Re: [PATCH v4 2/3] PCI: visconti: Add Toshiba Visconti PCIe host controller driver

From: Rob Herring
Date: Thu Jul 01 2021 - 11:44:06 EST

Next message: Bjorn Helgaas: "Re: [PATCH 0/4] PCI: replace dublicated MRRS limit quirks"
Previous message: 권오훈: "RE: [PATCH] mm: sparse: pass section_nr to section_mark_present"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Tue, Jun 29, 2021 at 5:50 PM Nobuhiro Iwamatsu
<nobuhiro1.iwamatsu@xxxxxxxxxxxxx> wrote:
>
> Add support to PCIe RC controller on Toshiba Visconti ARM SoCs. PCIe
> controller is based of Synopsys DesignWare PCIe core.
>
> This patch does not yet use the clock framework to control the clock.
> This will be replaced in the future.
>
> Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@xxxxxxxxxxxxx>
> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@xxxxxxxxxxxxx>
> ---
> drivers/pci/controller/dwc/Kconfig | 9 +
> drivers/pci/controller/dwc/Makefile | 1 +
> drivers/pci/controller/dwc/pcie-visconti.c | 360 +++++++++++++++++++++
> 3 files changed, 370 insertions(+)
> create mode 100644 drivers/pci/controller/dwc/pcie-visconti.c
>
> diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> index 423d35872ce4..7c3dcb86fcad 100644
> --- a/drivers/pci/controller/dwc/Kconfig
> +++ b/drivers/pci/controller/dwc/Kconfig
> @@ -286,6 +286,15 @@ config PCIE_TEGRA194_EP
> in order to enable device-specific features PCIE_TEGRA194_EP must be
> selected. This uses the DesignWare core.
>
> +config PCIE_VISCONTI_HOST
> + bool "Toshiba Visconti PCIe controllers"
> + depends on ARCH_VISCONTI || COMPILE_TEST
> + depends on PCI_MSI_IRQ_DOMAIN
> + select PCIE_DW_HOST
> + help
> + Say Y here if you want PCIe controller support on Toshiba Visconti SoC.
> + This driver supports TMPV7708 SoC.
> +
> config PCIE_UNIPHIER
> bool "Socionext UniPhier PCIe host controllers"
> depends on ARCH_UNIPHIER || COMPILE_TEST
> diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
> index eca805c1a023..0b569d54deb3 100644
> --- a/drivers/pci/controller/dwc/Makefile
> +++ b/drivers/pci/controller/dwc/Makefile
> @@ -20,6 +20,7 @@ obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
> obj-$(CONFIG_PCI_MESON) += pci-meson.o
> obj-$(CONFIG_PCIE_UNIPHIER) += pcie-uniphier.o
> obj-$(CONFIG_PCIE_UNIPHIER_EP) += pcie-uniphier-ep.o
> +obj-$(CONFIG_PCIE_VISCONTI_HOST) += pcie-visconti.o
>
> # The following drivers are for devices that use the generic ACPI
> # pci_root.c driver but don't support standard ECAM config access.
> diff --git a/drivers/pci/controller/dwc/pcie-visconti.c b/drivers/pci/controller/dwc/pcie-visconti.c
> new file mode 100644
> index 000000000000..1e1caa2ba1b6
> --- /dev/null
> +++ b/drivers/pci/controller/dwc/pcie-visconti.c
> @@ -0,0 +1,360 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * DWC PCIe RC driver for Toshiba Visconti ARM SoC
> + *
> + * Copyright (C) 2021 Toshiba Electronic Device & Storage Corporation
> + * Copyright (C) 2021 TOSHIBA CORPORATION
> + *
> + * Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@xxxxxxxxxxxxx>
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/gpio.h>
> +#include <linux/interrupt.h>
> +#include <linux/init.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/of_platform.h>
> +#include <linux/pci.h>
> +#include <linux/platform_device.h>
> +#include <linux/resource.h>
> +#include <linux/types.h>
> +
> +#include "pcie-designware.h"
> +#include "../../pci.h"
