Re: [PATCH net-next v2 4/8] net: usb: asix: ax88772: add phylib support

[Oleksij Rempel]

On Fri, Jun 18, 2021 at 01:11:41PM +0200, Marek Szyprowski wrote:
> Hi Heiner,
> 
> On 18.06.2021 13:04, Heiner Kallweit wrote:
> > On 18.06.2021 12:13, Oleksij Rempel wrote:
> >> thank you for your feedback.
> >>
> >> On Fri, Jun 18, 2021 at 10:39:12AM +0200, Marek Szyprowski wrote:
> >>> On 07.06.2021 10:27, Oleksij Rempel wrote:
> >>>> To be able to use ax88772 with external PHYs and use advantage of
> >>>> existing PHY drivers, we need to port at least ax88772 part of asix
> >>>> driver to the phylib framework.
> >>>>
> >>>> Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
> >>> I found one more issue with this patch. On one of my test boards
> >>> (Samsung Exynos5250 SoC based Arndale) system fails to establish network
> >>> connection just after starting the kernel when the driver is build-in.
> >>>
> > If you build in the MAC driver, do you also build in the PHY driver?
> > If the PHY driver is still a module this could explain why genphy
> > driver is used.
> > And your dmesg filtering suppresses the phy_attached_info() output
> > that would tell us the truth.
> 
> Here is a bit more complete log:
> 
> # dmesg | grep -i Asix
> [    2.412966] usbcore: registered new interface driver asix
> [    4.620094] usb 1-3.2.4: Manufacturer: ASIX Elec. Corp.
> [    4.641797] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): 
> invalid hw address, using random
> [    5.657009] libphy: Asix MDIO Bus: probed
> [    5.750584] Asix Electronics AX88772A usb-001:004:10: attached PHY 
> driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL)
> [    5.763908] asix 1-3.2.4:1.0 eth0: register 'asix' at 
> usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, fe:a5:29:e2:97:3e
> [    9.090270] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow 
> control off
> 
> This seems to be something different than missing PHY driver.

Can you please test it:

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index aec97b021a73..7897108a1a42 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -453,6 +453,7 @@ static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
 	u16 rx_ctl, phy14h, phy15h, phy16h;
 	u8 chipcode = 0;
 
+	netdev_info(dev->net, "ax88772a_hw_reset\n");
 	ret = asix_write_gpio(dev, AX_GPIO_RSE, 5, in_pm);
 	if (ret < 0)
 		goto out;
@@ -509,31 +510,7 @@ static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
 			goto out;
 		}
 	} else if ((chipcode & AX_CHIPCODE_MASK) == AX_AX88772A_CHIPCODE) {
-		/* Check if the PHY registers have default settings */
-		phy14h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
-					     AX88772A_PHY14H);
-		phy15h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
-					     AX88772A_PHY15H);
-		phy16h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
-					     AX88772A_PHY16H);
-
-		netdev_dbg(dev->net,
-			   "772a_hw_reset: MR20=0x%x MR21=0x%x MR22=0x%x\n",
-			   phy14h, phy15h, phy16h);
-
-		/* Restore PHY registers default setting if not */
-		if (phy14h != AX88772A_PHY14H_DEFAULT)
-			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
-					     AX88772A_PHY14H,
-					     AX88772A_PHY14H_DEFAULT);
-		if (phy15h != AX88772A_PHY15H_DEFAULT)
-			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
-					     AX88772A_PHY15H,
-					     AX88772A_PHY15H_DEFAULT);
-		if (phy16h != AX88772A_PHY16H_DEFAULT)
-			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
-					     AX88772A_PHY16H,
-					     AX88772A_PHY16H_DEFAULT);
+		netdev_info(dev->net, "do not touch PHY regs\n");
 	}
 
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |