Re: [PATCH 07/14] peci: Add peci-aspeed controller driver

From: Zev Weiss
Date: Tue Jul 27 2021 - 04:49:49 EST


On Mon, Jul 12, 2021 at 05:04:40PM CDT, Iwona Winiarska wrote:
>From: Jae Hyun Yoo <jae.hyun.yoo@xxxxxxxxxxxxxxx>
>
>ASPEED AST24xx/AST25xx/AST26xx SoCs supports the PECI electrical
>interface (a.k.a PECI wire).
>
>Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@xxxxxxxxxxxxxxx>
>Co-developed-by: Iwona Winiarska <iwona.winiarska@xxxxxxxxx>
>Signed-off-by: Iwona Winiarska <iwona.winiarska@xxxxxxxxx>
>Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@xxxxxxxxxxxxxxx>
>---
> MAINTAINERS | 9 +
> drivers/peci/Kconfig | 6 +
> drivers/peci/Makefile | 3 +
> drivers/peci/controller/Kconfig | 12 +
> drivers/peci/controller/Makefile | 3 +
> drivers/peci/controller/peci-aspeed.c | 501 ++++++++++++++++++++++++++
> 6 files changed, 534 insertions(+)
> create mode 100644 drivers/peci/controller/Kconfig
> create mode 100644 drivers/peci/controller/Makefile
> create mode 100644 drivers/peci/controller/peci-aspeed.c
>
>diff --git a/MAINTAINERS b/MAINTAINERS
>index 47411e2b6336..4ba874afa2fa 100644
>--- a/MAINTAINERS
>+++ b/MAINTAINERS
>@@ -2865,6 +2865,15 @@ S: Maintained
> F: Documentation/hwmon/asc7621.rst
> F: drivers/hwmon/asc7621.c
>
>+ASPEED PECI CONTROLLER
>+M: Iwona Winiarska <iwona.winiarska@xxxxxxxxx>
>+M: Jae Hyun Yoo <jae.hyun.yoo@xxxxxxxxxxxxxxx>
>+L: linux-aspeed@xxxxxxxxxxxxxxxx (moderated for non-subscribers)
>+L: openbmc@xxxxxxxxxxxxxxxx (moderated for non-subscribers)
>+S: Supported
>+F: Documentation/devicetree/bindings/peci/peci-aspeed.yaml
>+F: drivers/peci/controller/peci-aspeed.c
>+
> ASPEED PINCTRL DRIVERS
> M: Andrew Jeffery <andrew@xxxxxxxx>
> L: linux-aspeed@xxxxxxxxxxxxxxxx (moderated for non-subscribers)
>diff --git a/drivers/peci/Kconfig b/drivers/peci/Kconfig
>index 601cc3c3c852..0d0ee8009713 100644
>--- a/drivers/peci/Kconfig
>+++ b/drivers/peci/Kconfig
>@@ -12,3 +12,9 @@ menuconfig PECI
>
> This support is also available as a module. If so, the module
> will be called peci.
>+
>+if PECI
>+
>+source "drivers/peci/controller/Kconfig"
>+
>+endif # PECI
>diff --git a/drivers/peci/Makefile b/drivers/peci/Makefile
>index 2bb2f51bcda7..621a993e306a 100644
>--- a/drivers/peci/Makefile
>+++ b/drivers/peci/Makefile
>@@ -3,3 +3,6 @@
> # Core functionality
> peci-y := core.o sysfs.o
> obj-$(CONFIG_PECI) += peci.o
>+
>+# Hardware specific bus drivers
>+obj-y += controller/
>diff --git a/drivers/peci/controller/Kconfig b/drivers/peci/controller/Kconfig
>new file mode 100644
>index 000000000000..8ddbe494677f
>--- /dev/null
>+++ b/drivers/peci/controller/Kconfig
>@@ -0,0 +1,12 @@
>+# SPDX-License-Identifier: GPL-2.0-only
>+
>+config PECI_ASPEED
>+ tristate "ASPEED PECI support"
>+ depends on ARCH_ASPEED || COMPILE_TEST
>+ depends on OF
>+ depends on HAS_IOMEM
>+ help
>+ Enable this driver if you want to support ASPEED PECI controller.
>+
>+ This driver can be also build as a module. If so, the module
>+ will be called peci-aspeed.
>diff --git a/drivers/peci/controller/Makefile b/drivers/peci/controller/Makefile
>new file mode 100644
>index 000000000000..022c28ef1bf0
>--- /dev/null
>+++ b/drivers/peci/controller/Makefile
>@@ -0,0 +1,3 @@
>+# SPDX-License-Identifier: GPL-2.0-only
>+
>+obj-$(CONFIG_PECI_ASPEED) += peci-aspeed.o
>diff --git a/drivers/peci/controller/peci-aspeed.c b/drivers/peci/controller/peci-aspeed.c
>new file mode 100644
>index 000000000000..888b46383ea4
>--- /dev/null
>+++ b/drivers/peci/controller/peci-aspeed.c
>@@ -0,0 +1,501 @@
>+// SPDX-License-Identifier: GPL-2.0-only
>+// Copyright (C) 2012-2017 ASPEED Technology Inc.
>+// Copyright (c) 2018-2021 Intel Corporation
>+
>+#include <linux/bitfield.h>
>+#include <linux/clk.h>
>+#include <linux/delay.h>
>+#include <linux/interrupt.h>
>+#include <linux/io.h>
>+#include <linux/iopoll.h>
>+#include <linux/jiffies.h>
>+#include <linux/module.h>
>+#include <linux/of.h>
>+#include <linux/peci.h>
>+#include <linux/platform_device.h>
>+#include <linux/reset.h>
>+
>+#include <asm/unaligned.h>
>+
>+/* ASPEED PECI Registers */
>+/* Control Register */
>+#define ASPEED_PECI_CTRL 0x00
>+#define ASPEED_PECI_CTRL_SAMPLING_MASK GENMASK(19, 16)
>+#define ASPEED_PECI_CTRL_READ_MODE_MASK GENMASK(13, 12)
>+#define ASPEED_PECI_CTRL_READ_MODE_COUNT BIT(12)
>+#define ASPEED_PECI_CTRL_READ_MODE_DBG BIT(13)

