Re: [PATCH v7 2/6] thermal: sy7636a: Add thermal driver for sy7636a

[Alistair Francis]

On Wed, Jul 21, 2021 at 1:02 AM Lee Jones <lee.jones@xxxxxxxxxx> wrote:
>
> On Thu, 08 Jul 2021, Alistair Francis wrote:
>
> > From: Lars Ivar Miljeteig <lars.ivar.miljeteig@xxxxxxxxxxxxx>
> >
> > Add thermal driver to enable kernel based polling
> > and shutdown of device for temperatures out of spec
> >
> > Signed-off-by: Alistair Francis <alistair@xxxxxxxxxxxxx>
> > ---
> >  drivers/thermal/Kconfig           |   7 ++
> >  drivers/thermal/Makefile          |   1 +
> >  drivers/thermal/sy7636a_thermal.c | 107 ++++++++++++++++++++++++++++++
> >  3 files changed, 115 insertions(+)
> >  create mode 100644 drivers/thermal/sy7636a_thermal.c
> >
> > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> > index d7f44deab5b1..7112c63d9021 100644
> > --- a/drivers/thermal/Kconfig
> > +++ b/drivers/thermal/Kconfig
> > @@ -450,6 +450,13 @@ depends on (ARCH_STI || ARCH_STM32) && OF
> >  source "drivers/thermal/st/Kconfig"
> >  endmenu
> >
> > +config SY7636A_THERMAL
> > +     tristate "SY7636A thermal management"
> > +     depends on MFD_SY7636A
> > +     help
> > +       Enable the sy7636a thermal driver, which supports the
> > +       temperature sensor embedded in Silabs SY7636A chip.
> > +
> >  source "drivers/thermal/tegra/Kconfig"
> >
> >  config GENERIC_ADC_THERMAL
> > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> > index 82fc3e616e54..2e1aca8a0a09 100644
> > --- a/drivers/thermal/Makefile
> > +++ b/drivers/thermal/Makefile
> > @@ -51,6 +51,7 @@ obj-$(CONFIG_DA9062_THERMAL)        += da9062-thermal.o
> >  obj-y                                += intel/
> >  obj-$(CONFIG_TI_SOC_THERMAL) += ti-soc-thermal/
> >  obj-y                                += st/
> > +obj-$(CONFIG_SY7636A_THERMAL)        += sy7636a_thermal.o
> >  obj-$(CONFIG_QCOM_TSENS)     += qcom/
> >  obj-y                                += tegra/
> >  obj-$(CONFIG_HISI_THERMAL)     += hisi_thermal.o
> > diff --git a/drivers/thermal/sy7636a_thermal.c b/drivers/thermal/sy7636a_thermal.c
> > new file mode 100644
> > index 000000000000..705a16fb1045
> > --- /dev/null
> > +++ b/drivers/thermal/sy7636a_thermal.c
> > @@ -0,0 +1,107 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +//
> > +// Functions to access SY3686A power management chip temperature
> > +//
> > +// Copyright (C) 2019 reMarkable AS - http://www.remarkable.com/
> > +//
> > +// Authors: Lars Ivar Miljeteig <lars.ivar.miljeteig@xxxxxxxxxxxxxx>
> > +//          Alistair Francis <alistair@xxxxxxxxxxxxx>
> > +
> > +#include <linux/module.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/thermal.h>
> > +
> > +#include <linux/mfd/sy7636a.h>
> > +
> > +struct sy7636a_data {
> > +     struct sy7636a *sy7636a;
> > +     struct thermal_zone_device *thermal_zone_dev;
> > +};
> > +
> > +static int sy7636a_get_temp(void *arg, int *res)
> > +{
> > +     unsigned int reg_val, mode_ctr;
> > +     int ret;
> > +     struct sy7636a_data *data = arg;
> > +     bool isVoltageActive;
> > +
> > +     ret = regmap_read(data->sy7636a->regmap,
> > +                     SY7636A_REG_OPERATION_MODE_CRL, &mode_ctr);
> > +     if (ret)
> > +             return ret;
> > +
> > +     isVoltageActive = mode_ctr & SY7636A_OPERATION_MODE_CRL_ONOFF;
> > +
> > +     if (!isVoltageActive) {
> > +             ret = regmap_write(data->sy7636a->regmap,
> > +                             SY7636A_REG_OPERATION_MODE_CRL,
> > +                             mode_ctr | SY7636A_OPERATION_MODE_CRL_ONOFF);
> > +             if (ret)
> > +                     return ret;
> > +     }
> > +
> > +     ret = regmap_read(data->sy7636a->regmap,
> > +                     SY7636A_REG_TERMISTOR_READOUT, &reg_val);
> > +     if (ret)
> > +             return ret;
> > +
> > +     if (!isVoltageActive) {
> > +             ret = regmap_write(data->sy7636a->regmap,
> > +                             SY7636A_REG_OPERATION_MODE_CRL,
> > +                             mode_ctr);
> > +             if (ret)
> > +                     return ret;
> > +     }
> > +
> > +     *res = *((signed char*)&reg_val);
> > +     *res *= 1000;
> > +
> > +     return ret;
> > +}
> > +
> > +static const struct thermal_zone_of_device_ops ops = {
> > +     .get_temp       = sy7636a_get_temp,
> > +};
> > +
> > +static int sy7636a_thermal_probe(struct platform_device *pdev)
> > +{
> > +     struct sy7636a *sy7636a = dev_get_drvdata(pdev->dev.parent);
> > +     struct sy7636a_data *data;
> > +
> > +     if (!sy7636a)
> > +             return -EPROBE_DEFER;
>
> How is this possible?

I'm not sure, I have removed this.

>
> > +     data = devm_kzalloc(&pdev->dev, sizeof(struct sy7636a_data), GFP_KERNEL);
>
> sizeof(*data)
>
> > +     if (!data)
> > +             return -ENOMEM;
> > +
> > +     platform_set_drvdata(pdev, data);
> > +
> > +     data->sy7636a = sy7636a;
> > +     data->thermal_zone_dev = devm_thermal_zone_of_sensor_register(
> > +                     pdev->dev.parent,
> > +                     0,
> > +                     data,
>
> Why don't you just pass in your initial ddata?

I'm not sure what you mean, which data?

Alistair