Re: [PATCH V2 2/3] KVM: X86: Set the hardware DR6 only when KVM_DEBUGREG_WONT_EXIT
From: Paolo Bonzini
Date: Tue Aug 10 2021 - 06:08:02 EST
On 09/08/21 19:43, Lai Jiangshan wrote:
From: Lai Jiangshan <laijs@xxxxxxxxxxxxxxxxx>
Commit c77fb5fe6f03 ("KVM: x86: Allow the guest to run with dirty debug
registers") allows the guest accessing to DRs without exiting when
KVM_DEBUGREG_WONT_EXIT and we need to ensure that they are synchronized
on entry to the guest---including DR6 that was not synced before the commit.
But the commit sets the hardware DR6 not only when KVM_DEBUGREG_WONT_EXIT,
but also when KVM_DEBUGREG_BP_ENABLED. The second case is unnecessary
and just leads to a more case which leaks stale DR6 to the host which has
to be resolved by unconditionally reseting DR6 in kvm_arch_vcpu_put().
We'd better to set the hardware DR6 only when KVM_DEBUGREG_WONT_EXIT,
so that we can fine-grain control the cases when we need to reset it
which is done in later patch.
Signed-off-by: Lai Jiangshan <laijs@xxxxxxxxxxxxxxxxx>
---
arch/x86/kvm/x86.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c
index ad47a09ce307..d2aa49722064 100644
--- a/arch/x86/kvm/x86.c
+++ b/arch/x86/kvm/x86.c
@@ -9598,7 +9598,9 @@ static int vcpu_enter_guest(struct kvm_vcpu *vcpu)
set_debugreg(vcpu->arch.eff_db[1], 1);
set_debugreg(vcpu->arch.eff_db[2], 2);
set_debugreg(vcpu->arch.eff_db[3], 3);
- set_debugreg(vcpu->arch.dr6, 6);
+ /* When KVM_DEBUGREG_WONT_EXIT, dr6 is accessible in guest. */
+ if (vcpu->arch.switch_db_regs & KVM_DEBUGREG_WONT_EXIT)
+ set_debugreg(vcpu->arch.dr6, 6);
} else if (unlikely(hw_breakpoint_active())) {
set_debugreg(0, 7);
}
Even better, this should be moved to vmx.c's vcpu_enter_guest. This
matches the handling in svm.c:
/*
* Run with all-zero DR6 unless needed, so that we can get the exact cause
* of a #DB.
*/
if (unlikely(vcpu->arch.switch_db_regs & KVM_DEBUGREG_WONT_EXIT))
svm_set_dr6(svm, vcpu->arch.dr6);
else
svm_set_dr6(svm, DR6_ACTIVE_LOW);
That is,
KVM: X86: Set the hardware DR6 only when KVM_DEBUGREG_WONT_EXIT
Commit c77fb5fe6f03 ("KVM: x86: Allow the guest to run with dirty debug
registers") allows the guest accessing to DRs without exiting when
KVM_DEBUGREG_WONT_EXIT and we need to ensure that they are synchronized
on entry to the guest---including DR6 that was not synced before the commit.
But the commit sets the hardware DR6 not only when KVM_DEBUGREG_WONT_EXIT,
but also when KVM_DEBUGREG_BP_ENABLED. The second case is unnecessary
and just leads to a more case which leaks stale DR6 to the host which has
to be resolved by unconditionally reseting DR6 in kvm_arch_vcpu_put().
Even if KVM_DEBUGREG_WONT_EXIT, however, setting the host DR6 only matters
on VMX because SVM always uses the DR6 value from the VMCB. So move this
line to vmx.c and make it conditional on KVM_DEBUGREG_WONT_EXIT.
Signed-off-by: Paolo Bonzini <pbonzini@xxxxxxxxxx>
diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c
index ae8e62df16dd..21a3ef3012cf 100644
--- a/arch/x86/kvm/vmx/vmx.c
+++ b/arch/x86/kvm/vmx/vmx.c
@@ -6625,6 +6625,10 @@ static fastpath_t vmx_vcpu_run(struct kvm_vcpu *vcpu)
vmx->loaded_vmcs->host_state.cr4 = cr4;
}
+ /* When KVM_DEBUGREG_WONT_EXIT, dr6 is accessible in guest. */
+ if (vcpu->arch.switch_db_regs & KVM_DEBUGREG_WONT_EXIT)
+ set_debugreg(vcpu->arch.dr6, 6);
+
/* When single-stepping over STI and MOV SS, we must clear the
* corresponding interruptibility bits in the guest state. Otherwise
* vmentry fails as it then expects bit 14 (BS) in pending debug
diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c
index a111899ab2b4..fbc536b21585 100644
--- a/arch/x86/kvm/x86.c
+++ b/arch/x86/kvm/x86.c
@@ -9597,7 +9597,6 @@ static int vcpu_enter_guest(struct kvm_vcpu *vcpu)
set_debugreg(vcpu->arch.eff_db[1], 1);
set_debugreg(vcpu->arch.eff_db[2], 2);
set_debugreg(vcpu->arch.eff_db[3], 3);
- set_debugreg(vcpu->arch.dr6, 6);
} else if (unlikely(hw_breakpoint_active())) {
set_debugreg(0, 7);
}
Paolo