Re: [PATCH v4] arm pl011 serial: support multi-irq request

[Greg KH]

On Wed, Jun 30, 2021 at 07:25:05PM +0800, Bing Fan wrote:
> From: Bing Fan <tombinfan@xxxxxxxxxxx>
> 
> In order to make pl011 work better, multiple interrupts are
> required, such as TXIM, RXIM, RTIM, error interrupt(FE/PE/BE/OE);
> at the same time, pl011 to GIC does not merge the interrupt
> lines(each serial-interrupt corresponding to different GIC hardware
> interrupt), so need to enable and request multiple gic interrupt
> numbers in the driver.
> 
> Signed-off-by: Bing Fan <tombinfan@xxxxxxxxxxx>
> ---
>  drivers/tty/serial/amba-pl011.c | 35 ++++++++++++++++++++++++++++++---
>  1 file changed, 32 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
> index 78682c12156a..e84f4b9dff87 100644
> --- a/drivers/tty/serial/amba-pl011.c
> +++ b/drivers/tty/serial/amba-pl011.c
> @@ -1701,11 +1701,40 @@ static void pl011_write_lcr_h(struct uart_amba_port *uap, unsigned int lcr_h)
>  	}
>  }
>  
> +static void pl011_release_irq(struct uart_amba_port *uap, unsigned int max_cnt)
> +{
> +	struct amba_device *amba_dev = container_of(uap->port.dev, struct amba_device, dev);

Pass in the amba_dev instead here, you already have a pointer to it at
all places, right?

> +	int i;
> +
> +	for (i = 0; i < max_cnt; i++) {
> +		if (amba_dev->irq[i])
> +			free_irq(amba_dev->irq[i], uap);
> +	}

You do not need { } here, didn't checkpatch warn about this?

> +}
> +
>  static int pl011_allocate_irq(struct uart_amba_port *uap)
>  {
> +	int ret = 0;
> +	int i;
> +	unsigned int virq;
> +	struct amba_device *amba_dev = container_of(uap->port.dev, struct amba_device, dev);
> +
>  	pl011_write(uap->im, uap, REG_IMSC);
>  
> -	return request_irq(uap->port.irq, pl011_int, IRQF_SHARED, "uart-pl011", uap);
> +	for (i = 0; i < AMBA_NR_IRQS; i++) {
> +		virq = amba_dev->irq[i];
> +		if (virq == 0)
> +			break;
> +
> +		ret = request_irq(virq, pl011_int, IRQF_SHARED, dev_name(&amba_dev->dev), uap);
> +		if (ret) {
> +			dev_err(uap->port.dev, "request %u interrupt failed\n", virq);
> +			pl011_release_irq(uap, i - 1);
> +			break;
> +		}
> +	}
> +
> +	return ret;
>  }
>  
>  /*
> @@ -1864,7 +1893,7 @@ static void pl011_shutdown(struct uart_port *port)
>  
>  	pl011_dma_shutdown(uap);
>  
> -	free_irq(uap->port.irq, uap);
> +	pl011_release_irq(uap, AMBA_NR_IRQS);

Ah, so your original patch was not correct either, how well have you
tested these changes?

thanks,

greg k-h