Re: [PATCH net-next 1/3] dt-bindings: net: fsl, fec: add "fsl, wakeup-irq" property
From: Rob Herring
Date: Fri Aug 13 2021 - 14:23:04 EST
On Wed, Aug 11, 2021 at 07:57:46AM +0000, Joakim Zhang wrote:
>
> Hi Andrew,
>
> > -----Original Message-----
> > From: Andrew Lunn <andrew@xxxxxxx>
> > Sent: 2021年8月10日 22:33
> > To: Joakim Zhang <qiangqing.zhang@xxxxxxx>
> > Cc: Florian Fainelli <f.fainelli@xxxxxxxxx>; davem@xxxxxxxxxxxxx;
> > kuba@xxxxxxxxxx; robh+dt@xxxxxxxxxx; shawnguo@xxxxxxxxxx;
> > s.hauer@xxxxxxxxxxxxxx; festevam@xxxxxxxxx; kernel@xxxxxxxxxxxxxx;
> > dl-linux-imx <linux-imx@xxxxxxx>; netdev@xxxxxxxxxxxxxxx;
> > devicetree@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> > Subject: Re: [PATCH net-next 1/3] dt-bindings: net: fsl, fec: add "fsl,
> > wakeup-irq" property
> >
> > > > > 1) FEC controller has up to 4 interrupt lines and all of these are
> > > > > routed to GIC
> > > > interrupt controller.
> > > > > 2) FEC has a wakeup interrupt signal and always are mixed with
> > > > > other
> > > > interrupt signals, and then output to one interrupt line.
> > > > > 3) For legacy SoCs, wakeup interrupt are mixed to int0 line, but
> > > > > for i.MX8M
> > > > serials, are mixed to int2 line.
> >
> > So you need to know which of the interrupts listed is the wake up interrupt.
We already have a way to do this by using 'wakeup' for the
interrupt-names entry. But I guess that ship has sailed here and that
wouldn't work well if not just a wakeup source (though you could repeat
an interrupt line that's the wakeup source).
> >
> > I can see a few ways to do this:
> >
> > The FEC driver already has quirks. Add a quirk to fec_imx8mq_info and
> > fec_imx8qm_info to indicate these should use int2.
Bingo!
Note that if the device is wakeup capable, it should have a
'wakeup-source' property in this case.
> >
> > or
> >
> > Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> >
> > b) two cells
> > ------------
> > The #interrupt-cells property is set to 2 and the first cell defines the
> > index of the interrupt within the controller, while the second cell is used
> > to specify any of the following flags:
> > - bits[3:0] trigger type and level flags
> > 1 = low-to-high edge triggered
> > 2 = high-to-low edge triggered
> > 4 = active high level-sensitive
> > 8 = active low level-sensitive
> >
> > You could add
> >
> > 18 = wakeup source
I'd be okay with this (though it should be a power of 2 number).
> >
> > and extend to core to either do all the work for you, or tell you this interrupt is
> > flagged as being a wakeup source. This solution has the advantage of it should
> > be usable in other drivers.
Another option is couldn't you just enable all the interrupts as wakeup
sources? Presumably, only one of them would trigger a wakeup.
>
> Thanks a lot for your comments first!
>
> I just look into the irq code, if we extend bit[5] to carry wakeup info ( due to bit[4] is used for IRQ_TYPE_PROBE),
> then configure it in the TYPE field of 'interrupts' property, so that interrupt controller would know which interrupt
> is wakeup capable.
> I think there is no much work core would do, may just set this interrupt wakup capable. Another functionality is
> driver side get this info to identify which mixed interrupt has wakeup capability, we can export symbol from kernel/irq/irqdomain.c.
>
> The intention is to let driver know which interrupt is wakeup capable, I would choose to provider this in specific driver,
> instead of interrupt controller, it seems to me that others may all choose this solution for wakeup mixed interrupt.
>
> So I would prefer solution 1, it's easier and under-control. I can have a try if you strongly recommend solution 2.
>
> Best Regards,
> Joakim Zhang
> > Andrew