Re: [RFC PATCH v3 11/12] firmware: arm_scmi: Add virtio transport

[Vincent Guittot]

On Wed, 2 Jun 2021 at 10:25, Peter Hilber <peter.hilber@xxxxxxxxxxxxxxx> wrote:
>
> On 01.06.21 16:53, Vincent Guittot wrote:
> > On Tue, 11 May 2021 at 02:28, Peter Hilber <peter.hilber@xxxxxxxxxxxxxxx> wrote:
> >>
> >> From: Igor Skalkin <igor.skalkin@xxxxxxxxxxxxxxx>
> >>
> >> This transport enables accessing an SCMI platform as a virtio device.
> >>
> >> Implement an SCMI virtio driver according to the virtio SCMI device spec
> >> [1]. Virtio device id 32 has been reserved for the SCMI device [2].
> >>
> >> The virtio transport has one Tx channel (virtio cmdq, A2P channel) and
> >> at most one Rx channel (virtio eventq, P2A channel).
> >>
> >> The following feature bit defined in [1] is not implemented:
> >> VIRTIO_SCMI_F_SHARED_MEMORY.
> >>
> >> After the preparatory patches, this implements the virtio transport as
> >> paraphrased:
> >>
> >> Only support a single arm-scmi device (which is consistent with the SCMI
> >> spec). scmi-virtio init is called from arm-scmi module init. During the
> >> arm-scmi probing, link to the first probed scmi-virtio device. Defer
> >> arm-scmi probing if no scmi-virtio device is bound yet.
> >>
> >> For simplicity, restrict the number of messages which can be pending
> >> simultaneously according to the virtqueue capacity. (The virtqueue sizes
> >> are negotiated with the virtio device.)
> >>
> >> As soon as Rx channel message buffers are allocated or have been read
> >> out by the arm-scmi driver, feed them to the virtio device.
> >>
> >> Since some virtio devices may not have the short response time exhibited
> >> by SCMI platforms using other transports, set a generous response
> >> timeout.
> >>
> >> Limitations:
> >>
> >> - Polling is not supported.
> >>
> >> - The timeout for delayed responses has not been adjusted.
> >>
> >> [1] https://github.com/oasis-tcs/virtio-spec/blob/master/virtio-scmi.tex
> >> [2] https://www.oasis-open.org/committees/ballot.php?id=3496
> >>
> >> Signed-off-by: Igor Skalkin <igor.skalkin@xxxxxxxxxxxxxxx>
> >> [ Peter: Adapted patch for submission to upstream. ]
> >> Co-developed-by: Peter Hilber <peter.hilber@xxxxxxxxxxxxxxx>
> >> Signed-off-by: Peter Hilber <peter.hilber@xxxxxxxxxxxxxxx>
> >> ---
> >>  MAINTAINERS                        |   1 +
> >>  drivers/firmware/Kconfig           |  12 +
> >>  drivers/firmware/arm_scmi/Makefile |   1 +
> >>  drivers/firmware/arm_scmi/common.h |   3 +
> >>  drivers/firmware/arm_scmi/driver.c |   3 +
> >>  drivers/firmware/arm_scmi/virtio.c | 523 +++++++++++++++++++++++++++++
> >>  include/uapi/linux/virtio_ids.h    |   1 +
> >>  include/uapi/linux/virtio_scmi.h   |  25 ++
> >>  8 files changed, 569 insertions(+)
> >>  create mode 100644 drivers/firmware/arm_scmi/virtio.c
> >>  create mode 100644 include/uapi/linux/virtio_scmi.h
> >>
> >> diff --git a/MAINTAINERS b/MAINTAINERS
> >> index bd7aff0c120f..449c336872f3 100644
> >> --- a/MAINTAINERS
> >> +++ b/MAINTAINERS
> >> @@ -17705,6 +17705,7 @@ F:      drivers/regulator/scmi-regulator.c
> >>  F:     drivers/reset/reset-scmi.c
> >>  F:     include/linux/sc[mp]i_protocol.h
> >>  F:     include/trace/events/scmi.h
> >> +F:     include/uapi/linux/virtio_scmi.h
> >>
> >>  SYSTEM RESET/SHUTDOWN DRIVERS
> >>  M:     Sebastian Reichel <sre@xxxxxxxxxx>
> >> diff --git a/drivers/firmware/Kconfig b/drivers/firmware/Kconfig
> >> index e8377b12e4d0..7e9eafdd9b63 100644
> >> --- a/drivers/firmware/Kconfig
> >> +++ b/drivers/firmware/Kconfig
> >> @@ -39,6 +39,18 @@ config ARM_SCMI_HAVE_MSG
> >>           This declares whether a message passing based transport for SCMI is
> >>           available.