Nitpick: might be nice to keep things in a consistent descending order
here (13 then 12).

>+#define ASPEED_PECI_CTRL_CLK_SOURCE_MASK BIT(11)

_MASK suffix seems out of place on this one.

>+#define ASPEED_PECI_CTRL_CLK_DIV_MASK GENMASK(10, 8)
>+#define ASPEED_PECI_CTRL_INVERT_OUT BIT(7)
>+#define ASPEED_PECI_CTRL_INVERT_IN BIT(6)
>+#define ASPEED_PECI_CTRL_BUS_CONTENT_EN BIT(5)

It *is* already kind of a long macro name, but abbreviating "contention"
to "content" seems a bit confusing; I'd suggest keeping the extra three
characters (or maybe drop the _EN suffix if you want to avoid making it
even longer).

>+#define ASPEED_PECI_CTRL_PECI_EN BIT(4)
>+#define ASPEED_PECI_CTRL_PECI_CLK_EN BIT(0)
>+
>+/* Timing Negotiation Register */
>+#define ASPEED_PECI_TIMING_NEGOTIATION 0x04
>+#define ASPEED_PECI_TIMING_MESSAGE_MASK GENMASK(15, 8)
>+#define ASPEED_PECI_TIMING_ADDRESS_MASK GENMASK(7, 0)
>+
>+/* Command Register */
>+#define ASPEED_PECI_CMD 0x08
>+#define ASPEED_PECI_CMD_PIN_MON BIT(31)
>+#define ASPEED_PECI_CMD_STS_MASK GENMASK(27, 24)
>+#define ASPEED_PECI_CMD_STS_ADDR_T_NEGO 0x3
>+#define ASPEED_PECI_CMD_IDLE_MASK \
>+ (ASPEED_PECI_CMD_STS_MASK | ASPEED_PECI_CMD_PIN_MON)
>+#define ASPEED_PECI_CMD_FIRE BIT(0)
>+
>+/* Read/Write Length Register */
>+#define ASPEED_PECI_RW_LENGTH 0x0c
>+#define ASPEED_PECI_AW_FCS_EN BIT(31)
>+#define ASPEED_PECI_READ_LEN_MASK GENMASK(23, 16)
>+#define ASPEED_PECI_WRITE_LEN_MASK GENMASK(15, 8)
>+#define ASPEED_PECI_TAGET_ADDR_MASK GENMASK(7, 0)

