Re: [v8 2/2] pwm: Add Aspeed ast2600 PWM support

From: Uwe Kleine-König
Date: Fri Jul 02 2021 - 10:32:08 EST

Next message: Greg KH: "Re: [PATCH] dio: return -ENOMEM when kzalloc() fails"
Previous message: Arnd Bergmann: "[PATCH] mips: always link byteswap helpers into decompressor"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hello Billy,

On Tue, Jun 08, 2021 at 02:46:58PM +0800, Billy Tsai wrote:
> This patch add the support of PWM controller which can be found at aspeed
> ast2600 soc. The pwm supoorts up to 16 channels and it's part function
> of multi-function device "pwm-tach controller".
>
> Signed-off-by: Billy Tsai <billy_tsai@xxxxxxxxxxxxxx>
> ---
> drivers/pwm/Kconfig | 9 +
> drivers/pwm/Makefile | 1 +
> drivers/pwm/pwm-aspeed-ast2600.c | 311 +++++++++++++++++++++++++++++++
> 3 files changed, 321 insertions(+)
> create mode 100644 drivers/pwm/pwm-aspeed-ast2600.c
>
> diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
> index 63be5362fd3a..a5aac3ca4ac7 100644
> --- a/drivers/pwm/Kconfig
> +++ b/drivers/pwm/Kconfig
> @@ -51,6 +51,15 @@ config PWM_AB8500
> To compile this driver as a module, choose M here: the module
> will be called pwm-ab8500.
>
> +config PWM_ASPEED_AST2600
> + tristate "Aspeed ast2600 PWM support"
> + depends on ARCH_ASPEED || COMPILE_TEST
> + help
> + This driver provides support for Aspeed ast2600 PWM controllers.
> +
> + To compile this driver as a module, choose M here: the module
> + will be called pwm-aspeed-ast2600.
> +
> config PWM_ATMEL
> tristate "Atmel PWM support"
> depends on OF
> diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
> index cbdcd55d69ee..ada454f9129a 100644
> --- a/drivers/pwm/Makefile
> +++ b/drivers/pwm/Makefile
> @@ -2,6 +2,7 @@
> obj-$(CONFIG_PWM) += core.o
> obj-$(CONFIG_PWM_SYSFS) += sysfs.o
> obj-$(CONFIG_PWM_AB8500) += pwm-ab8500.o
> +obj-$(CONFIG_PWM_ASPEED_AST2600) += pwm-aspeed-ast2600.o
> obj-$(CONFIG_PWM_ATMEL) += pwm-atmel.o
> obj-$(CONFIG_PWM_ATMEL_HLCDC_PWM) += pwm-atmel-hlcdc.o
> obj-$(CONFIG_PWM_ATMEL_TCB) += pwm-atmel-tcb.o
> diff --git a/drivers/pwm/pwm-aspeed-ast2600.c b/drivers/pwm/pwm-aspeed-ast2600.c
> new file mode 100644
> index 000000000000..6ea0f7eb311f
> --- /dev/null
> +++ b/drivers/pwm/pwm-aspeed-ast2600.c
> @@ -0,0 +1,311 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Copyright (C) 2021 Aspeed Technology Inc.
> + *
> + * PWM controller driver for Aspeed ast2600 SoCs.
> + * This drivers doesn't support earlier version of the IP.
> + *
> + * The formula of pwm period duration:
> + * period duration = ((DIV_L + 1) * BIT(DIV_H) * (PERIOD + 1)) / input-clk
> + *
> + * The software driver fixes the period to 255, which causes the high-frequency
> + * precision of the PWM to be coarse, in exchange for the fineness of the duty cycle.
> + *
> + * Register usage:
> + * PIN_ENABLE: When it is unset the pwm controller will always output low to the extern.
> + * Use to determine whether the PWM channel is enabled or disabled
> + * CLK_ENABLE: When it is unset the pwm controller will reset the duty counter to 0 and
> + * output low to the PIN_ENABLE mux after that the driver can still change the pwm period
> + * and duty and the value will apply when CLK_ENABLE be set again.
> + * Use to determine whether duty_cycle bigger than 0.
> + * PWM_ASPEED_CTRL_INVERSE: When it is toggled the output value will inverse immediately.
> + * PWM_ASPEED_DUTY_CYCLE_FALLING_POINT/PWM_ASPEED_DUTY_CYCLE_RISING_POINT: When these two