> >>
> >> +# This config option includes the dependencies of ARM_SCMI_PROTOCOL so that
> >> +# this config doesn't show up when SCMI wouldn't be available.
> >> +config VIRTIO_SCMI
> >> +       bool "Virtio transport for SCMI"
> >> +       select ARM_SCMI_HAVE_MSG
> >> +       depends on VIRTIO && (ARM || ARM64 || COMPILE_TEST)
> >> +       help
> >> +         This enables the virtio based transport for SCMI.
> >> +
> >> +         If you want to use the ARM SCMI protocol between the virtio guest and
> >> +         a host providing a virtio SCMI device, answer Y.
> >> +
> >>  config ARM_SCMI_POWER_DOMAIN
> >>         tristate "SCMI power domain driver"
> >>         depends on ARM_SCMI_PROTOCOL || (COMPILE_TEST && OF)
> >> diff --git a/drivers/firmware/arm_scmi/Makefile b/drivers/firmware/arm_scmi/Makefile
> >> index f6b4acb8abdb..db1787606fb2 100644
> >> --- a/drivers/firmware/arm_scmi/Makefile
> >> +++ b/drivers/firmware/arm_scmi/Makefile
> >> @@ -5,6 +5,7 @@ scmi-transport-$(CONFIG_ARM_SCMI_HAVE_SHMEM) = shmem.o
> >>  scmi-transport-$(CONFIG_MAILBOX) += mailbox.o
> >>  scmi-transport-$(CONFIG_HAVE_ARM_SMCCC_DISCOVERY) += smc.o
> >>  scmi-transport-$(CONFIG_ARM_SCMI_HAVE_MSG) += msg.o
> >> +scmi-transport-$(CONFIG_VIRTIO_SCMI) += virtio.o
> >>  scmi-protocols-y = base.o clock.o perf.o power.o reset.o sensors.o system.o voltage.o
> >>  scmi-module-objs := $(scmi-bus-y) $(scmi-driver-y) $(scmi-protocols-y) \
> >>                     $(scmi-transport-y)
> >> diff --git a/drivers/firmware/arm_scmi/common.h b/drivers/firmware/arm_scmi/common.h
> >> index 4cb6571c7aaf..bada06cfd33d 100644
> >> --- a/drivers/firmware/arm_scmi/common.h
> >> +++ b/drivers/firmware/arm_scmi/common.h
> >> @@ -349,6 +349,9 @@ extern const struct scmi_desc scmi_mailbox_desc;
> >>  #ifdef CONFIG_HAVE_ARM_SMCCC
> >>  extern const struct scmi_desc scmi_smc_desc;
> >>  #endif
> >> +#ifdef CONFIG_VIRTIO_SCMI
> >> +extern const struct scmi_desc scmi_virtio_desc;
> >> +#endif
> >>
> >>  int scmi_set_transport_info(struct device *dev, void *transport_info);
> >>  void *scmi_get_transport_info(struct device *dev);
> >> diff --git a/drivers/firmware/arm_scmi/driver.c b/drivers/firmware/arm_scmi/driver.c
> >> index e04e7c8e6928..a31187385470 100644
> >> --- a/drivers/firmware/arm_scmi/driver.c
> >> +++ b/drivers/firmware/arm_scmi/driver.c
> >> @@ -1637,6 +1637,9 @@ static const struct of_device_id scmi_of_match[] = {
> >>  #endif
> >>  #ifdef CONFIG_HAVE_ARM_SMCCC_DISCOVERY
> >>         { .compatible = "arm,scmi-smc", .data = &scmi_smc_desc},
> >> +#endif
> >> +#ifdef CONFIG_VIRTIO_SCMI
> >> +       { .compatible = "arm,scmi-virtio", .data = &scmi_virtio_desc},
> >>  #endif
> >>         { /* Sentinel */ },
> >>  };
> >> diff --git a/drivers/firmware/arm_scmi/virtio.c b/drivers/firmware/arm_scmi/virtio.c
> >> new file mode 100644
> >> index 000000000000..20972adf6dc7
> >> --- /dev/null
> >> +++ b/drivers/firmware/arm_scmi/virtio.c
> >> @@ -0,0 +1,523 @@
> >> +// SPDX-License-Identifier: GPL-2.0
> >> +/*
> >> + * Virtio Transport driver for Arm System Control and Management Interface
> >> + * (SCMI).