> +
> +struct visconti_pcie {
> + struct dw_pcie pci;
> + void __iomem *ulreg_base;
> + void __iomem *smu_base;
> + void __iomem *mpu_base;
> + struct clk *refclk;
> + struct clk *coreclk;
> + struct clk *auxclk;
> +};
> +
> +#define PCIE_UL_REG_S_PCIE_MODE 0x00F4
> +#define PCIE_UL_REG_S_PCIE_MODE_EP 0x00
> +#define PCIE_UL_REG_S_PCIE_MODE_RC 0x04
> +
> +#define PCIE_UL_REG_S_PERSTN_CTRL 0x00F8
> +#define PCIE_UL_IOM_PCIE_PERSTN_I_EN BIT(3)
> +#define PCIE_UL_DIRECT_PERSTN_EN BIT(2)
> +#define PCIE_UL_PERSTN_OUT BIT(1)
> +#define PCIE_UL_DIRECT_PERSTN BIT(0)
> +#define PCIE_UL_REG_S_PERSTN_CTRL_INIT (PCIE_UL_IOM_PCIE_PERSTN_I_EN | \
> + PCIE_UL_DIRECT_PERSTN_EN | \
> + PCIE_UL_DIRECT_PERSTN)
> +
> +#define PCIE_UL_REG_S_PHY_INIT_02 0x0104
> +#define PCIE_UL_PHY0_SRAM_EXT_LD_DONE BIT(0)
> +
> +#define PCIE_UL_REG_S_PHY_INIT_03 0x0108
> +#define PCIE_UL_PHY0_SRAM_INIT_DONE BIT(0)
> +
> +#define PCIE_UL_REG_S_INT_EVENT_MASK1 0x0138
> +#define PCIE_UL_CFG_PME_INT BIT(0)
> +#define PCIE_UL_CFG_LINK_EQ_REQ_INT BIT(1)
> +#define PCIE_UL_EDMA_INT0 BIT(2)
> +#define PCIE_UL_EDMA_INT1 BIT(3)
> +#define PCIE_UL_EDMA_INT2 BIT(4)
> +#define PCIE_UL_EDMA_INT3 BIT(5)
> +#define PCIE_UL_S_INT_EVENT_MASK1_ALL (PCIE_UL_CFG_PME_INT | \
> + PCIE_UL_CFG_LINK_EQ_REQ_INT | \
> + PCIE_UL_EDMA_INT0 | \
> + PCIE_UL_EDMA_INT1 | \
> + PCIE_UL_EDMA_INT2 | \
> + PCIE_UL_EDMA_INT3)
> +
> +#define PCIE_UL_REG_S_SB_MON 0x0198
> +#define PCIE_UL_REG_S_SIG_MON 0x019C
> +#define PCIE_UL_CORE_RST_N_MON BIT(0)
> +
> +#define PCIE_UL_REG_V_SII_DBG_00 0x0844
> +#define PCIE_UL_REG_V_SII_GEN_CTRL_01 0x0860
> +#define PCIE_UL_APP_LTSSM_ENABLE BIT(0)
> +
> +#define PCIE_UL_REG_V_PHY_ST_00 0x0864
> +#define PCIE_UL_SMLH_LINK_UP BIT(0)
> +
> +#define PCIE_UL_REG_V_PHY_ST_02 0x0868
> +#define PCIE_UL_S_DETECT_ACT 0x01
> +#define PCIE_UL_S_L0 0x11
> +
> +#define PISMU_CKON_PCIE 0x0038
> +#define PISMU_CKON_PCIE_AUX_CLK BIT(1)
> +#define PISMU_CKON_PCIE_MSTR_ACLK BIT(0)
> +
> +#define PISMU_RSOFF_PCIE 0x0538
> +#define PISMU_RSOFF_PCIE_ULREG_RST_N BIT(1)
> +#define PISMU_RSOFF_PCIE_PWR_UP_RST_N BIT(0)
> +
> +#define PCIE_MPU_REG_MP_EN 0x0
> +#define MPU_MP_EN_DISABLE BIT(0)
> +
> +#define PCIE_BUS_OFFSET 0x40000000
> +
> +/* Access registers in PCIe ulreg */
> +static void visconti_ulreg_writel(struct visconti_pcie *pcie, u32 val, u32 reg)
> +{
> + writel_relaxed(val, pcie->ulreg_base + reg);
> +}
> +
> +static u32 visconti_ulreg_readl(struct visconti_pcie *pcie, u32 reg)
> +{
> + return readl_relaxed(pcie->ulreg_base + reg);
> +}
> +
> +/* Access registers in PCIe smu */
> +static void visconti_smu_writel(struct visconti_pcie *pcie, u32 val, u32 reg)
> +{
> + writel_relaxed(val, pcie->smu_base + reg);
> +}
> +
> +/* Access registers in PCIe mpu */
> +static void visconti_mpu_writel(struct visconti_pcie *pcie, u32 val, u32 reg)
> +{
> + writel_relaxed(val, pcie->mpu_base + reg);
> +}
> +
> +static u32 visconti_mpu_readl(struct visconti_pcie *pcie, u32 reg)
> +{
> + return readl_relaxed(pcie->mpu_base + reg);
> +}
> +
> +static int visconti_pcie_link_up(struct dw_pcie *pci)
> +{
> + struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
> + void __iomem *addr = pcie->ulreg_base;
> + int ret;
> + u32 val;
> +
> + /* wait for linkup of phy link layer */
> + ret = readl_relaxed_poll_timeout(addr + PCIE_UL_REG_V_PHY_ST_00,
> + val, (val & PCIE_UL_SMLH_LINK_UP),
> + 90000, 100000);

