Re: [PATCH v2] usb: chipidea: add loop timeout for hw_ep_set_halt()

[Jeaho Hwang]

2021년 8월 28일 (토) 오전 10:38, Peter Chen <peter.chen@xxxxxxxxxx>님이 작성:
>
> On 21-08-27 10:35:05, Jeaho Hwang wrote:
> > 2021년 8월 27일 (금) 오전 8:08, Peter Chen <peter.chen@xxxxxxxxxx>님이 작성:
> > >
> > > On 21-08-24 17:31:44, Jeaho Hwang wrote:
> > > > 2021년 8월 17일 (화) 오후 3:44, Jeaho Hwang <jhhwang@xxxxxxxxxx>님이 작성:
> > > > >
> > > > > If ctrl EP priming is failed (very rare case in standard linux),
> > > > > hw_ep_set_halt goes infinite loop. waiting 100 times was enough
> > > > > for zynq7000.
> > > > >
> > > >
> > > > Hi Peter.
> > > > I found from zynq7000 TRM that the hardware clears Stall bit if a
> > > > setup packet is received on a control endpoint.
> > > > I think hw_ep_set_halt goes infinite loop since:
> > > >
> > > > 1. hw_ep_prime for control EP which is called from
> > > > isr_tr_complete_handler -> isr_setup_status_phase is failed due to a
> > > > setup packet received.
> > >
> > > How do you know that? Do you observe the new setup packet on the bus
> > > before the current status stage? Usually, the host doesn't begin new setup
> > > transfer before current setup transfer has finished.
> > >
> > > Peter
> > >
> >
> > I found an error return from the second ENDPTSETUPSTAT checking
> > routine, then setting the stall bit(TXS) kept failing. So I guessed it
> > is due to a setup packet received.
> > I didn't observe the setup packet by e.g. HW probes. Any other reason
> > to produce that symptom?
>
> I guess two possible reasons for that:
> - The new setup is coming after priming
> - The interrupt occurs after prime, and when the back from interrupt,
> other thread for USB transfer is scheduled, eg, usb_ep_queue from RNDIS
>
> From your experiments and observation, it seems the first reason is not possible.

I will check if any other thread calls udc. but the only workload
using RNDIS was the host side ping sender.
Thanks for the advice.

> Did your get failure with UP system?

I'm sorry I don't understand what UP system means.

>
> Peter
>
> >
> > For reminder, only reproduced on preemp_rt kernel and with Windows(10)
> > RNDIS host.
> >
> > thanks.
> >
> >
> > > > 2. in isr_tr_complete_handler it tries to call _ep_set_halt if either
> > > > isr_tr_complete_low or isr_setup_status_phase returns error.
> > > > 3. Since the control EP got a setup packet, HW resets TXS bit just as
> > > > the driver sets inside hw_ep_set_halt so it goes infinite loop.
> > > >
> > > > Does it make sense? If it is right, we shouldn't call _ep_set_halt if
> > > > the err is -EAGAIN, which could be returned ONLY due to the setup
> > > > packet issue described above.
> > > > And the loop timeout is not required anymore.
> > > >
> > > > Can I ask your opinion on this, Peter and USB experts?
> > > >
> > > > Thanks.
> > > >
>
> --
>
> Thanks,
> Peter Chen
>


-- 
황재호, Jay Hwang, linux team manager of RTst
010-7242-1593