s/TAGET/TARGET/

>+
>+/* Expected FCS Data Register */
>+#define ASPEED_PECI_EXP_FCS 0x10
>+#define ASPEED_PECI_EXP_READ_FCS_MASK GENMASK(23, 16)
>+#define ASPEED_PECI_EXP_AW_FCS_AUTO_MASK GENMASK(15, 8)
>+#define ASPEED_PECI_EXP_WRITE_FCS_MASK GENMASK(7, 0)
>+
>+/* Captured FCS Data Register */
>+#define ASPEED_PECI_CAP_FCS 0x14
>+#define ASPEED_PECI_CAP_READ_FCS_MASK GENMASK(23, 16)
>+#define ASPEED_PECI_CAP_WRITE_FCS_MASK GENMASK(7, 0)
>+
>+/* Interrupt Register */
>+#define ASPEED_PECI_INT_CTRL 0x18
>+#define ASPEED_PECI_TIMING_NEGO_SEL_MASK GENMASK(31, 30)
>+#define ASPEED_PECI_1ST_BIT_OF_ADDR_NEGO 0
>+#define ASPEED_PECI_2ND_BIT_OF_ADDR_NEGO 1
>+#define ASPEED_PECI_MESSAGE_NEGO 2
>+#define ASPEED_PECI_INT_MASK GENMASK(4, 0)
>+#define ASPEED_PECI_INT_BUS_TIMEOUT BIT(4)
>+#define ASPEED_PECI_INT_BUS_CONNECT BIT(3)

