[PATCH 01/10] ASoC: codecs: add SoundWire mockup device support
From: Bard Liao
Date: Tue Jul 13 2021 - 23:22:27 EST
From: Pierre-Louis Bossart <pierre-louis.bossart@xxxxxxxxxxxxxxx>
To test the host controller and bus management code, it is currently
required to have a physical SoundWire peripheral attached to the
bus. To help with pre-silicon or early hardware enablement, it would
be very useful to have a SoundWire 'mockup' device that is exposed in
platform firmware but does not drive any signal on the bus.
This is different to the existing ASoC 'dummy' codec uses for I2S/TDM,
the SoundWire spec makes it clear that a device that is not attached
to the bus is not permitted to interact with the bus, be it for
command/control or data.
This patch exposes a 'mockup' device, with a minimalist driver, with 4
partID values reserved by Intel for such test configurations. The
mockup device exposes one full-duplex DAI based on 2 ports (DP1 for
playback and DP8 for capture). The capture data port is just virtual,
such a mockup device is prevented by the SoundWire specification from
presenting any data generated by a Source port without being Attached.
All the callbacks exposed by the SoundWire Slave interface are
populated, even if they just return immediately. This is intentional
to describe what a minimal codec driver should do and implement and
help new codec vendors provide support for their devices.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@xxxxxxxxxxxxxxx>
Reviewed-by: Rander Wang <rander.wang@xxxxxxxxx>
Signed-off-by: Bard Liao <yung-chuan.liao@xxxxxxxxxxxxxxx>
---
sound/soc/codecs/Kconfig | 18 ++
sound/soc/codecs/Makefile | 2 +
sound/soc/codecs/sdw-mockup.c | 310 ++++++++++++++++++++++++++++++++++
3 files changed, 330 insertions(+)
create mode 100644 sound/soc/codecs/sdw-mockup.c
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index 7ebae3f09435..9e3e4db3d75d 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -187,6 +187,7 @@ config SND_SOC_ALL_CODECS
imply SND_SOC_RT715_SDCA_SDW
imply SND_SOC_RT1308_SDW
imply SND_SOC_RT1316_SDW
+ imply SND_SOC_SDW_MOCKUP
imply SND_SOC_SGTL5000
imply SND_SOC_SI476X
imply SND_SOC_SIMPLE_AMPLIFIER
@@ -1287,6 +1288,23 @@ config SND_SOC_RT715_SDCA_SDW
select REGMAP_SOUNDWIRE
select REGMAP_SOUNDWIRE_MBQ
+config SND_SOC_SDW_MOCKUP
+ tristate "SoundWire mockup codec"
+ depends on EXPERT
+ depends on SOUNDWIRE
+ help
+ This option enables a SoundWire mockup codec that does not drive the
+ bus, take part in the command/command protocol or generate data on a
+ Source port.
+ This option is only intended to be used for tests on a device
+ with a connector, in combination with a bus analyzer, or to test new
+ topologies that differ from the actual hardware layout.
+ This mockup device could be totally virtual but could also be a
+ real physical one with one key restriction: it is not allowed by the
+ SoundWire specification to be configured via a sideband mechanism and
+ generate audio data for capture. However, nothing prevents such a
+ peripheral device from snooping the bus.
