[PATCH v3 2/2] phy: qcom-qmp: Add support for SM6115 UFS phy

From: Iskren Chernev
Date: Sat Aug 21 2021 - 11:57:14 EST

Next message: Greg KH: "[GIT PULL] USB fix for 5.14-rc7"
Previous message: Iskren Chernev: "[PATCH v3 1/2] dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings"
In reply to: Iskren Chernev: "[PATCH v3 1/2] dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings"
Next in thread: Vinod Koul: "Re: [PATCH v3 0/2] Add UFS PHY support for SM6115/4250"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Add the tables and constants for init sequences for UFS QMP phy found in
SM4250/6115 SoC. The phy is a variation of the v2 phy, but is mistakenly
labeled as v3-660 in downstream sources.

QSERDES COM, RX, TX registers match fully existing v2 registers, with
a few additions. PCS registers don't have much in common, but there are
no clashes with existing ones so new registers were added to existing v2
PCS pack.

Signed-off-by: Iskren Chernev <iskren.chernev@xxxxxxxxx>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 124 ++++++++++++++++++++++++++++
drivers/phy/qualcomm/phy-qcom-qmp.h | 18 ++++
2 files changed, 142 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index a8c4368f984b..f14032170b1c 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -234,6 +234,11 @@ static const unsigned int sdm845_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
[QPHY_PCS_READY_STATUS] = 0x160,
};

+static const unsigned int sm6115_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
+ [QPHY_START_CTRL] = 0x00,
+ [QPHY_PCS_READY_STATUS] = 0x168,
+};
+
static const unsigned int sm8250_pcie_regs_layout[QPHY_LAYOUT_SIZE] = {
[QPHY_SW_RESET] = 0x00,
[QPHY_START_CTRL] = 0x44,
@@ -1329,6 +1334,97 @@ static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_pcs_tbl[] = {
QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG2, 0x60),
};

+static const struct qmp_phy_init_tbl sm6115_ufsphy_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x0e),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x30),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV_MODE1, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_EN, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_CTRL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_RESETSM_CNTRL, 0x20),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_CFG, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER1, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER2, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x05),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE1_MODE0, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE2_MODE0, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE1, 0x98),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE1, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE1, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE1, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE1, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE1_MODE1, 0xd6),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE2_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE1, 0x32),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE1, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_INITVAL1, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_INITVAL2, 0x00),
+
+ /* Rate B */
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x44),
+};
+
+static const struct qmp_phy_init_tbl sm6115_ufsphy_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
+ QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06),
+};
+
+static const struct qmp_phy_init_tbl sm6115_ufsphy_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x24),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_CNTRL, 0x0F),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_INTERFACE_MODE, 0x40),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x1E),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0B),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_TERM_BW, 0x5B),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_GAIN1_LSB, 0xFF),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_GAIN1_MSB, 0x3F),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_GAIN2_LSB, 0xFF),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_GAIN2_MSB, 0x3F),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0D),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SVS_SO_GAIN_HALF, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SVS_SO_GAIN_QUARTER, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SVS_SO_GAIN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x5B),
+};
+
+static const struct qmp_phy_init_tbl sm6115_ufsphy_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_RX_PWM_GEAR_BAND, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_RX_SIGDET_CTRL2, 0x6d),
+ QMP_PHY_INIT_CFG(QPHY_TX_LARGE_AMP_DRV_LVL, 0x0f),
+ QMP_PHY_INIT_CFG(QPHY_TX_SMALL_AMP_DRV_LVL, 0x02),
+ QMP_PHY_INIT_CFG(QPHY_RX_MIN_STALL_NOCONFIG_TIME_CAP, 0x28),
+ QMP_PHY_INIT_CFG(QPHY_RX_SYM_RESYNC_CTRL, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_TX_LARGE_AMP_POST_EMP_LVL, 0x12),
+ QMP_PHY_INIT_CFG(QPHY_TX_SMALL_AMP_POST_EMP_LVL, 0x0f),
+ QMP_PHY_INIT_CFG(QPHY_RX_MIN_HIBERN8_TIME, 0x9a), /* 8 us */
+};
+
static const struct qmp_phy_init_tbl sdm845_ufsphy_serdes_tbl[] = {
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x04),
@@ -3396,6 +3492,31 @@ static const struct qmp_phy_cfg sdm845_ufsphy_cfg = {
.no_pcs_sw_reset = true,
};