> + * values are equal it means the duty cycle = 100%.
> + *
> + * Limitations:
> + * - When changing both duty cycle and period, we cannot prevent in
> + * software that the output might produce a period with mixed
> + * settings.
> + * - Disabling the PWM doesn't complete the current period.
> + *
> + * Improvements:
> + * - When only changing one of duty cycle or period, our pwm controller will not
> + * generate the glitch, the configure will change at next cycle of pwm.
> + * This improvement can disable/enable through PWM_ASPEED_CTRL_DUTY_SYNC_DISABLE.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/errno.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_platform.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/sysfs.h>
> +#include <linux/reset.h>
> +#include <linux/regmap.h>
> +#include <linux/bitfield.h>
> +#include <linux/slab.h>
> +#include <linux/pwm.h>
> +#include <linux/math64.h>
> +
> +/* The channel number of Aspeed pwm controller */
> +#define PWM_ASPEED_NR_PWMS 16
> +
> +/* PWM Control Register */
> +#define PWM_ASPEED_CTRL(ch) ((ch) * 0x10 + 0x00)
> +#define PWM_ASPEED_CTRL_LOAD_SEL_RISING_AS_WDT BIT(19)
> +#define PWM_ASPEED_CTRL_DUTY_LOAD_AS_WDT_ENABLE BIT(18)
> +#define PWM_ASPEED_CTRL_DUTY_SYNC_DISABLE BIT(17)
> +#define PWM_ASPEED_CTRL_CLK_ENABLE BIT(16)
> +#define PWM_ASPEED_CTRL_LEVEL_OUTPUT BIT(15)
> +#define PWM_ASPEED_CTRL_INVERSE BIT(14)
> +#define PWM_ASPEED_CTRL_OPEN_DRAIN_ENABLE BIT(13)
> +#define PWM_ASPEED_CTRL_PIN_ENABLE BIT(12)
> +#define PWM_ASPEED_CTRL_CLK_DIV_H GENMASK(11, 8)
> +#define PWM_ASPEED_CTRL_CLK_DIV_L GENMASK(7, 0)
> +
> +/* PWM Duty Cycle Register */
> +#define PWM_ASPEED_DUTY_CYCLE(ch) ((ch) * 0x10 + 0x04)
> +#define PWM_ASPEED_DUTY_CYCLE_PERIOD GENMASK(31, 24)
> +#define PWM_ASPEED_DUTY_CYCLE_POINT_AS_WDT GENMASK(23, 16)
> +#define PWM_ASPEED_DUTY_CYCLE_FALLING_POINT GENMASK(15, 8)
> +#define PWM_ASPEED_DUTY_CYCLE_RISING_POINT GENMASK(7, 0)
> +
> +/* PWM fixed value */
> +#define PWM_ASPEED_FIXED_PERIOD FIELD_MAX(PWM_ASPEED_DUTY_CYCLE_PERIOD)
> +
> +struct aspeed_pwm_data {
> + struct pwm_chip chip;
> + struct clk *clk;
> + struct regmap *regmap;
> + struct reset_control *reset;
> +};
> +
> +static inline struct aspeed_pwm_data *
> +aspeed_pwm_chip_to_data(struct pwm_chip *chip)
> +{
> + return container_of(chip, struct aspeed_pwm_data, chip);
> +}
> +
> +static void aspeed_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
> + struct pwm_state *state)
> +{
> + struct device *dev = chip->dev;
> + struct aspeed_pwm_data *priv = aspeed_pwm_chip_to_data(chip);
> + u32 index = pwm->hwpwm;
> + bool polarity, ch_en, clk_en;
> + u32 duty_pt, val;
> + unsigned long rate;
> + u64 div_h, div_l, clk_period;
> +
> + regmap_read(priv->regmap, PWM_ASPEED_CTRL(index), &val);
> + polarity = FIELD_GET(PWM_ASPEED_CTRL_INVERSE, val);
> + ch_en = FIELD_GET(PWM_ASPEED_CTRL_PIN_ENABLE, val);
> + clk_en = FIELD_GET(PWM_ASPEED_CTRL_CLK_ENABLE, val);
> + div_h = FIELD_GET(PWM_ASPEED_CTRL_CLK_DIV_H, val);
> + div_l = FIELD_GET(PWM_ASPEED_CTRL_CLK_DIV_L, val);
> + regmap_read(priv->regmap, PWM_ASPEED_DUTY_CYCLE(index), &val);
> + duty_pt = FIELD_GET(PWM_ASPEED_DUTY_CYCLE_FALLING_POINT, val);
> + clk_period = FIELD_GET(PWM_ASPEED_DUTY_CYCLE_PERIOD, val);
> +
> + rate = clk_get_rate(priv->clk);
> + state->period = DIV_ROUND_UP_ULL((u64)NSEC_PER_SEC * _BITULL(div_h) *
> + (div_l + 1) * (clk_period + 1),
> + rate);