> >> + *
> >> + * Copyright (C) 2020 OpenSynergy.
> >> + */
> >> +
> >> +/**
> >> + * DOC: Theory of Operation
> >> + *
> >> + * The scmi-virtio transport implements a driver for the virtio SCMI device.
> >> + *
> >> + * There is one Tx channel (virtio cmdq, A2P channel) and at most one Rx
> >> + * channel (virtio eventq, P2A channel). Each channel is implemented through a
> >> + * virtqueue. Access to each virtqueue is protected by spinlocks.
> >> + */
> >> +
> >> +#include <linux/errno.h>
> >> +#include <linux/of.h>
> >> +#include <linux/of_platform.h>
> >> +#include <linux/platform_device.h>
> >> +#include <linux/module.h>
> >> +#include <linux/slab.h>
> >> +#include <linux/virtio.h>
> >> +#include <linux/virtio_config.h>
> >> +#include <uapi/linux/virtio_ids.h>
> >> +#include <uapi/linux/virtio_scmi.h>
> >> +
> >> +#include "common.h"
> >> +
> >> +#define VIRTIO_SCMI_MAX_MSG_SIZE 128 /* Value may be increased. */
> >> +#define VIRTIO_SCMI_MAX_PDU_SIZE \
> >> +       (VIRTIO_SCMI_MAX_MSG_SIZE + SCMI_MSG_MAX_PROT_OVERHEAD)
> >> +#define DESCRIPTORS_PER_TX_MSG 2
> >> +
> >> +/**
> >> + * struct scmi_vio_channel - Transport channel information
> >> + *
> >> + * @lock: Protects access to all members except ready.
> >> + * @ready_lock: Protects access to ready. If required, it must be taken before
> >> + *              lock.
> >> + * @vqueue: Associated virtqueue
> >> + * @cinfo: SCMI Tx or Rx channel
> >> + * @free_list: List of unused scmi_vio_msg, maintained for Tx channels only
> >> + * @is_rx: Whether channel is an Rx channel
> >> + * @ready: Whether transport user is ready to hear about channel
> >> + */
> >> +struct scmi_vio_channel {
> >> +       spinlock_t lock;
> >> +       spinlock_t ready_lock;
> >> +       struct virtqueue *vqueue;
> >> +       struct scmi_chan_info *cinfo;
> >> +       struct list_head free_list;
> >> +       u8 is_rx;
> >> +       u8 ready;
> >> +};
> >> +
> >> +/**
> >> + * struct scmi_vio_msg - Transport PDU information
> >> + *
> >> + * @request: SDU used for commands
> >> + * @input: SDU used for (delayed) responses and notifications
> >> + * @list: List which scmi_vio_msg may be part of
> >> + * @rx_len: Input SDU size in bytes, once input has been received
> >> + */
> >> +struct scmi_vio_msg {
> >> +       struct scmi_msg_payld *request;
> >> +       struct scmi_msg_payld *input;
> >> +       struct list_head list;
> >> +       unsigned int rx_len;
> >> +};
> >> +
> >> +static bool scmi_vio_have_vq_rx(struct virtio_device *vdev)
> >> +{
> >> +       return virtio_has_feature(vdev, VIRTIO_SCMI_F_P2A_CHANNELS);
> >> +}
> >> +
> >> +static int scmi_vio_feed_vq_rx(struct scmi_vio_channel *vioch,
> >> +                              struct scmi_vio_msg *msg)
> >> +{
> >> +       struct scatterlist sg_in;
> >> +       int rc;
> >> +       unsigned long flags;
> >> +
> >> +       sg_init_one(&sg_in, msg->input, VIRTIO_SCMI_MAX_PDU_SIZE);
> >> +
> >> +       spin_lock_irqsave(&vioch->lock, flags);
> >> +
> >> +       rc = virtqueue_add_inbuf(vioch->vqueue, &sg_in, 1, msg, GFP_ATOMIC);
> >> +       if (rc)
> >> +               dev_err_once(vioch->cinfo->dev,
> >> +                            "%s() failed to add to virtqueue (%d)\n", __func__,
> >> +                            rc);
> >> +       else
> >> +               virtqueue_kick(vioch->vqueue);
> >> +
> >> +       spin_unlock_irqrestore(&vioch->lock, flags);
> >> +