s/CONNECT/CONTENTION/

>+#define ASPEED_PECI_INT_W_FCS_BAD BIT(2)
>+#define ASPEED_PECI_INT_W_FCS_ABORT BIT(1)
>+#define ASPEED_PECI_INT_CMD_DONE BIT(0)
>+
>+/* Interrupt Status Register */
>+#define ASPEED_PECI_INT_STS 0x1c
>+#define ASPEED_PECI_INT_TIMING_RESULT_MASK GENMASK(29, 16)
>+ /* bits[4..0]: Same bit fields in the 'Interrupt Register' */
>+
>+/* Rx/Tx Data Buffer Registers */
>+#define ASPEED_PECI_W_DATA0 0x20
>+#define ASPEED_PECI_W_DATA1 0x24
>+#define ASPEED_PECI_W_DATA2 0x28
>+#define ASPEED_PECI_W_DATA3 0x2c
>+#define ASPEED_PECI_R_DATA0 0x30
>+#define ASPEED_PECI_R_DATA1 0x34
>+#define ASPEED_PECI_R_DATA2 0x38
>+#define ASPEED_PECI_R_DATA3 0x3c
>+#define ASPEED_PECI_W_DATA4 0x40
>+#define ASPEED_PECI_W_DATA5 0x44
>+#define ASPEED_PECI_W_DATA6 0x48
>+#define ASPEED_PECI_W_DATA7 0x4c
>+#define ASPEED_PECI_R_DATA4 0x50
>+#define ASPEED_PECI_R_DATA5 0x54
>+#define ASPEED_PECI_R_DATA6 0x58
>+#define ASPEED_PECI_R_DATA7 0x5c
>+#define ASPEED_PECI_DATA_BUF_SIZE_MAX 32
>+
>+/* Timing Negotiation */
>+#define ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT 8
>+#define ASPEED_PECI_RD_SAMPLING_POINT_MAX (BIT(4) - 1)
>+#define ASPEED_PECI_CLK_DIV_DEFAULT 0
>+#define ASPEED_PECI_CLK_DIV_MAX (BIT(3) - 1)
>+#define ASPEED_PECI_MSG_TIMING_DEFAULT 1
>+#define ASPEED_PECI_MSG_TIMING_MAX (BIT(8) - 1)
>+#define ASPEED_PECI_ADDR_TIMING_DEFAULT 1
>+#define ASPEED_PECI_ADDR_TIMING_MAX (BIT(8) - 1)
>+
>+/* Timeout */
>+#define ASPEED_PECI_IDLE_CHECK_TIMEOUT_US (50 * USEC_PER_MSEC)
>+#define ASPEED_PECI_IDLE_CHECK_INTERVAL_US (10 * USEC_PER_MSEC)
>+#define ASPEED_PECI_CMD_TIMEOUT_MS_DEFAULT (1000)
>+#define ASPEED_PECI_CMD_TIMEOUT_MS_MAX (1000)
>+
>+struct aspeed_peci {
>+ struct peci_controller controller;
>+ struct device *dev;
>+ void __iomem *base;
>+ struct clk *clk;
>+ struct reset_control *rst;
>+ int irq;
>+ spinlock_t lock; /* to sync completion status handling */
>+ struct completion xfer_complete;
>+ u32 status;
>+ u32 cmd_timeout_ms;
>+ u32 msg_timing;
>+ u32 addr_timing;
>+ u32 rd_sampling_point;
>+ u32 clk_div;
>+};
>+
>+static inline struct aspeed_peci *to_aspeed_peci(struct peci_controller *a)
>+{
>+ return container_of(a, struct aspeed_peci, controller);
>+}
>+
>+static void aspeed_peci_init_regs(struct aspeed_peci *priv)
>+{
>+ u32 val;
>+
>+ val = FIELD_PREP(ASPEED_PECI_CTRL_CLK_DIV_MASK, ASPEED_PECI_CLK_DIV_DEFAULT);
>+ val |= ASPEED_PECI_CTRL_PECI_CLK_EN;
>+ writel(val, priv->base + ASPEED_PECI_CTRL);
>+ /*
>+ * Timing negotiation period setting.
>+ * The unit of the programmed value is 4 times of PECI clock period.
>+ */
>+ val = FIELD_PREP(ASPEED_PECI_TIMING_MESSAGE_MASK, priv->msg_timing);
>+ val |= FIELD_PREP(ASPEED_PECI_TIMING_ADDRESS_MASK, priv->addr_timing);
>+ writel(val, priv->base + ASPEED_PECI_TIMING_NEGOTIATION);
>+
>+ /* Clear interrupts */
>+ val = readl(priv->base + ASPEED_PECI_INT_STS) | ASPEED_PECI_INT_MASK;

This should be & instead of |, I'm guessing?

