[PATCH 24/39] arm64: dts: qcom: sdm660: Make the DTS an overlay on top of 630

From: Konrad Dybcio
Date: Wed Jul 28 2021 - 18:26:45 EST

Next message: Konrad Dybcio: "[PATCH 17/39] arm64: dts: qcom: sdm630: Add ADSP remoteproc configuration"
Previous message: Konrad Dybcio: "[PATCH 15/39] arm64: dts: qcom: sdm630: Add modem/ADSP SMP2P nodes"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

There is SO MUCH common code between these two SoCs that it makes
no sense to keep what is essentially a duplicate of 630.dtsi. Instead,
it's better to just change the things that differ.

Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxx>
---
.../boot/dts/qcom/sdm660-xiaomi-lavender.dts | 2 -
arch/arm64/boot/dts/qcom/sdm660.dtsi | 448 +++++-------------
2 files changed, 117 insertions(+), 333 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts b/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts
index 76533e8b2092..3e677fb7cfea 100644
--- a/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts
+++ b/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts
@@ -37,8 +37,6 @@ ramoops@a0000000 {

&blsp1_uart2 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&uart_console_active>;
};

&tlmm {
diff --git a/arch/arm64/boot/dts/qcom/sdm660.dtsi b/arch/arm64/boot/dts/qcom/sdm660.dtsi
index 4abbdd03d1e7..13467e2c708a 100644
--- a/arch/arm64/boot/dts/qcom/sdm660.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm660.dtsi
@@ -2,371 +2,157 @@
/*
* Copyright (c) 2018, Craig Tatlor.
* Copyright (c) 2020, Alexey Minnekhanov <alexey.min@xxxxxxxxx>
+ * Copyright (c) 2020, AngeloGioacchino Del Regno <kholk11@xxxxxxxxx>
+ * Copyright (c) 2020, Konrad Dybcio <konradybcio@xxxxxxxxx>
+ * Copyright (c) 2020, Martin Botka <martin.botka1@xxxxxxxxx>
*/

-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/qcom,gcc-sdm660.h>
+#include "sdm630.dtsi"

-/ {
- interrupt-parent = <&intc>;
+&adreno_gpu {
+ compatible = "qcom,adreno-512.0", "qcom,adreno";
+ operating-points-v2 = <&gpu_sdm660_opp_table>;

- #address-cells = <2>;
- #size-cells = <2>;
+ gpu_sdm660_opp_table: opp-table {
+ compatible = "operating-points-v2";

- chosen { };
+ /*
+ * 775MHz is only available on the highest speed bin
+ * Though it cannot be used for now due to interconnect
+ * framework not supporting multiple frequencies
+ * at the same opp-level

- clocks {
- xo_board: xo_board {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <19200000>;
- clock-output-names = "xo_board";
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-level = <RPM_SMD_LEVEL_TURBO>;
+ opp-peak-kBps = <5412000>;
+ opp-supported-hw = <0xCHECKME>;
};

- sleep_clk: sleep_clk {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <32764>;
- clock-output-names = "sleep_clk";
- };
- };
-
- cpus {
- #address-cells = <2>;
- #size-cells = <0>;
+ * These OPPs are correct, but we are lacking support for the
+ * GPU regulator. Hence, disable them for now to prevent the
+ * platform from hanging on high graphics loads.

- CPU0: cpu@100 {
- device_type = "cpu";
- compatible = "qcom,kryo260";
- reg = <0x0 0x100>;
- enable-method = "psci";
- capacity-dmips-mhz = <1024>;
- next-level-cache = <&L2_1>;
- L2_1: l2-cache {
- compatible = "cache";
- cache-level = <2>;
- };
- L1_I_100: l1-icache {
- compatible = "cache";
- };
- L1_D_100: l1-dcache {
- compatible = "cache";
- };
+ opp-700000000 {
+ opp-hz = /bits/ 64 <700000000>;
+ opp-level = <RPM_SMD_LEVEL_TURBO>;
+ opp-peak-kBps = <5184000>;
+ opp-supported-hw = <0xFF>;
};

- CPU1: cpu@101 {
- device_type = "cpu";
- compatible = "qcom,kryo260";
- reg = <0x0 0x101>;
- enable-method = "psci";
- capacity-dmips-mhz = <1024>;
- next-level-cache = <&L2_1>;
- L1_I_101: l1-icache {
- compatible = "cache";
- };
- L1_D_101: l1-dcache {
- compatible = "cache";
- };
+ opp-647000000 {
+ opp-hz = /bits/ 64 <647000000>;
+ opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
+ opp-peak-kBps = <4068000>;
+ opp-supported-hw = <0xFF>;
};