> >> +       return rc;
> >> +}
> >> +
> >> +static void scmi_vio_complete_cb(struct virtqueue *vqueue)
> >> +{
> >> +       unsigned long ready_flags;
> >> +       unsigned long flags;
> >> +       unsigned int length;
> >> +       struct scmi_vio_channel *vioch;
> >> +       struct scmi_vio_msg *msg;
> >> +       bool cb_enabled = true;
> >> +
> >> +       if (WARN_ON_ONCE(!vqueue->vdev->priv))
> >> +               return;
> >> +       vioch = &((struct scmi_vio_channel *)vqueue->vdev->priv)[vqueue->index];
> >> +
> >> +       for (;;) {
> >> +               spin_lock_irqsave(&vioch->ready_lock, ready_flags);
> >> +
> >> +               if (!vioch->ready) {
> >> +                       if (!cb_enabled)
> >> +                               (void)virtqueue_enable_cb(vqueue);
> >> +                       goto unlock_ready_out;
> >> +               }
> >> +
> >> +               spin_lock_irqsave(&vioch->lock, flags);
> >> +               if (cb_enabled) {
> >> +                       virtqueue_disable_cb(vqueue);
> >> +                       cb_enabled = false;
> >> +               }
> >> +               msg = virtqueue_get_buf(vqueue, &length);
> >> +               if (!msg) {
> >> +                       if (virtqueue_enable_cb(vqueue))
> >> +                               goto unlock_out;
> >> +                       else
> >> +                               cb_enabled = true;
> >> +               }
> >> +               spin_unlock_irqrestore(&vioch->lock, flags);
> >> +
> >> +               if (msg) {
> >> +                       msg->rx_len = length;
> >> +
> >> +                       /*
> >> +                        * Hold the ready_lock during the callback to avoid
> >> +                        * races when the arm-scmi driver is unbinding while
> >> +                        * the virtio device is not quiesced yet.
> >> +                        */
> >> +                       scmi_rx_callback(vioch->cinfo,
> >> +                                        msg_read_header(msg->input), msg);
> >> +               }
> >> +               spin_unlock_irqrestore(&vioch->ready_lock, ready_flags);
> >> +       }
> >> +
> >> +unlock_out:
> >> +       spin_unlock_irqrestore(&vioch->lock, flags);
> >> +unlock_ready_out:
> >> +       spin_unlock_irqrestore(&vioch->ready_lock, ready_flags);
> >> +}
> >> +
> >> +static const char *const scmi_vio_vqueue_names[] = { "tx", "rx" };
> >> +
> >> +static vq_callback_t *scmi_vio_complete_callbacks[] = {
> >> +       scmi_vio_complete_cb,
> >> +       scmi_vio_complete_cb
> >> +};
> >> +
> >> +static unsigned int virtio_get_max_msg(bool tx,
> >> +                                      struct scmi_chan_info *base_cinfo)
> >> +{
> >> +       struct scmi_vio_channel *vioch = base_cinfo->transport_info;
> >> +       unsigned int ret;
> >> +
> >> +       ret = virtqueue_get_vring_size(vioch->vqueue);
> >> +
> >> +       /* Tx messages need multiple descriptors. */()
> >> +       if (tx)
> >> +               ret /= DESCRIPTORS_PER_TX_MSG;
> >> +
> >> +       if (ret > MSG_TOKEN_MAX) {
> >
> > __scmi_xfer_info_init() returns error for info->max_msg >=
> > MSG_TOKEN_MAX so it should be (ret >= MSG_TOKEN_MAX
> >
>
> I think it would be better to use the > comparison in
> __scmi_xfer_info_init(), too. That should work in my understanding. I

yes should work as well

> think that change was originally in my branch, but I lost it somehow.