>+ writel(val, priv->base + ASPEED_PECI_INT_STS);
>+
>+ /* Set timing negotiation mode and enable interrupts */
>+ val = FIELD_PREP(ASPEED_PECI_TIMING_NEGO_SEL_MASK, ASPEED_PECI_1ST_BIT_OF_ADDR_NEGO);
>+ val |= ASPEED_PECI_INT_MASK;
>+ writel(val, priv->base + ASPEED_PECI_INT_CTRL);
>+
>+ val = FIELD_PREP(ASPEED_PECI_CTRL_SAMPLING_MASK, priv->rd_sampling_point);
>+ val |= FIELD_PREP(ASPEED_PECI_CTRL_CLK_DIV_MASK, priv->clk_div);
>+ val |= ASPEED_PECI_CTRL_PECI_EN;
>+ val |= ASPEED_PECI_CTRL_PECI_CLK_EN;
>+ writel(val, priv->base + ASPEED_PECI_CTRL);
>+}
>+
>+static inline int aspeed_peci_check_idle(struct aspeed_peci *priv)
>+{
>+ u32 cmd_sts = readl(priv->base + ASPEED_PECI_CMD);
>+
>+ if (FIELD_GET(ASPEED_PECI_CMD_STS_MASK, cmd_sts) == ASPEED_PECI_CMD_STS_ADDR_T_NEGO)
>+ aspeed_peci_init_regs(priv);
>+
>+ return readl_poll_timeout(priv->base + ASPEED_PECI_CMD,
>+ cmd_sts,
>+ !(cmd_sts & ASPEED_PECI_CMD_IDLE_MASK),
>+ ASPEED_PECI_IDLE_CHECK_INTERVAL_US,
>+ ASPEED_PECI_IDLE_CHECK_TIMEOUT_US);
>+}
>+
>+static int aspeed_peci_xfer(struct peci_controller *controller,
>+ u8 addr, struct peci_request *req)
>+{
>+ struct aspeed_peci *priv = to_aspeed_peci(controller);
>+ unsigned long flags, timeout = msecs_to_jiffies(priv->cmd_timeout_ms);
>+ u32 peci_head;
>+ int ret;
>+
>+ if (req->tx.len > ASPEED_PECI_DATA_BUF_SIZE_MAX ||
>+ req->rx.len > ASPEED_PECI_DATA_BUF_SIZE_MAX)
>+ return -EINVAL;
>+
>+ /* Check command sts and bus idle state */
>+ ret = aspeed_peci_check_idle(priv);
>+ if (ret)
>+ return ret; /* -ETIMEDOUT */
>+
>+ spin_lock_irqsave(&priv->lock, flags);
>+ reinit_completion(&priv->xfer_complete);
>+
>+ peci_head = FIELD_PREP(ASPEED_PECI_TAGET_ADDR_MASK, addr) |
>+ FIELD_PREP(ASPEED_PECI_WRITE_LEN_MASK, req->tx.len) |
>+ FIELD_PREP(ASPEED_PECI_READ_LEN_MASK, req->rx.len);
>+
>+ writel(peci_head, priv->base + ASPEED_PECI_RW_LENGTH);
>+
>+ memcpy_toio(priv->base + ASPEED_PECI_W_DATA0, req->tx.buf,
>+ req->tx.len > 16 ? 16 : req->tx.len);

min(req->tx.len, 16) for the third argument there might be a bit
clearer.

>+ if (req->tx.len > 16)
>+ memcpy_toio(priv->base + ASPEED_PECI_W_DATA4, req->tx.buf + 16,
>+ req->tx.len - 16);
>+
>+ dev_dbg(priv->dev, "HEAD : 0x%08x\n", peci_head);
>+ print_hex_dump_bytes("TX : ", DUMP_PREFIX_NONE, req->tx.buf, req->tx.len);
>+
>+ priv->status = 0;
>+ writel(ASPEED_PECI_CMD_FIRE, priv->base + ASPEED_PECI_CMD);
>+ spin_unlock_irqrestore(&priv->lock, flags);
>+
>+ ret = wait_for_completion_interruptible_timeout(&priv->xfer_complete, timeout);
>+ if (ret < 0)
>+ return ret;
>+
>+ if (ret == 0) {
>+ dev_dbg(priv->dev, "Timeout waiting for a response!\n");
>+ return -ETIMEDOUT;
>+ }
>+
>+ spin_lock_irqsave(&priv->lock, flags);
>+
>+ writel(0, priv->base + ASPEED_PECI_CMD);
>+
>+ if (priv->status != ASPEED_PECI_INT_CMD_DONE) {
>+ spin_unlock_irqrestore(&priv->lock, flags);
>+ dev_dbg(priv->dev, "No valid response!\n");
>+ return -EIO;
>+ }
>+
>+ spin_unlock_irqrestore(&priv->lock, flags);
>+
>+ memcpy_fromio(req->rx.buf, priv->base + ASPEED_PECI_R_DATA0,
>+ req->rx.len > 16 ? 16 : req->rx.len);

Likewise, min(req->rx.len, 16) here.