+
#Freescale sgtl5000 codec
config SND_SOC_SGTL5000
tristate "Freescale SGTL5000 CODEC"
diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile
index de8b83dd2c76..d656b1405473 100644
--- a/sound/soc/codecs/Makefile
+++ b/sound/soc/codecs/Makefile
@@ -203,6 +203,7 @@ snd-soc-rt711-objs := rt711.o rt711-sdw.o
snd-soc-rt711-sdca-objs := rt711-sdca.o rt711-sdca-sdw.o
snd-soc-rt715-objs := rt715.o rt715-sdw.o
snd-soc-rt715-sdca-objs := rt715-sdca.o rt715-sdca-sdw.o
+snd-soc-sdw-mockup-objs := sdw-mockup.o
snd-soc-sgtl5000-objs := sgtl5000.o
snd-soc-alc5623-objs := alc5623.o
snd-soc-alc5632-objs := alc5632.o
@@ -530,6 +531,7 @@ obj-$(CONFIG_SND_SOC_RT711) += snd-soc-rt711.o
obj-$(CONFIG_SND_SOC_RT711_SDCA_SDW) += snd-soc-rt711-sdca.o
obj-$(CONFIG_SND_SOC_RT715) += snd-soc-rt715.o
obj-$(CONFIG_SND_SOC_RT715_SDCA_SDW) += snd-soc-rt715-sdca.o
+obj-$(CONFIG_SND_SOC_SDW_MOCKUP) += snd-soc-sdw-mockup.o
obj-$(CONFIG_SND_SOC_SGTL5000) += snd-soc-sgtl5000.o
obj-$(CONFIG_SND_SOC_SIGMADSP) += snd-soc-sigmadsp.o
obj-$(CONFIG_SND_SOC_SIGMADSP_I2C) += snd-soc-sigmadsp-i2c.o
diff --git a/sound/soc/codecs/sdw-mockup.c b/sound/soc/codecs/sdw-mockup.c
new file mode 100644
index 000000000000..a4f79eb2c69d
--- /dev/null
+++ b/sound/soc/codecs/sdw-mockup.c
@@ -0,0 +1,310 @@
+// SPDX-License-Identifier: GPL-2.0-only
+//
+// sdw-mockup.c -- a mockup SoundWire codec for tests where only the host
+// drives the bus.
+//
+// Copyright(c) 2021 Intel Corporation
+//
+//
+
+#include <linux/device.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/soundwire/sdw.h>
+#include <linux/soundwire/sdw_type.h>
+#include <linux/soundwire/sdw_registers.h>
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+
+struct sdw_mockup_priv {
+ struct sdw_slave *slave;
+};
+
+struct sdw_stream_data {
+ struct sdw_stream_runtime *sdw_stream;
+};
+
+static int sdw_mockup_component_probe(struct snd_soc_component *component)
+{
+ return 0;
+}
+
+static void sdw_mockup_component_remove(struct snd_soc_component *component)
+{
+}
+
+static const struct snd_soc_component_driver snd_soc_sdw_mockup_component = {
+ .probe = sdw_mockup_component_probe,
+ .remove = sdw_mockup_component_remove,
+};
+
+static int sdw_mockup_set_sdw_stream(struct snd_soc_dai *dai, void *sdw_stream,
+ int direction)
+{
+ struct sdw_stream_data *stream;
+
+ if (!sdw_stream)
+ return 0;
+
+ stream = kzalloc(sizeof(*stream), GFP_KERNEL);
+ if (!stream)
+ return -ENOMEM;
+
+ stream->sdw_stream = sdw_stream;
+
+ /* Use tx_mask or rx_mask to configure stream tag and set dma_data */
+ if (direction == SNDRV_PCM_STREAM_PLAYBACK)
+ dai->playback_dma_data = stream;
+ else
+ dai->capture_dma_data = stream;
+
+ return 0;
+}
+
+static void sdw_mockup_shutdown(struct snd_pcm_substream *substream,
+ struct snd_soc_dai *dai)
+{
+ struct sdw_stream_data *stream;
+
+ stream = snd_soc_dai_get_dma_data(dai, substream);
+ snd_soc_dai_set_dma_data(dai, substream, NULL);
+ kfree(stream);
+}
+