>
> >
> >> +               dev_info_once(
> >> +                       base_cinfo->dev,
> >> +                       "Only %ld messages can be pending simultaneously, while the %s virtqueue could hold %d\n",
> >> +                       MSG_TOKEN_MAX, tx ? "tx" : "rx", ret);
> >> +               ret = MSG_TOKEN_MAX;
> >
> > should be ret = MSG_TOKEN_MAX-1;
> >
> >> +       }
> >> +
> >> +       return ret;
> >> +}
> >> +
> >> +static int scmi_vio_match_any_dev(struct device *dev, const void *data)
> >> +{
> >> +       return 1;
> >> +}
> >> +
> >> +static struct virtio_driver virtio_scmi_driver; /* Forward declaration */
> >> +
> >> +static int virtio_link_supplier(struct device *dev)
> >> +{
> >> +       struct device *vdev = driver_find_device(
> >> +               &virtio_scmi_driver.driver, NULL, NULL, scmi_vio_match_any_dev);
> >> +
> >> +       if (!vdev) {
> >> +               dev_notice_once(
> >> +                       dev,
> >> +                       "Deferring probe after not finding a bound scmi-virtio device\n");
> >> +               return -EPROBE_DEFER;
> >> +       }
> >> +
> >> +       /* Add device link for remove order and sysfs link. */
> >> +       if (!device_link_add(dev, vdev, DL_FLAG_AUTOREMOVE_CONSUMER)) {
> >> +               put_device(vdev);
> >> +               dev_err(dev, "Adding link to supplier virtio device failed\n");
> >> +               return -ECANCELED;
> >> +       }
> >> +
> >> +       put_device(vdev);
> >> +       return scmi_set_transport_info(dev, dev_to_virtio(vdev));
> >> +}
> >> +
> >> +static bool virtio_chan_available(struct device *dev, int idx)
> >> +{
> >> +       struct virtio_device *vdev;
> >> +
> >> +       /* scmi-virtio doesn't support per-protocol channels */
> >> +       if (is_scmi_protocol_device(dev))
> >> +               return false;
> >> +
> >> +       vdev = scmi_get_transport_info(dev);
> >> +       if (!vdev)
> >> +               return false;
> >> +
> >> +       switch (idx) {
> >> +       case VIRTIO_SCMI_VQ_TX:
> >> +               return true;
> >> +       case VIRTIO_SCMI_VQ_RX:
> >> +               return scmi_vio_have_vq_rx(vdev);
> >> +       default:
> >> +               return false;
> >> +       }
> >> +}
> >> +
> >> +static int virtio_chan_setup(struct scmi_chan_info *cinfo, struct device *dev,
> >> +                            bool tx)
> >> +{
> >> +       unsigned long flags;
> >> +       struct virtio_device *vdev;
> >> +       struct scmi_vio_channel *vioch;
> >> +       int index = tx ? VIRTIO_SCMI_VQ_TX : VIRTIO_SCMI_VQ_RX;
> >> +       int max_msg;
> >> +       int i;
> >> +
> >> +       if (!virtio_chan_available(dev, index))
> >> +               return -ENODEV;
> >> +
> >> +       vdev = scmi_get_transport_info(dev);
> >> +       vioch = &((struct scmi_vio_channel *)vdev->priv)[index];
> >> +
> >> +       spin_lock_irqsave(&vioch->lock, flags);
> >> +       cinfo->transport_info = vioch;
> >> +       vioch->cinfo = cinfo;
> >> +       spin_unlock_irqrestore(&vioch->lock, flags);
> >> +
> >> +       max_msg = virtio_get_max_msg(tx, cinfo);
> >> +
> >> +       for (i = 0; i < max_msg; i++) {
> >> +               struct scmi_vio_msg *msg;
> >> +
> >> +               msg = devm_kzalloc(cinfo->dev, sizeof(*msg), GFP_KERNEL);
> >> +               if (!msg)
> >> +                       return -ENOMEM;
> >> +
> >> +               if (tx) {
> >> +                       msg->request = devm_kzalloc(cinfo->dev,
> >> +                                                   VIRTIO_SCMI_MAX_PDU_SIZE,
> >> +                                                   GFP_KERNEL);