>+ if (req->rx.len > 16)
>+ memcpy_fromio(req->rx.buf + 16, priv->base + ASPEED_PECI_R_DATA4,
>+ req->rx.len - 16);
>+
>+ print_hex_dump_bytes("RX : ", DUMP_PREFIX_NONE, req->rx.buf, req->rx.len);
>+
>+ return 0;
>+}
>+
>+static irqreturn_t aspeed_peci_irq_handler(int irq, void *arg)
>+{
>+ struct aspeed_peci *priv = arg;
>+ u32 status;
>+
>+ spin_lock(&priv->lock);
>+ status = readl(priv->base + ASPEED_PECI_INT_STS);
>+ writel(status, priv->base + ASPEED_PECI_INT_STS);
>+ priv->status |= (status & ASPEED_PECI_INT_MASK);
>+
>+ /*
>+ * In most cases, interrupt bits will be set one by one but also note
>+ * that multiple interrupt bits could be set at the same time.
>+ */
>+ if (status & ASPEED_PECI_INT_BUS_TIMEOUT)
>+ dev_dbg_ratelimited(priv->dev, "ASPEED_PECI_INT_BUS_TIMEOUT\n");
>+
>+ if (status & ASPEED_PECI_INT_BUS_CONNECT)
>+ dev_dbg_ratelimited(priv->dev, "ASPEED_PECI_INT_BUS_CONNECT\n");

s/CONNECT/CONTENTION/ here too (in the message string).

>+
>+ if (status & ASPEED_PECI_INT_W_FCS_BAD)
>+ dev_dbg_ratelimited(priv->dev, "ASPEED_PECI_INT_W_FCS_BAD\n");
>+
>+ if (status & ASPEED_PECI_INT_W_FCS_ABORT)
>+ dev_dbg_ratelimited(priv->dev, "ASPEED_PECI_INT_W_FCS_ABORT\n");

Bus contention can of course arise legitimately, and I suppose an
offline host CPU might result in a timeout, so dbg seems fine for those
(though as Dan suggests, making some counters available seems like a
good idea, especially for contention). Are the FCS error cases
significant enough to warrant something less likely to go unnoticed
though? (e.g. dev_warn_ratelimited() or something?)

>+
>+ /*
>+ * All commands should be ended up with a ASPEED_PECI_INT_CMD_DONE bit
>+ * set even in an error case.
>+ */
>+ if (status & ASPEED_PECI_INT_CMD_DONE)
>+ complete(&priv->xfer_complete);
>+
>+ spin_unlock(&priv->lock);
>+
>+ return IRQ_HANDLED;
>+}
>+
>+static void __sanitize_clock_divider(struct aspeed_peci *priv)
>+{
>+ u32 clk_div;
>+ int ret;
>+
>+ ret = device_property_read_u32(priv->dev, "clock-divider", &clk_div);
>+ if (ret) {
>+ clk_div = ASPEED_PECI_CLK_DIV_DEFAULT;
>+ } else if (clk_div > ASPEED_PECI_CLK_DIV_MAX) {
>+ dev_warn(priv->dev, "Invalid clock-divider: %u, Using default: %u\n",
>+ clk_div, ASPEED_PECI_CLK_DIV_DEFAULT);
>+
>+ clk_div = ASPEED_PECI_CLK_DIV_DEFAULT;
>+ }
>+
>+ priv->clk_div = clk_div;
>+}
>+

The naming of these __sanitize_*() functions is a bit inconsistent with
the rest of the driver -- though given how similar they all look, could
they instead be refactored into a single helper function taking
property-name, default-value, and max-value parameters?