- CPU2: cpu@102 {
- device_type = "cpu";
- compatible = "qcom,kryo260";
- reg = <0x0 0x102>;
- enable-method = "psci";
- capacity-dmips-mhz = <1024>;
- next-level-cache = <&L2_1>;
- L1_I_102: l1-icache {
- compatible = "cache";
- };
- L1_D_102: l1-dcache {
- compatible = "cache";
- };
+ opp-588000000 {
+ opp-hz = /bits/ 64 <588000000>;
+ opp-level = <RPM_SMD_LEVEL_NOM>;
+ opp-peak-kBps = <3072000>;
+ opp-supported-hw = <0xFF>;
};

- CPU3: cpu@103 {
- device_type = "cpu";
- compatible = "qcom,kryo260";
- reg = <0x0 0x103>;
- enable-method = "psci";
- capacity-dmips-mhz = <1024>;
- next-level-cache = <&L2_1>;
- L1_I_103: l1-icache {
- compatible = "cache";
- };
- L1_D_103: l1-dcache {
- compatible = "cache";
- };
+ opp-465000000 {
+ opp-hz = /bits/ 64 <465000000>;
+ opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
+ opp-peak-kBps = <2724000>;
+ opp-supported-hw = <0xFF>;
};

- CPU4: cpu@0 {
- device_type = "cpu";
- compatible = "qcom,kryo260";
- reg = <0x0 0x0>;
- enable-method = "psci";
- capacity-dmips-mhz = <640>;
- next-level-cache = <&L2_0>;
- L2_0: l2-cache {
- compatible = "cache";
- cache-level = <2>;
- };
- L1_I_0: l1-icache {
- compatible = "cache";
- };
- L1_D_0: l1-dcache {
- compatible = "cache";
- };
+ opp-370000000 {
+ opp-hz = /bits/ 64 <370000000>;
+ opp-level = <RPM_SMD_LEVEL_SVS>;
+ opp-peak-kBps = <2188000>;
+ opp-supported-hw = <0xFF>;
};
+ */

- CPU5: cpu@1 {
- device_type = "cpu";
- compatible = "qcom,kryo260";
- reg = <0x0 0x1>;
- enable-method = "psci";
- capacity-dmips-mhz = <640>;
- next-level-cache = <&L2_0>;
- L1_I_1: l1-icache {
- compatible = "cache";
- };
- L1_D_1: l1-dcache {
- compatible = "cache";
- };
+ opp-266000000 {
+ opp-hz = /bits/ 64 <266000000>;
+ opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
+ opp-peak-kBps = <1648000>;
+ opp-supported-hw = <0xFF>;
};

- CPU6: cpu@2 {
- device_type = "cpu";
- compatible = "qcom,kryo260";
- reg = <0x0 0x2>;
- enable-method = "psci";
- capacity-dmips-mhz = <640>;
- next-level-cache = <&L2_0>;
- L1_I_2: l1-icache {
- compatible = "cache";
- };
- L1_D_2: l1-dcache {
- compatible = "cache";
- };
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
+ opp-peak-kBps = <1200000>;
+ opp-supported-hw = <0xFF>;
};
-
- CPU7: cpu@3 {
- device_type = "cpu";
- compatible = "qcom,kryo260";
- reg = <0x0 0x3>;
- enable-method = "psci";
- capacity-dmips-mhz = <640>;
- next-level-cache = <&L2_0>;
- L1_I_3: l1-icache {
- compatible = "cache";
- };
- L1_D_3: l1-dcache {
- compatible = "cache";
- };
- };
-
- cpu-map {
- cluster0 {
- core0 {
- cpu = <&CPU4>;
- };
-
- core1 {
- cpu = <&CPU5>;
- };
-
- core2 {
- cpu = <&CPU6>;
- };
-
- core3 {
- cpu = <&CPU7>;
- };
- };
-
- cluster1 {
- core0 {
- cpu = <&CPU0>;
- };
-
- core1 {
- cpu = <&CPU1>;
- };
-
- core2 {
- cpu = <&CPU2>;
- };
-
- core3 {
- cpu = <&CPU3>;
- };
- };
- };
- };
-
- firmware {
- scm {
- compatible = "qcom,scm";
- };
- };
-
- memory {
- device_type = "memory";
- /* We expect the bootloader to fill in the reg */
- reg = <0 0 0 0>;
- };
-
- psci {
- compatible = "arm,psci-1.0";
- method = "smc";
- };
-
- timer {
- compatible = "arm,armv8-timer";
- interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>,
- <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>,
- <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>,
- <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>;
};
+};