+static int sdw_mockup_pcm_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params,
+ struct snd_soc_dai *dai)
+{
+ struct snd_soc_component *component = dai->component;
+ struct sdw_mockup_priv *sdw_mockup = snd_soc_component_get_drvdata(component);
+ struct sdw_stream_config stream_config;
+ struct sdw_port_config port_config;
+ enum sdw_data_direction direction;
+ struct sdw_stream_data *stream;
+ int num_channels;
+ int port;
+ int ret;
+
+ stream = snd_soc_dai_get_dma_data(dai, substream);
+ if (!stream)
+ return -EINVAL;
+
+ if (!sdw_mockup->slave)
+ return -EINVAL;
+
+ /* SoundWire specific configuration */
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
+ direction = SDW_DATA_DIR_RX;
+ port = 1;
+ } else {
+ direction = SDW_DATA_DIR_TX;
+ port = 8;
+ }
+
+ stream_config.frame_rate = params_rate(params);
+ stream_config.ch_count = params_channels(params);
+ stream_config.bps = snd_pcm_format_width(params_format(params));
+ stream_config.direction = direction;
+
+ num_channels = params_channels(params);
+ port_config.ch_mask = (1 << num_channels) - 1;
+ port_config.num = port;
+
+ ret = sdw_stream_add_slave(sdw_mockup->slave, &stream_config,
+ &port_config, 1, stream->sdw_stream);
+ if (ret)
+ dev_err(dai->dev, "Unable to configure port\n");
+
+ return ret;
+}
+
+static int sdw_mockup_pcm_hw_free(struct snd_pcm_substream *substream,
+ struct snd_soc_dai *dai)
+{
+ struct snd_soc_component *component = dai->component;
+ struct sdw_mockup_priv *sdw_mockup = snd_soc_component_get_drvdata(component);
+ struct sdw_stream_data *stream =
+ snd_soc_dai_get_dma_data(dai, substream);
+
+ if (!sdw_mockup->slave)
+ return -EINVAL;
+
+ sdw_stream_remove_slave(sdw_mockup->slave, stream->sdw_stream);
+ return 0;
+}
+
+static const struct snd_soc_dai_ops sdw_mockup_ops = {
+ .hw_params = sdw_mockup_pcm_hw_params,
+ .hw_free = sdw_mockup_pcm_hw_free,
+ .set_sdw_stream = sdw_mockup_set_sdw_stream,
+ .shutdown = sdw_mockup_shutdown,
+};
+
+static struct snd_soc_dai_driver sdw_mockup_dai[] = {
+ {
+ .name = "sdw-mockup-aif1",
+ .id = 1,
+ .playback = {
+ .stream_name = "DP1 Playback",
+ .channels_min = 1,
+ .channels_max = 2,
+ },
+ .capture = {
+ .stream_name = "DP8 Capture",
+ .channels_min = 1,
+ .channels_max = 2,
+ },
+ .ops = &sdw_mockup_ops,
+ },
+};
+
+static int sdw_mockup_update_status(struct sdw_slave *slave,
+ enum sdw_slave_status status)
+{
+ return 0;
+}
+
+static int sdw_mockup_read_prop(struct sdw_slave *slave)
+{
+ struct sdw_slave_prop *prop = &slave->prop;
+ int nval;
+ int i, j;
+ u32 bit;
+ unsigned long addr;
+ struct sdw_dpn_prop *dpn;
+
+ prop->paging_support = false;
+
+ /*
+ * first we need to allocate memory for set bits in port lists
+ * the port allocation is completely arbitrary:
+ * DP0 is not supported
+ * DP1 is sink
+ * DP8 is source
+ */
+ prop->source_ports = BIT(8);
+ prop->sink_ports = BIT(1);
+
+ nval = hweight32(prop->source_ports);
+ prop->src_dpn_prop = devm_kcalloc(&slave->dev, nval,
+ sizeof(*prop->src_dpn_prop),