>+static void __sanitize_msg_timing(struct aspeed_peci *priv)
>+{
>+ u32 msg_timing;
>+ int ret;
>+
>+ ret = device_property_read_u32(priv->dev, "msg-timing", &msg_timing);
>+ if (ret) {
>+ msg_timing = ASPEED_PECI_MSG_TIMING_DEFAULT;
>+ } else if (msg_timing > ASPEED_PECI_MSG_TIMING_MAX) {
>+ dev_warn(priv->dev, "Invalid msg-timing : %u, Use default : %u\n",
>+ msg_timing, ASPEED_PECI_MSG_TIMING_DEFAULT);
>+
>+ msg_timing = ASPEED_PECI_MSG_TIMING_DEFAULT;
>+ }
>+
>+ priv->msg_timing = msg_timing;
>+}
>+
>+static void __sanitize_addr_timing(struct aspeed_peci *priv)
>+{
>+ u32 addr_timing;
>+ int ret;
>+
>+ ret = device_property_read_u32(priv->dev, "addr-timing", &addr_timing);
>+ if (ret) {
>+ addr_timing = ASPEED_PECI_ADDR_TIMING_DEFAULT;
>+ } else if (addr_timing > ASPEED_PECI_ADDR_TIMING_MAX) {
>+ dev_warn(priv->dev, "Invalid addr-timing : %u, Use default : %u\n",
>+ addr_timing, ASPEED_PECI_ADDR_TIMING_DEFAULT);
>+
>+ addr_timing = ASPEED_PECI_ADDR_TIMING_DEFAULT;
>+ }
>+
>+ priv->addr_timing = addr_timing;
>+}
>+
>+static void __sanitize_rd_sampling_point(struct aspeed_peci *priv)
>+{
>+ u32 rd_sampling_point;
>+ int ret;
>+
>+ ret = device_property_read_u32(priv->dev, "rd-sampling-point", &rd_sampling_point);
>+ if (ret) {
>+ rd_sampling_point = ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT;
>+ } else if (rd_sampling_point > ASPEED_PECI_RD_SAMPLING_POINT_MAX) {
>+ dev_warn(priv->dev, "Invalid rd-sampling-point: %u, Use default : %u\n",
>+ rd_sampling_point, ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT);
>+
>+ rd_sampling_point = ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT;
>+ }
>+
>+ priv->rd_sampling_point = rd_sampling_point;
>+}
>+
>+static void __sanitize_cmd_timeout(struct aspeed_peci *priv)
>+{
>+ u32 timeout;
>+ int ret;
>+
>+ ret = device_property_read_u32(priv->dev, "cmd-timeout-ms", &timeout);
>+ if (ret) {
>+ timeout = ASPEED_PECI_CMD_TIMEOUT_MS_DEFAULT;
>+ } else if (timeout > ASPEED_PECI_CMD_TIMEOUT_MS_MAX || timeout == 0) {
>+ dev_warn(priv->dev, "Invalid cmd-timeout-ms: %u, Use default: %u\n",
>+ timeout, ASPEED_PECI_CMD_TIMEOUT_MS_DEFAULT);
>+
>+ timeout = ASPEED_PECI_CMD_TIMEOUT_MS_DEFAULT;
>+ }
>+
>+ priv->cmd_timeout_ms = timeout;
>+}
>+
>+static void aspeed_peci_device_property_sanitize(struct aspeed_peci *priv)
>+{
>+ __sanitize_clock_divider(priv);
>+ __sanitize_msg_timing(priv);
>+ __sanitize_addr_timing(priv);
>+ __sanitize_rd_sampling_point(priv);
>+ __sanitize_cmd_timeout(priv);
>+}
>+
>+static void aspeed_peci_disable_clk(void *data)
>+{
>+ clk_disable_unprepare(data);
>+}
>+
>+static int aspeed_peci_init_ctrl(struct aspeed_peci *priv)
>+{
>+ int ret;
>+
>+ priv->clk = devm_clk_get(priv->dev, NULL);
>+ if (IS_ERR(priv->clk))
>+ return dev_err_probe(priv->dev, PTR_ERR(priv->clk), "Failed to get clk source\n");
>+
>+ ret = clk_prepare_enable(priv->clk);
>+ if (ret) {
>+ dev_err(priv->dev, "Failed to enable clock\n");
>+ return ret;
>+ }
>+
>+ ret = devm_add_action_or_reset(priv->dev, aspeed_peci_disable_clk, priv->clk);
>+ if (ret)
>+ return ret;
>+
>+ aspeed_peci_device_property_sanitize(priv);
>+
>+ aspeed_peci_init_regs(priv);
>+
>+ return 0;
>+}
>+
>+static int aspeed_peci_probe(struct platform_device *pdev)
>+{
>+ struct aspeed_peci *priv;
>+ int ret;
>+
>+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
>+ if (!priv)
>+ return -ENOMEM;
>+
>+ priv->dev = &pdev->dev;
>+ dev_set_drvdata(priv->dev, priv);
>+
>+ priv->base = devm_platform_ioremap_resource(pdev, 0);
>+ if (IS_ERR(priv->base))
>+ return PTR_ERR(priv->base);
>+
>+ priv->irq = platform_get_irq(pdev, 0);
>+ if (!priv->irq)
>+ return priv->irq;
>+
>+ ret = devm_request_irq(&pdev->dev, priv->irq, aspeed_peci_irq_handler,
>+ 0, "peci-aspeed-irq", priv);