This function is really supposed to be 'is the link up or not', not
'wait for link up' as that is what the caller does. Isn't link up just
all 3 register bits are set? And it is possible for the 3rd bit
(PCIE_UL_S_L0) to be set without the first 2 bits set? IOW, can't you
just check PCIE_UL_S_L0?

> + if (ret)
> + return 0;
> +
> + /* wait for linkup of data link layer */
> + ret = readl_relaxed_poll_timeout(addr + PCIE_UL_REG_V_PHY_ST_02,
> + val, (val & PCIE_UL_S_DETECT_ACT),
> + 90000, 100000);
> + if (ret)
> + return 0;
> +
> + /* wait for LTSSM Status */
> + ret = readl_relaxed_poll_timeout(addr + PCIE_UL_REG_V_PHY_ST_02,
> + val, (val & PCIE_UL_S_L0),
> + 90000, 100000);
> + if (ret)
> + return 0;
> + return 1;
> +}
> +
> +static int visconti_pcie_start_link(struct dw_pcie *pci)
> +{
> + struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
> +
> + visconti_ulreg_writel(pcie, PCIE_UL_APP_LTSSM_ENABLE,
> + PCIE_UL_REG_V_SII_GEN_CTRL_01);
> +
> + if (dw_pcie_link_up(pci)) {
> + u32 val;
> +
> + val = visconti_mpu_readl(pcie, PCIE_MPU_REG_MP_EN);
> + visconti_mpu_writel(pcie, val & ~MPU_MP_EN_DISABLE,
> + PCIE_MPU_REG_MP_EN);
> + visconti_ulreg_writel(pcie, PCIE_UL_S_INT_EVENT_MASK1_ALL,
> + PCIE_UL_REG_S_INT_EVENT_MASK1);

Do these really have to be set after link up?