+ GFP_KERNEL);
+ if (!prop->src_dpn_prop)
+ return -ENOMEM;
+
+ i = 0;
+ dpn = prop->src_dpn_prop;
+ addr = prop->source_ports;
+ for_each_set_bit(bit, &addr, 32) {
+ dpn[i].num = bit;
+ dpn[i].type = SDW_DPN_FULL;
+ dpn[i].simple_ch_prep_sm = true;
+ i++;
+ }
+
+ /* do this again for sink now */
+ nval = hweight32(prop->sink_ports);
+ prop->sink_dpn_prop = devm_kcalloc(&slave->dev, nval,
+ sizeof(*prop->sink_dpn_prop),
+ GFP_KERNEL);
+ if (!prop->sink_dpn_prop)
+ return -ENOMEM;
+
+ j = 0;
+ dpn = prop->sink_dpn_prop;
+ addr = prop->sink_ports;
+ for_each_set_bit(bit, &addr, 32) {
+ dpn[j].num = bit;
+ dpn[j].type = SDW_DPN_FULL;
+ dpn[j].simple_ch_prep_sm = true;
+ j++;
+ }
+
+ prop->simple_clk_stop_capable = true;
+
+ /* wake-up event */
+ prop->wake_capable = 0;
+
+ return 0;
+}
+
+static int sdw_mockup_bus_config(struct sdw_slave *slave,
+ struct sdw_bus_params *params)
+{
+ return 0;
+}
+
+static int sdw_mockup_interrupt_callback(struct sdw_slave *slave,
+ struct sdw_slave_intr_status *status)
+{
+ return 0;
+}
+
+static const struct sdw_slave_ops sdw_mockup_slave_ops = {
+ .read_prop = sdw_mockup_read_prop,
+ .interrupt_callback = sdw_mockup_interrupt_callback,
+ .update_status = sdw_mockup_update_status,
+ .bus_config = sdw_mockup_bus_config,
+};
+
+static int sdw_mockup_sdw_probe(struct sdw_slave *slave,
+ const struct sdw_device_id *id)
+{
+ struct device *dev = &slave->dev;
+ struct sdw_mockup_priv *sdw_mockup;
+ int ret;
+
+ sdw_mockup = devm_kzalloc(dev, sizeof(*sdw_mockup), GFP_KERNEL);
+ if (!sdw_mockup)
+ return -ENOMEM;
+
+ dev_set_drvdata(dev, sdw_mockup);
+ sdw_mockup->slave = slave;
+
+ ret = devm_snd_soc_register_component(dev,
+ &snd_soc_sdw_mockup_component,
+ sdw_mockup_dai,
+ ARRAY_SIZE(sdw_mockup_dai));
+
+ return ret;
+}
+
+static int sdw_mockup_sdw_remove(struct sdw_slave *slave)
+{
+ return 0;
+}
+
+/*
+ * Intel reserved parts ID with the following mapping expected:
+ * 0xAAAA: generic full-duplex codec
+ * 0xAA55: headset codec (mock-up of RT711/RT5682) - full-duplex
+ * 0x55AA: amplifier (mock-up of RT1308/Maxim 98373) - playback only with
+ * IV feedback
+ * 0x5555: mic codec (mock-up of RT715) - capture-only
+ */
+static const struct sdw_device_id sdw_mockup_id[] = {
+ SDW_SLAVE_ENTRY_EXT(0x0105, 0xAAAA, 0x0, 0, 0),
+ SDW_SLAVE_ENTRY_EXT(0x0105, 0xAA55, 0x0, 0, 0),
+ SDW_SLAVE_ENTRY_EXT(0x0105, 0x55AA, 0x0, 0, 0),
+ SDW_SLAVE_ENTRY_EXT(0x0105, 0x5555, 0x0, 0, 0),
+ {},
+};
+MODULE_DEVICE_TABLE(sdw, sdw_mockup_id);
+
+static struct sdw_driver sdw_mockup_sdw_driver = {
+ .driver = {
+ .name = "sdw-mockup",
+ .owner = THIS_MODULE,
+ },
+ .probe = sdw_mockup_sdw_probe,
+ .remove = sdw_mockup_sdw_remove,
+ .ops = &sdw_mockup_slave_ops,
+ .id_table = sdw_mockup_id,
+};
+module_sdw_driver(sdw_mockup_sdw_driver);
+
+MODULE_DESCRIPTION("ASoC SDW mockup codec driver");
+MODULE_AUTHOR("Pierre-Louis Bossart <pierre-louis.bossart@xxxxxxxxxxxxxxx>");
+MODULE_LICENSE("GPL");
--
2.17.1