Re: [PATCH 1/3] riscv: optimized memcpy

[Matteo Croce]

On Thu, Jun 17, 2021 at 11:48 PM Matteo Croce
<mcroce@xxxxxxxxxxxxxxxxxxx> wrote:
>
> On Thu, Jun 17, 2021 at 11:30 PM David Laight <David.Laight@xxxxxxxxxx> wrote:
> >
> > From: Matteo Croce
> > > Sent: 16 June 2021 19:52
> > > To: Guo Ren <guoren@xxxxxxxxxx>
> > >
> > > On Wed, Jun 16, 2021 at 1:46 PM Guo Ren <guoren@xxxxxxxxxx> wrote:
> > > >
> > > > Hi Matteo,
> > > >
> > > > Have you tried Glibc generic implementation code?
> > > > ref: https://lore.kernel.org/linux-arch/20190629053641.3iBfk9-
> > > I_D29cDp9yJnIdIg7oMtHNZlDmhLQPTumhEc@z/#t
> > > >
> > > > If Glibc codes have the same performance in your hardware, then you
> > > > could give a generic implementation first.
> >
> > Isn't that a byte copy loop - the performance of that ought to be terrible.
> > ...
> >
> > > I had a look, it seems that it's a C unrolled version with the
> > > 'register' keyword.
> > > The same one was already merged in nios2:
> > > https://elixir.bootlin.com/linux/latest/source/arch/nios2/lib/memcpy.c#L68
> >
> > I know a lot about the nios2 instruction timings.
> > (I've looked at code execution in the fpga's intel 'logic analiser.)
> > It is a very simple 4-clock pipeline cpu with a 2-clock delay
> > before a value read from 'tightly coupled memory' (aka cache)
> > can be used in another instruction.
> > There is also a subtle pipeline stall if a read follows a write
> > to the same memory block because the write is executed one
> > clock later - and would collide with the read.
> > Since it only ever executes one instruction per clock loop
> > unrolling does help - since you never get the loop control 'for free'.
> > OTOH you don't need to use that many registers.
> > But an unrolled loop should approach 2 bytes/clock (32bit cpu).
> >
> > > I copied _wordcopy_fwd_aligned() from Glibc, and I have a very similar
> > > result of the other versions:
> > >
> > > [  563.359126] Strings selftest: memcpy(src+7, dst+7): 257 Mb/s
> >
> > What clock speed is that running at?
> > It seems very slow for a 64bit cpu (that isn't an fpga soft-cpu).
> >
> > While the small riscv cpu might be similar to the nios2 (and mips
> > for that matter), there are also bigger/faster cpu.
> > I'm sure these can execute multiple instructions/clock
> > and possible even read and write at the same time.
> > Unless they also support significant instruction re-ordering
> > the trivial copy loops are going to be slow on such cpu.
> >
>
> It's running at 1 GHz.
>
> I get 257 Mb/s with a memcpy, a bit more with a memset,
> but I get 1200 Mb/s with a cyle which just reads memory with 64 bit addressing.
>

Err, I forget a mlock() before accessing the memory in userspace.

The real speed here is:

8 bit read: 155.42 Mb/s
64 bit read: 277.29 Mb/s
8 bit write: 138.57 Mb/s
64 bit write: 239.21 Mb/s

-- 
per aspera ad upstream