> + }
> +
> + return 0;
> +}
> +
> +static void visconti_pcie_stop_link(struct dw_pcie *pci)
> +{
> + struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
> + u32 val;
> +
> + val = visconti_ulreg_readl(pcie, PCIE_UL_REG_V_SII_GEN_CTRL_01);
> + val &= ~PCIE_UL_APP_LTSSM_ENABLE;
> + visconti_ulreg_writel(pcie, val, PCIE_UL_REG_V_SII_GEN_CTRL_01);
> +
> + val = visconti_mpu_readl(pcie, PCIE_MPU_REG_MP_EN);
> + visconti_mpu_writel(pcie, val | MPU_MP_EN_DISABLE, PCIE_MPU_REG_MP_EN);
> +}
> +
> +/*
> + * In this SoC specification, the CPU bus outputs the offset value from
> + * 0x40000000 to the PCIE bus, so 0x40000000 is subtracted from the CPU
> + * bus address. This 0x40000000 is also based on io_base from DT.
> + */
> +static u64 visconti_pcie_cpu_addr_fixup(struct dw_pcie *pci, u64 cpu_addr)
> +{
> + struct pcie_port *pp = &pci->pp;
> +
> + return cpu_addr & ~pp->io_base;
> +}
> +
> +static const struct dw_pcie_ops dw_pcie_ops = {
> + .cpu_addr_fixup = visconti_pcie_cpu_addr_fixup,
> + .link_up = visconti_pcie_link_up,
> + .start_link = visconti_pcie_start_link,
> + .stop_link = visconti_pcie_stop_link,
> +};
> +
> +static int visconti_pcie_power_on(struct visconti_pcie *pcie)
> +{
> + void __iomem *addr;
> + int err;
> + u32 val;
> +
> + visconti_smu_writel(pcie,
> + PISMU_CKON_PCIE_AUX_CLK | PISMU_CKON_PCIE_MSTR_ACLK,
> + PISMU_CKON_PCIE);
> + ndelay(250);
> +
> + visconti_smu_writel(pcie, PISMU_RSOFF_PCIE_ULREG_RST_N,
> + PISMU_RSOFF_PCIE);
> + visconti_ulreg_writel(pcie, PCIE_UL_REG_S_PCIE_MODE_RC,
> + PCIE_UL_REG_S_PCIE_MODE);
> +
> + val = PCIE_UL_REG_S_PERSTN_CTRL_INIT;
> + visconti_ulreg_writel(pcie, val, PCIE_UL_REG_S_PERSTN_CTRL);
> + udelay(100);
> +
> + val |= PCIE_UL_PERSTN_OUT;
> + visconti_ulreg_writel(pcie, val, PCIE_UL_REG_S_PERSTN_CTRL);
> + udelay(100);
> +
> + visconti_smu_writel(pcie, PISMU_RSOFF_PCIE_PWR_UP_RST_N,
> + PISMU_RSOFF_PCIE);
> +
> + addr = pcie->ulreg_base + PCIE_UL_REG_S_PHY_INIT_03;
> + err = readl_relaxed_poll_timeout(addr, val,
> + (val & PCIE_UL_PHY0_SRAM_INIT_DONE),
> + 100, 1000);
> + if (err)
> + return err;
> +
> + visconti_ulreg_writel(pcie, PCIE_UL_PHY0_SRAM_EXT_LD_DONE,
> + PCIE_UL_REG_S_PHY_INIT_02);
> +
> + addr = pcie->ulreg_base + PCIE_UL_REG_S_SIG_MON;
> + return readl_relaxed_poll_timeout(addr, val,
> + (val & PCIE_UL_CORE_RST_N_MON), 100,
> + 1000);
> +}
> +
> +static int visconti_pcie_host_init(struct pcie_port *pp)
> +{
> + struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> + struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
> +
> + return visconti_pcie_power_on(pcie);

This function doesn't do anything but call visconti_pcie_power_on().
Just collapse to 1 function.