Might as well drop the "-irq" suffix here? (Seems a bit redundant, and
a quick glance through /proc/interrupts on the systems I have at hand
doesn't show anything else following that convention.)

>+ if (ret)
>+ return ret;
>+
>+ init_completion(&priv->xfer_complete);
>+ spin_lock_init(&priv->lock);
>+
>+ priv->controller.xfer = aspeed_peci_xfer;
>+
>+ priv->rst = devm_reset_control_get(&pdev->dev, NULL);
>+ if (IS_ERR(priv->rst)) {
>+ dev_err(&pdev->dev, "Missing or invalid reset controller entry\n");
>+ return PTR_ERR(priv->rst);
>+ }
>+ reset_control_deassert(priv->rst);
>+
>+ ret = aspeed_peci_init_ctrl(priv);
>+ if (ret)
>+ return ret;
>+
>+ return peci_controller_add(&priv->controller, priv->dev);
>+}
>+
>+static int aspeed_peci_remove(struct platform_device *pdev)
>+{
>+ struct aspeed_peci *priv = dev_get_drvdata(&pdev->dev);
>+
>+ peci_controller_remove(&priv->controller);
>+ reset_control_assert(priv->rst);
>+
>+ return 0;
>+}
>+
>+static const struct of_device_id aspeed_peci_of_table[] = {
>+ { .compatible = "aspeed,ast2400-peci", },
>+ { .compatible = "aspeed,ast2500-peci", },
>+ { .compatible = "aspeed,ast2600-peci", },
>+ { }
>+};
>+MODULE_DEVICE_TABLE(of, aspeed_peci_of_table);
>+
>+static struct platform_driver aspeed_peci_driver = {
>+ .probe = aspeed_peci_probe,
>+ .remove = aspeed_peci_remove,
>+ .driver = {
>+ .name = "peci-aspeed",
>+ .of_match_table = aspeed_peci_of_table,
>+ },
>+};
>+module_platform_driver(aspeed_peci_driver);
>+
>+MODULE_AUTHOR("Ryan Chen <ryan_chen@xxxxxxxxxxxxxx>");
>+MODULE_AUTHOR("Jae Hyun Yoo <jae.hyun.yoo@xxxxxxxxxxxxxxx>");
>+MODULE_DESCRIPTION("ASPEED PECI driver");
>+MODULE_LICENSE("GPL");
>+MODULE_IMPORT_NS(PECI);
>--
>2.31.1
>