> >> +                       if (!msg->request)
> >> +                               return -ENOMEM;
> >> +               }
> >> +
> >> +               msg->input = devm_kzalloc(cinfo->dev, VIRTIO_SCMI_MAX_PDU_SIZE,
> >> +                                         GFP_KERNEL);
> >> +               if (!msg->input)
> >> +                       return -ENOMEM;
> >> +
> >> +               if (tx) {
> >> +                       spin_lock_irqsave(&vioch->lock, flags);
> >> +                       list_add_tail(&msg->list, &vioch->free_list);
> >> +                       spin_unlock_irqrestore(&vioch->lock, flags);
> >> +               } else {
> >> +                       scmi_vio_feed_vq_rx(vioch, msg);
> >> +               }
> >> +       }
> >> +
> >> +       spin_lock_irqsave(&vioch->ready_lock, flags);
> >> +       vioch->ready = true;
> >> +       spin_unlock_irqrestore(&vioch->ready_lock, flags);
> >> +
> >> +       return 0;
> >> +}
> >> +
> >> +static int virtio_chan_free(int id, void *p, void *data)
> >> +{
> >> +       unsigned long flags;
> >> +       struct scmi_chan_info *cinfo = p;
> >> +       struct scmi_vio_channel *vioch = cinfo->transport_info;
> >> +
> >> +       spin_lock_irqsave(&vioch->ready_lock, flags);
> >> +       vioch->ready = false;
> >> +       spin_unlock_irqrestore(&vioch->ready_lock, flags);
> >> +
> >> +       scmi_free_channel(cinfo, data, id);
> >> +       return 0;
> >> +}
> >> +
> >> +static int virtio_send_message(struct scmi_chan_info *cinfo,
> >> +                              struct scmi_xfer *xfer)
> >> +{
> >> +       struct scmi_vio_channel *vioch = cinfo->transport_info;
> >> +       struct scatterlist sg_out;
> >> +       struct scatterlist sg_in;
> >> +       struct scatterlist *sgs[DESCRIPTORS_PER_TX_MSG] = { &sg_out, &sg_in };
> >> +       unsigned long flags;
> >> +       int rc;
> >> +       struct scmi_vio_msg *msg;
> >> +
> >> +       /*
> >> +        * TODO: For now, we don't support polling. But it should not be
> >> +        * difficult to add support.
> >> +        */
> >> +       if (xfer->hdr.poll_completion)
> >> +               return -EINVAL;
> >> +
> >> +       spin_lock_irqsave(&vioch->lock, flags);
> >> +
> >> +       if (list_empty(&vioch->free_list)) {
> >> +               spin_unlock_irqrestore(&vioch->lock, flags);
> >> +               return -EBUSY;
> >> +       }
> >> +
> >> +       msg = list_first_entry(&vioch->free_list, typeof(*msg), list);
> >> +       list_del(&msg->list);
> >> +
> >> +       msg_tx_prepare(msg->request, xfer);
> >> +
> >> +       sg_init_one(&sg_out, msg->request, msg_command_size(xfer));
> >> +       sg_init_one(&sg_in, msg->input, msg_response_size(xfer));
> >> +
> >> +       rc = virtqueue_add_sgs(vioch->vqueue, sgs, 1, 1, msg, GFP_ATOMIC);
> >> +       if (rc) {
> >> +               list_add(&msg->list, &vioch->free_list);
> >> +               dev_err_once(vioch->cinfo->dev,
> >> +                            "%s() failed to add to virtqueue (%d)\n", __func__,
> >> +                            rc);
> >> +       } else {
> >> +               virtqueue_kick(vioch->vqueue);
> >> +       }
> >> +
> >> +       spin_unlock_irqrestore(&vioch->lock, flags);
> >> +
> >> +       return rc;
> >> +}
> >> +
> >> +static void virtio_fetch_response(struct scmi_chan_info *cinfo,
> >> +                                 struct scmi_xfer *xfer, void *msg_handle)
> >> +{
> >> +       struct scmi_vio_msg *msg = msg_handle;
> >> +       struct scmi_vio_channel *vioch = cinfo->transport_info;
> >> +
> >> +       if (!msg) {
> >> +               dev_dbg_once(&vioch->vqueue->vdev->dev,
