[PATCH net-next v4 00/10] Adding the Sparx5 Switch Driver

[Steen Hegelund]

This series provides the Microchip Sparx5 Switch Driver

The Sparx5 Carrier Ethernet and Industrial switch family delivers 64
Ethernet ports and up to 200 Gbps of switching bandwidth.

It provides a rich set of Ethernet switching features such as hierarchical
QoS, hardware-based OAM  and service activation testing, protection
switching, IEEE 1588, and Synchronous Ethernet.

Using provider bridging (Q-in-Q) and MPLS/MPLS-TP technology, it delivers
MEF CE
2.0 Ethernet virtual connections (EVCs) and features advanced TCAM
  classification in both ingress and egress.

Per-EVC features include advanced L3-aware classification, a rich set of
statistics, OAM for end-to-end performance monitoring, and dual-rate
policing and shaping.

Time sensitive networking (TSN) is supported through a comprehensive set of
features including frame preemption, cut-through, frame replication and
elimination for reliability, enhanced scheduling: credit-based shaping,
time-aware shaping, cyclic queuing, and forwarding, and per-stream policing
and filtering.

Together with IEEE 1588 and IEEE 802.1AS support, this guarantees
low-latency deterministic networking for Fronthaul, Carrier, and Industrial
Ethernet.

The Sparx5 switch family consists of following SKUs:

- VSC7546 Sparx5-64 up to 64 Gbps of bandwidth with the following primary
  port configurations:
  - 6 *10G
  - 16 * 2.5G + 2 * 10G
  - 24 * 1G + 4 * 10G

- VSC7549 Sparx5-90 up to 90 Gbps of bandwidth with the following primary
  port configurations:
  - 9 * 10G
  - 16 * 2.5G + 4 * 10G
  - 48 * 1G + 4 * 10G

- VSC7552 Sparx5-128 up to 128 Gbps of bandwidth with the following primary
  port configurations:
  - 12 * 10G
  - 16 * 2.5G + 8 * 10G
  - 48 * 1G + 8 * 10G

- VSC7556 Sparx5-160 up to 160 Gbps of bandwidth with the following primary
  port configurations:
  - 16 * 10G
  - 10 * 10G + 2 * 25G
  - 16 * 2.5G + 10 * 10G
  - 48 * 1G + 10 * 10G

- VSC7558 Sparx5-200 up to 200 Gbps of bandwidth with the following primary
  port configurations:
  - 20 * 10G
  - 8 * 25G

In addition, the device supports one 10/100/1000/2500/5000 Mbps
SGMII/SerDes node processor interface (NPI) Ethernet port.

The Sparx5 support is developed on the PCB134 and PCB135 evaluation boards.

- PCB134 main networking features:
  - 12x SFP+ front 10G module slots (connected to Sparx5 through SFI).
  - 8x SFP28 front 25G module slots (connected to Sparx5 through SFI high
    speed).
  - Optional, one additional 10/100/1000BASE-T (RJ45) Ethernet port
    (on-board VSC8211 PHY connected to Sparx5 through SGMII).

- PCB135 main networking features:
  - 48x1G (10/100/1000M) RJ45 front ports using 12xVSC8514 QuadPHY’s each
    connected to VSC7558 through QSGMII.
  - 4x10G (1G/2.5G/5G/10G) RJ45 front ports using the AQR407 10G QuadPHY
    each port connects to VSC7558 through SFI.
  - 4x SFP28 25G module slots on back connected to VSC7558 through SFI high
    speed.
  - Optional, one additional 1G (10/100/1000M) RJ45 port using an on-board
    VSC8211 PHY, which can be connected to VSC7558 NPI port through SGMII
    using a loopback add-on PCB)

This series provides support for:
  - SFPs and DAC cables via PHYLINK with a number of 5G, 10G and 25G
    devices and media types.
  - Port module configuration for 10M to 25G speeds with SGMII, QSGMII,
    1000BASEX, 2500BASEX and 10GBASER as appropriate for these modes.
  - SerDes configuration via the Sparx5 SerDes driver (see below).
  - Host mode providing register based injection and extraction.
  - Switch mode providing MAC/VLAN table learning and Layer2 switching
    offloaded to the Sparx5 switch.
  - STP state, VLAN support, host/bridge port mode, Forwarding DB, and
    configuration and statistics via ethtool.

More support will be added at a later stage.

