8000 */
#define IMX6SX_SRC_SCR 0x00
@@ -44,7 +45,8 @@
#define IMX6SX_M4_START (IMX6SX_ENABLE_M4 | IMX6SX_SW_M4P_RST \
| IMX6SX_SW_M4C_RST)
-#define IMX6SX_M4_STOP IMX6SX_SW_M4C_NON_SCLR_RST
+#define IMX6SX_M4_STOP (IMX6SX_ENABLE_M4 | IMX6SX_SW_M4C_RST | \
+ IMX6SX_SW_M4C_NON_SCLR_RST)
#define IMX6SX_M4_RST_MASK (IMX6SX_ENABLE_M4 | IMX6SX_SW_M4P_RST \
| IMX6SX_SW_M4C_NON_SCLR_RST \
| IMX6SX_SW_M4C_RST)
@@ -691,7 +693,7 @@ static int imx_rproc_detect_mode(struct imx_rproc *priv)
return ret;
}
- if (!(val & dcfg->src_stop))
+ if ((val & dcfg->src_mask) != dcfg->src_stop)
priv->rproc->state = RPROC_DETACHED;
return 0;
--
2.30.0