- soc: soc {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0 0 0 0xffffffff>;
- compatible = "simple-bus";
-
- gcc: clock-controller@100000 {
- compatible = "qcom,gcc-sdm660";
- #clock-cells = <1>;
- #reset-cells = <1>;
- #power-domain-cells = <1>;
- reg = <0x00100000 0x94000>;
- };
-
- tlmm: pinctrl@3100000 {
- compatible = "qcom,sdm660-pinctrl";
- reg = <0x03100000 0x400000>,
- <0x03500000 0x400000>,
- <0x03900000 0x400000>;
- reg-names = "south", "center", "north";
- interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- gpio-ranges = <&tlmm 0 0 114>;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- uart_console_active: uart_console_active {
- pinmux {
- pins = "gpio4", "gpio5";
- function = "blsp_uart2";
- };
+&CPU0 {
+ compatible = "qcom,kryo260";
+ capacity-dmips-mhz = <1024>;
+ /delete-property/ operating-points-v2;
+};

- pinconf {
- pins = "gpio4", "gpio5";
- drive-strength = <2>;
- bias-disable;
- };
- };
- };
+&CPU1 {
+ compatible = "qcom,kryo260";
+ capacity-dmips-mhz = <1024>;
+ /delete-property/ operating-points-v2;
+};

- spmi_bus: spmi@800f000 {
- compatible = "qcom,spmi-pmic-arb";
- reg = <0x0800f000 0x1000>,
- <0x08400000 0x1000000>,
- <0x09400000 0x1000000>,
- <0x0a400000 0x220000>,
- <0x0800a000 0x3000>;
- reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
- interrupt-names = "periph_irq";
- interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>;
- qcom,ee = <0>;
- qcom,channel = <0>;
- #address-cells = <2>;
- #size-cells = <0>;
- interrupt-controller;
- #interrupt-cells = <4>;
- cell-index = <0>;
- };
+&CPU2 {
+ compatible = "qcom,kryo260";
+ capacity-dmips-mhz = <1024>;
+ /delete-property/ operating-points-v2;
+};

- blsp1_uart2: serial@c170000 {
- compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
- reg = <0x0c170000 0x1000>;
- interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
- <&gcc GCC_BLSP1_AHB_CLK>;
- clock-names = "core", "iface";
- status = "disabled";
- };
+&CPU3 {
+ compatible = "qcom,kryo260";
+ capacity-dmips-mhz = <1024>;
+ /delete-property/ operating-points-v2;
+};

- timer@17920000 {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- compatible = "arm,armv7-timer-mem";
- reg = <0x17920000 0x1000>;
+&CPU4 {
+ compatible = "qcom,kryo260";
+ capacity-dmips-mhz = <640>;
+ /delete-property/ operating-points-v2;
+};

- frame@17921000 {
- frame-number = <0>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x17921000 0x1000>,
- <0x17922000 0x1000>;
- };
+&CPU5 {
+ compatible = "qcom,kryo260";
+ capacity-dmips-mhz = <640>;
+ /delete-property/ operating-points-v2;
+};

- frame@17923000 {
- frame-number = <1>;
- interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x17923000 0x1000>;
- status = "disabled";
- };
+&CPU6 {
+ compatible = "qcom,kryo260";
+ capacity-dmips-mhz = <640>;
+ /delete-property/ operating-points-v2;
+};

- frame@17924000 {
- frame-number = <2>;
- interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x17924000 0x1000>;
- status = "disabled";
- };
+&CPU7 {
+ compatible = "qcom,kryo260";
+ capacity-dmips-mhz = <640>;
+ /delete-property/ operating-points-v2;
+};

- frame@17925000 {
- frame-number = <3>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x17925000 0x1000>;
- status = "disabled";
- };
+&gcc {
+ compatible = "qcom,gcc-sdm660";
+};

- frame@17926000 {
- frame-number = <4>;
- interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x17926000 0x1000>;
- status = "disabled";
- };
+&gpucc {
+ compatible = "qcom,gpucc-sdm660";
+};

- frame@17927000 {
- frame-number = <5>;
- interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x17927000 0x1000>;
- status = "disabled";
- };
+&mmcc {
+ compatible = "qcom,mmcc-sdm660";
+ /*
+ * 660 has one more dsi host/phy, which - when implemented
+ * and tested - should be added to the clocks property.
+ */
+};

- frame@17928000 {
- frame-number = <6>;
- interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x17928000 0x1000>;
- status = "disabled";
- };
- };
+&tlmm {
+ compatible = "qcom,sdm660-pinctrl";
+};

- intc: interrupt-controller@17a00000 {
- compatible = "arm,gic-v3";
- reg = <0x17a00000 0x10000>,
- <0x17b00000 0x100000>;
- #interrupt-cells = <3>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- interrupt-controller;
- #redistributor-regions = <1>;
- redistributor-stride = <0x0 0x20000>;
- interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
- };
- };
+&tsens {
+ #qcom,sensors = <14>;
};
--
2.32.0

Next message: Konrad Dybcio: "[PATCH 17/39] arm64: dts: qcom: sdm630: Add ADSP remoteproc configuration"
Previous message: Konrad Dybcio: "[PATCH 15/39] arm64: dts: qcom: sdm630: Add modem/ADSP SMP2P nodes"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]