The Sparx5 Chip Register Model can be browsed at this location:
https://github.com/microchip-ung/sparx-5_reginfo
and the datasheet is available here:
https://ww1.microchip.com/downloads/en/DeviceDoc/SparX-5_Family_L2L3_Enterprise_10G_Ethernet_Switches_Datasheet_00003822B.pdf

The series depends on the following series currently on their way
into the kernel:

- 25G Base-R phy mode
  Link: https://lore.kernel.org/r/20210611125453.313308-1-steen.hegelund@xxxxxxxxxxxxx/
- Sparx5 Reset Driver
  Link: https://lore.kernel.org/r/20210416084054.2922327-1-steen.hegelund@xxxxxxxxxxxxx/

ChangeLog:
v4:
    - basic driver:
        Using devm_reset_control_get_optional_shared to get the reset
        control, and let the reset framework check if it is valid.
    - host mode (phylink):
        Use the PCS operations to get state and update configuration.
        Removed the setting of interface modes.  Let phylink control this.
        Using the new 5gbase-r and 25gbase-r modes.
        Using a helper function to check if one of the 3 base-r modes has
        been selected.
        Currently it will not be possible to change the interface mode by
        changing the speed (e.g via ethtool).  This will be added later.
v3:
    - basic driver:
        - removed unneeded braces
        - release reference to ports node after use
        - use dev_err_probe to handle DEFER
        - update error value when bailing out (a few cases)
        - updated formatting of port struct and grouping of bool values
        - simplified the spx5_rmw and spx5_inst_rmw inline functions
    - host mode (netdev):
        - removed lockless flag
        - added port timer init
    - host mode (packet - manual injection):
        - updated error counters in error situations
        - implemented timer handling of watermark threshold: stop and
          restart netif queues.
        - fixed error message handling (rate limited)
        - fixed comment style error
        - used DIV_ROUND_UP macro
        - removed a debug message for open ports

v2:
    - Updated bindings:
        - drop minItems for the reg property
    - Statistics implementation:
        - Reorganized statistics into ethtool groups:
            eth-phy, eth-mac, eth-ctrl, rmon
          as defined by the IEEE 802.3 categories and RFC 2819.
        - The remaining statistics are provided by the classic ethtool
          statistics command.
    - Hostmode support:
        - Removed netdev renaming
        - Validate ethernet address in sparx5_set_mac_address()

Steen Hegelund (10):
  dt-bindings: net: sparx5: Add sparx5-switch bindings
  net: sparx5: add the basic sparx5 driver
  net: sparx5: add hostmode with phylink support
  net: sparx5: add port module support
  net: sparx5: add mactable support
  net: sparx5: add vlan support
  net: sparx5: add switching support
  net: sparx5: add calendar bandwidth allocation support
  net: sparx5: add ethtool configuration and statistics support
  arm64: dts: sparx5: Add the Sparx5 switch node

 .../bindings/net/microchip,sparx5-switch.yaml |  226 +
 arch/arm64/boot/dts/microchip/sparx5.dtsi     |   94 +-
 .../dts/microchip/sparx5_pcb134_board.dtsi    |  481 +-
 .../dts/microchip/sparx5_pcb135_board.dtsi    |  621 ++-
 drivers/net/ethernet/microchip/Kconfig        |    2 +
 drivers/net/ethernet/microchip/Makefile       |    2 +
 drivers/net/ethernet/microchip/sparx5/Kconfig |    9 +
 .../net/ethernet/microchip/sparx5/Makefile    |   10 +
 .../microchip/sparx5/sparx5_calendar.c        |  596 +++
 .../microchip/sparx5/sparx5_ethtool.c         | 1227 +++++
 .../microchip/sparx5/sparx5_mactable.c        |  500 ++
 .../ethernet/microchip/sparx5/sparx5_main.c   |  857 +++
 .../ethernet/microchip/sparx5/sparx5_main.h   |  373 ++
 .../microchip/sparx5/sparx5_main_regs.h       | 4642 +++++++++++++++++
 .../ethernet/microchip/sparx5/sparx5_netdev.c |  249 +
 .../ethernet/microchip/sparx5/sparx5_packet.c |  320 ++
 .../microchip/sparx5/sparx5_phylink.c         |  209 +
 .../ethernet/microchip/sparx5/sparx5_port.c   | 1149 ++++
 .../ethernet/microchip/sparx5/sparx5_port.h   |   93 +
 .../microchip/sparx5/sparx5_switchdev.c       |  508 ++
 .../ethernet/microchip/sparx5/sparx5_vlan.c   |  224 +
 21 files changed, 12308 insertions(+), 84 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml
 create mode 100644 drivers/net/ethernet/microchip/sparx5/Kconfig
 create mode 100644 drivers/net/ethernet/microchip/sparx5/Makefile
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_calendar.c
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_ethtool.c
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_mactable.c
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_main.c
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_main.h
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_main_regs.h
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_netdev.c
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_packet.c
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_phylink.c
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_port.c
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_port.h
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
 create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_vlan.c

-- 
2.32.0