> >> +                            "Ignoring %s() call with NULL msg_handle\n",
> >> +                            __func__);
> >> +               return;
> >> +       }
> >> +
> >> +       msg_fetch_response(msg->input, msg->rx_len, xfer);
> >> +}
> >> +
> >> +static void virtio_fetch_notification(struct scmi_chan_info *cinfo,
> >> +                                     size_t max_len, struct scmi_xfer *xfer,
> >> +                                     void *msg_handle)
> >> +{
> >> +       struct scmi_vio_msg *msg = msg_handle;
> >> +       struct scmi_vio_channel *vioch = cinfo->transport_info;
> >> +
> >> +       if (!msg) {
> >> +               dev_dbg_once(&vioch->vqueue->vdev->dev,
> >> +                            "Ignoring %s() call with NULL msg_handle\n",
> >> +                            __func__);
> >> +               return;
> >> +       }
> >> +
> >> +       msg_fetch_notification(msg->input, msg->rx_len, max_len, xfer);
> >> +}
> >> +
> >> +static void dummy_clear_channel(struct scmi_chan_info *cinfo)
> >> +{
> >> +}
> >> +
> >> +static bool dummy_poll_done(struct scmi_chan_info *cinfo,
> >> +                           struct scmi_xfer *xfer)
> >> +{
> >> +       return false;
> >> +}
> >> +
> >> +static void virtio_drop_message(struct scmi_chan_info *cinfo, void *msg_handle)
> >> +{
> >> +       unsigned long flags;
> >> +       struct scmi_vio_channel *vioch = cinfo->transport_info;
> >> +       struct scmi_vio_msg *msg = msg_handle;
> >> +
> >> +       if (!msg) {
> >> +               dev_dbg_once(&vioch->vqueue->vdev->dev,
> >> +                            "Ignoring %s() call with NULL msg_handle\n",
> >> +                            __func__);
> >> +               return;
> >> +       }
> >> +
> >> +       if (vioch->is_rx) {
> >> +               scmi_vio_feed_vq_rx(vioch, msg);
> >> +       } else {
> >> +               spin_lock_irqsave(&vioch->lock, flags);
> >> +               list_add(&msg->list, &vioch->free_list);
> >> +               spin_unlock_irqrestore(&vioch->lock, flags);
> >> +       }
> >> +}
> >> +
> >> +static const struct scmi_transport_ops scmi_virtio_ops = {
> >> +       .link_supplier = virtio_link_supplier,
> >> +       .chan_available = virtio_chan_available,
> >> +       .chan_setup = virtio_chan_setup,
> >> +       .chan_free = virtio_chan_free,
> >> +       .get_max_msg = virtio_get_max_msg,
> >> +       .send_message = virtio_send_message,
> >> +       .fetch_response = virtio_fetch_response,
> >> +       .fetch_notification = virtio_fetch_notification,
> >> +       .clear_channel = dummy_clear_channel,
> >> +       .poll_done = dummy_poll_done,
> >> +       .drop_message = virtio_drop_message,
> >> +};
> >> +
> >> +static int scmi_vio_probe(struct virtio_device *vdev)
> >> +{
> >> +       struct device *dev = &vdev->dev;
> >> +       struct scmi_vio_channel *channels;
> >> +       bool have_vq_rx;
> >> +       int vq_cnt;
> >> +       int i;
> >> +       int ret;
> >> +       struct virtqueue *vqs[VIRTIO_SCMI_VQ_MAX_CNT];
> >> +
> >> +       have_vq_rx = scmi_vio_have_vq_rx(vdev);
> >> +       vq_cnt = have_vq_rx ? VIRTIO_SCMI_VQ_MAX_CNT : 1;
> >> +
> >> +       channels = devm_kcalloc(dev, vq_cnt, sizeof(*channels), GFP_KERNEL);
> >> +       if (!channels)
> >> +               return -ENOMEM;
> >> +
> >> +       if (have_vq_rx)
> >> +               channels[VIRTIO_SCMI_VQ_RX].is_rx = true;
> >> +
> >> +       ret = virtio_find_vqs(vdev, vq_cnt, vqs, scmi_vio_complete_callbacks,
> >> +                             scmi_vio_vqueue_names, NULL);
> >> +       if (ret) {