Instead of _BITULL(div_h) you can just do << div_h, which reads a bit
easier.

The multiplication can be up to:

100000000 * (1 << 31) * (31 + 1) * (255 + 1)

right? This needs 71 bits and so might overflow a u64.

I guess to prevent that you have to do something like SH_DIV does for a
u32 division:

u64 rem;

/*
* To calculate
*
* roundup(NSEC_PER_SEC * (div_l + 1) * (clk_period + 1) << div_h / rate)
*
* we have to jump through some hoops because the numerator
* might not fit into a u64. So calculate:
*
* roundup(NSEC_PER_SEC * (div_l + 1) * (clk_period + 1) / rate) << div_h
*
* and fixup for the imprecision.
*/
nom = (u64)NSEC_PER_SEC * (div_l + 1) * (clk_period + 1) + (rate - 1);
rem = do_div(nom, rate);
state->period = nom << div_h + DIV_ROUND_DOWN_ULL(rem << div_h + (rate >> 1), rate);

You might want to double check my math here, I didn't invest the time to
verify myself that this is sensible but just quickly combined SH_DIV and
DIV_ROUND_UP_ULL.

> + if (clk_en && duty_pt)
> + state->duty_cycle = DIV_ROUND_UP_ULL(
> + state->period * duty_pt, clk_period + 1);

You're loosing precision here. You have to repeat the hoop jumping from
above to fix.

> + else
> + state->duty_cycle = clk_en ? state->period : 0;
> + state->polarity = polarity;
> + state->enabled = ch_en;
> + dev_dbg(dev, "get period: %lldns, duty_cycle: %lldns", state->period,
> + state->duty_cycle);
> +}
> +
> +static int aspeed_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
> + const struct pwm_state *state)
> +{
> + struct device *dev = chip->dev;
> + struct aspeed_pwm_data *priv = aspeed_pwm_chip_to_data(chip);
> + u32 index = pwm->hwpwm, duty_pt;
> + unsigned long rate;
> + u64 div_h, div_l, divisor;
> + bool clk_en;
> +
> + dev_dbg(dev, "expect period: %lldns, duty_cycle: %lldns", state->period,
> + state->duty_cycle);
> +
> + rate = clk_get_rate(priv->clk);
> + /*
> + * Pick the smallest value for div_h so that div_l can be the biggest
> + * which results in a finer resolution near the target period value.
> + */
> + divisor = (u64)NSEC_PER_SEC * (PWM_ASPEED_FIXED_PERIOD + 1) *
> + (FIELD_MAX(PWM_ASPEED_CTRL_CLK_DIV_L) + 1);
> + div_h = order_base_2(DIV64_U64_ROUND_UP(rate * state->period, divisor));
> + if (div_h > 0xf)
> + div_h = 0xf;
> +
> + divisor = ((u64)NSEC_PER_SEC * (PWM_ASPEED_FIXED_PERIOD + 1)) << div_h;
> + div_l = div64_u64(rate * state->period, divisor);
> +
> + if (div_l == 0)
> + return -ERANGE;
> +
> + div_l -= 1;
> +
> + if (div_l > 255)
> + div_l = 255;

I already checked that in the previous round, I assume that's fine now.

Best regards
Uwe

--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | https://www.pengutronix.de/ |

Attachment: signature.asc
Description: PGP signature

Next message: Greg KH: "Re: [PATCH] dio: return -ENOMEM when kzalloc() fails"
Previous message: Arnd Bergmann: "[PATCH] mips: always link byteswap helpers into decompressor"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]