+static const struct qmp_phy_cfg sm6115_ufsphy_cfg = {
+ .type = PHY_TYPE_UFS,
+ .nlanes = 1,
+
+ .serdes_tbl = sm6115_ufsphy_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(sm6115_ufsphy_serdes_tbl),
+ .tx_tbl = sm6115_ufsphy_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(sm6115_ufsphy_tx_tbl),
+ .rx_tbl = sm6115_ufsphy_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(sm6115_ufsphy_rx_tbl),
+ .pcs_tbl = sm6115_ufsphy_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(sm6115_ufsphy_pcs_tbl),
+ .clk_list = sdm845_ufs_phy_clk_l,
+ .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
+ .regs = sm6115_ufsphy_regs_layout,
+
+ .start_ctrl = SERDES_START,
+ .pwrdn_ctrl = SW_PWRDN,
+
+ .is_dual_lane_phy = false,
+ .no_pcs_sw_reset = true,
+};
+
static const struct qmp_phy_cfg msm8998_pciephy_cfg = {
.type = PHY_TYPE_PCIE,
.nlanes = 1,
@@ -5444,6 +5565,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
}, {
.compatible = "qcom,msm8998-qmp-usb3-phy",
.data = &msm8998_usb3phy_cfg,
+ }, {
+ .compatible = "qcom,sm6115-qmp-ufs-phy",
+ .data = &sm6115_ufsphy_cfg,
}, {
.compatible = "qcom,sm8150-qmp-ufs-phy",
.data = &sm8150_ufsphy_cfg,
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index 6592b58b13f6..bebeac2c091c 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -191,6 +191,8 @@
#define QSERDES_COM_VCO_TUNE2_MODE0 0x130
#define QSERDES_COM_VCO_TUNE1_MODE1 0x134
#define QSERDES_COM_VCO_TUNE2_MODE1 0x138
+#define QSERDES_COM_VCO_TUNE_INITVAL1 0x13c
+#define QSERDES_COM_VCO_TUNE_INITVAL2 0x140
#define QSERDES_COM_VCO_TUNE_TIMER1 0x144
#define QSERDES_COM_VCO_TUNE_TIMER2 0x148
#define QSERDES_COM_BG_CTRL 0x170
@@ -220,6 +222,10 @@
/* Only for QMP V2 PHY - RX registers */
#define QSERDES_RX_UCDR_SO_GAIN_HALF 0x010
#define QSERDES_RX_UCDR_SO_GAIN 0x01c
+#define QSERDES_RX_UCDR_SVS_SO_GAIN_HALF 0x030
+#define QSERDES_RX_UCDR_SVS_SO_GAIN_QUARTER 0x034
+#define QSERDES_RX_UCDR_SVS_SO_GAIN_EIGHTH 0x038
+#define QSERDES_RX_UCDR_SVS_SO_GAIN 0x03c
#define QSERDES_RX_UCDR_FASTLOCK_FO_GAIN 0x040
#define QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE 0x048
#define QSERDES_RX_RX_TERM_BW 0x090
@@ -243,6 +249,10 @@
#define QPHY_POWER_DOWN_CONTROL 0x04
#define QPHY_TXDEEMPH_M6DB_V0 0x24
#define QPHY_TXDEEMPH_M3P5DB_V0 0x28
+#define QPHY_TX_LARGE_AMP_DRV_LVL 0x34
+#define QPHY_TX_LARGE_AMP_POST_EMP_LVL 0x38
+#define QPHY_TX_SMALL_AMP_DRV_LVL 0x3c
+#define QPHY_TX_SMALL_AMP_POST_EMP_LVL 0x40
#define QPHY_ENDPOINT_REFCLK_DRIVE 0x54
#define QPHY_RX_IDLE_DTCT_CNTRL 0x58
#define QPHY_POWER_STATE_CONFIG1 0x60
@@ -253,6 +263,11 @@
#define QPHY_LOCK_DETECT_CONFIG3 0x88
#define QPHY_PWRUP_RESET_DLY_TIME_AUXCLK 0xa0
#define QPHY_LP_WAKEUP_DLY_TIME_AUXCLK 0xa4
+#define QPHY_RX_MIN_STALL_NOCONFIG_TIME_CAP 0xcc
+#define QPHY_RX_SYM_RESYNC_CTRL 0x13c
+#define QPHY_RX_MIN_HIBERN8_TIME 0x140
+#define QPHY_RX_SIGDET_CTRL2 0x148
+#define QPHY_RX_PWM_GEAR_BAND 0x154
#define QPHY_PLL_LOCK_CHK_DLY_TIME_AUXCLK_LSB 0x1A8
#define QPHY_OSC_DTCT_ACTIONS 0x1AC
#define QPHY_RX_SIGDET_LVL 0x1D8
@@ -280,6 +295,8 @@
#define QSERDES_V3_COM_SSC_PER2 0x020
#define QSERDES_V3_COM_SSC_STEP_SIZE1 0x024
#define QSERDES_V3_COM_SSC_STEP_SIZE2 0x028
+#define QSERDES_V3_COM_POST_DIV 0x02c
+#define QSERDES_V3_COM_POST_DIV_MUX 0x030
#define QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN 0x034
# define QSERDES_V3_COM_BIAS_EN 0x0001
# define QSERDES_V3_COM_BIAS_EN_MUX 0x0002
@@ -291,6 +308,7 @@
#define QSERDES_V3_COM_CLK_ENABLE1 0x038
#define QSERDES_V3_COM_SYS_CLK_CTRL 0x03c
#define QSERDES_V3_COM_SYSCLK_BUF_ENABLE 0x040
+#define QSERDES_V3_COM_PLL_EN 0x044
#define QSERDES_V3_COM_PLL_IVCO 0x048
#define QSERDES_V3_COM_LOCK_CMP1_MODE0 0x098
#define QSERDES_V3_COM_LOCK_CMP2_MODE0 0x09c
--
2.32.0

Next message: Greg KH: "[GIT PULL] USB fix for 5.14-rc7"
Previous message: Iskren Chernev: "[PATCH v3 1/2] dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings"
In reply to: Iskren Chernev: "[PATCH v3 1/2] dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings"
Next in thread: Vinod Koul: "Re: [PATCH v3 0/2] Add UFS PHY support for SM6115/4250"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]