> >> +               dev_err(dev, "Failed to get %d virtqueue(s)\n", vq_cnt);
> >> +               return ret;
> >> +       }
> >> +       dev_info(dev, "Found %d virtqueue(s)\n", vq_cnt);
> >> +
> >> +       for (i = 0; i < vq_cnt; i++) {
> >> +               spin_lock_init(&channels[i].lock);
> >> +               spin_lock_init(&channels[i].ready_lock);
> >> +               INIT_LIST_HEAD(&channels[i].free_list);
> >> +               channels[i].vqueue = vqs[i];
> >> +       }
> >> +
> >> +       vdev->priv = channels;
> >> +
> >> +       return 0;
> >> +}
> >> +
> >> +static void scmi_vio_remove(struct virtio_device *vdev)
> >> +{
> >> +       vdev->config->reset(vdev);
> >> +       vdev->config->del_vqs(vdev);
> >> +}
> >> +
> >> +static unsigned int features[] = {
> >> +       VIRTIO_SCMI_F_P2A_CHANNELS,
> >> +};
> >> +
> >> +static const struct virtio_device_id id_table[] = {
> >> +       { VIRTIO_ID_SCMI, VIRTIO_DEV_ANY_ID },
> >> +       { 0 }
> >> +};
> >> +
> >> +static struct virtio_driver virtio_scmi_driver = {
> >> +       .driver.name = "scmi-virtio",
> >> +       .driver.owner = THIS_MODULE,
> >> +       .feature_table = features,
> >> +       .feature_table_size = ARRAY_SIZE(features),
> >> +       .id_table = id_table,
> >> +       .probe = scmi_vio_probe,
> >> +       .remove = scmi_vio_remove,
> >> +};
> >> +
> >> +static int __init virtio_scmi_init(void)
> >> +{
> >> +       return register_virtio_driver(&virtio_scmi_driver);
> >> +}
> >> +
> >> +static void __exit virtio_scmi_exit(void)
> >> +{
> >> +       unregister_virtio_driver(&virtio_scmi_driver);
> >> +}
> >> +
> >> +const struct scmi_desc scmi_virtio_desc = {
> >> +       .init = virtio_scmi_init,
> >> +       .exit = virtio_scmi_exit,
> >> +       .ops = &scmi_virtio_ops,
> >> +       .max_rx_timeout_ms = 60000, /* for non-realtime virtio devices */
> >> +       .max_msg = 0, /* overridden by virtio_get_max_msg() */
> >> +       .max_msg_size = VIRTIO_SCMI_MAX_MSG_SIZE,
> >> +};
> >> diff --git a/include/uapi/linux/virtio_ids.h b/include/uapi/linux/virtio_ids.h
> >> index f0c35ce8628c..c146fe30e589 100644
> >> --- a/include/uapi/linux/virtio_ids.h
> >> +++ b/include/uapi/linux/virtio_ids.h
> >> @@ -56,5 +56,6 @@
> >>  #define VIRTIO_ID_PMEM                 27 /* virtio pmem */
> >>  #define VIRTIO_ID_BT                   28 /* virtio bluetooth */
> >>  #define VIRTIO_ID_MAC80211_HWSIM       29 /* virtio mac80211-hwsim */
> >> +#define VIRTIO_ID_SCMI                 32 /* virtio SCMI */
> >>
> >>  #endif /* _LINUX_VIRTIO_IDS_H */
> >> diff --git a/include/uapi/linux/virtio_scmi.h b/include/uapi/linux/virtio_scmi.h
> >> new file mode 100644
> >> index 000000000000..732b01504c35
> >> --- /dev/null
> >> +++ b/include/uapi/linux/virtio_scmi.h
> >> @@ -0,0 +1,25 @@
> >> +/* SPDX-License-Identifier: ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) */
> >> +/*
> >> + * Copyright (C) 2020 OpenSynergy GmbH
> >> + */
> >> +
> >> +#ifndef _UAPI_LINUX_VIRTIO_SCMI_H
> >> +#define _UAPI_LINUX_VIRTIO_SCMI_H
> >> +
> >> +#include <linux/virtio_types.h>
> >> +
> >> +/* Feature bits */
> >> +
> >> +/* Device implements some SCMI notifications, or delayed responses. */
> >> +#define VIRTIO_SCMI_F_P2A_CHANNELS 0
> >> +
> >> +/* Device implements any SCMI statistics shared memory region */
> >> +#define VIRTIO_SCMI_F_SHARED_MEMORY 1
> >> +
> >> +/* Virtqueues */
> >> +
> >> +#define VIRTIO_SCMI_VQ_TX 0 /* cmdq */
> >> +#define VIRTIO_SCMI_VQ_RX 1 /* eventq */
> >> +#define VIRTIO_SCMI_VQ_MAX_CNT 2
> >> +
> >> +#endif /* _UAPI_LINUX_VIRTIO_SCMI_H */
> >> --
> >> 2.25.1
> >>
> >>
> >
>
>