> +}
> +
> +static const struct dw_pcie_host_ops visconti_pcie_host_ops = {
> + .host_init = visconti_pcie_host_init,
> +};
> +
> +static int visconti_get_resources(struct platform_device *pdev,
> + struct visconti_pcie *pcie)
> +{
> + struct device *dev = &pdev->dev;
> +
> + pcie->ulreg_base = devm_platform_ioremap_resource_byname(pdev, "ulreg");
> + if (IS_ERR(pcie->ulreg_base))
> + return PTR_ERR(pcie->ulreg_base);
> +
> + pcie->smu_base = devm_platform_ioremap_resource_byname(pdev, "smu");
> + if (IS_ERR(pcie->smu_base))
> + return PTR_ERR(pcie->smu_base);
> +
> + pcie->mpu_base = devm_platform_ioremap_resource_byname(pdev, "mpu");
> + if (IS_ERR(pcie->mpu_base))
> + return PTR_ERR(pcie->mpu_base);
> +
> + pcie->refclk = devm_clk_get(dev, "ref");
> + if (IS_ERR(pcie->refclk))
> + return dev_err_probe(dev, PTR_ERR(pcie->refclk),
> + "Failed to get ref clock\n");
> +
> + pcie->coreclk = devm_clk_get(dev, "core");
> + if (IS_ERR(pcie->coreclk))
> + return dev_err_probe(dev, PTR_ERR(pcie->coreclk),
> + "Failed to get core clock\n");
> +
> + pcie->auxclk = devm_clk_get(dev, "aux");
> + if (IS_ERR(pcie->auxclk))
> + return dev_err_probe(dev, PTR_ERR(pcie->auxclk),
> + "Failed to get aux clock\n");
> +
> + return 0;
> +}
> +
> +static int
> +visconti_add_pcie_port(struct visconti_pcie *pcie, struct platform_device *pdev)
> +{
> + struct dw_pcie *pci = &pcie->pci;
> + struct pcie_port *pp = &pci->pp;
> + struct device *dev = &pdev->dev;
> +
> + pp->irq = platform_get_irq_byname(pdev, "intr");
> + if (pp->irq < 0) {
> + dev_err(dev, "Interrupt intr is missing");
> + return pp->irq;
> + }
> +
> + pp->ops = &visconti_pcie_host_ops;
> +
> + pci->link_gen = of_pci_get_max_link_speed(pdev->dev.of_node);

The common DWC code reads this for you now. You only need to set it to
default. See other drivers for examples.

> + if (pci->link_gen < 0 || pci->link_gen > 3) {
> + pci->link_gen = 3;
> + dev_dbg(dev, "Applied default link speed\n");
> + }
> +
> + return dw_pcie_host_init(pp);
> +}
> +
> +static int visconti_pcie_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct visconti_pcie *pcie;
> + struct dw_pcie *pci;
> + int ret;
> +
> + pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
> + if (!pcie)
> + return -ENOMEM;
> +
> + pci = &pcie->pci;
> + pci->dev = dev;
> + pci->ops = &dw_pcie_ops;
> +
> + ret = visconti_get_resources(pdev, pcie);
> + if (ret)
> + return ret;
> +
> + platform_set_drvdata(pdev, pcie);
> +
> + return visconti_add_pcie_port(pcie, pdev);
> +}
> +
> +static const struct of_device_id visconti_pcie_match[] = {
> + { .compatible = "toshiba,visconti-pcie" },
> + {},
> +};
> +
> +static struct platform_driver visconti_pcie_driver = {
> + .probe = visconti_pcie_probe,
> + .driver = {
> + .name = "visconti-pcie",
> + .of_match_table = visconti_pcie_match,
> + .suppress_bind_attrs = true,
> + },
> +};
> +
> +builtin_platform_driver(visconti_pcie_driver);
> --
> 2.32.0
>

Next message: Bjorn Helgaas: "Re: [PATCH 0/4] PCI: replace dublicated MRRS limit quirks"
Previous message: 권오훈: "RE: [PATCH] mm: sparse: pass section_nr to section_mark_present"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]