Re: [PATCHv3 1/6] ARM: dts: meson8b: odroidc1: Add usb phy power node

[Anand Moon]

Hi Neil / Martin,

Thanks for your review comments.

On Tue, 31 Aug 2021 at 20:20, Neil Armstrong <narmstrong@xxxxxxxxxxxx> wrote:
>
> Hi,
>
> On 30/08/2021 21:37, Martin Blumenstingl wrote:
> > Hi Neil,
> >
> > On Mon, Aug 30, 2021 at 9:45 AM Neil Armstrong <narmstrong@xxxxxxxxxxxx> wrote:
> >>
> >> Hi,
> >>
> >> On 17/08/2021 06:15, Anand Moon wrote:
> >>> Add missing usb phy power node for usb node fix below warning.
> >>> P5V0 regulator supply input voltage range to USB host controller.
> >>> As described in the C1+ schematics, GPIO GPIOAO_5 is used to
> >>> enable input power to USB ports, set it to Active Low.
> >>>
> >>> [    1.260772] dwc2 c90c0000.usb: Looking up vbus-supply from device tree
> >>> [    1.260784] dwc2 c90c0000.usb: Looking up vbus-supply property in
> >>>               mode /soc/usb@c90c0000 failed
> >>
> >> First of all, DT is not here to fix boot message.
> > Anand mentioned elsewhere that this is a debug/info message
> >
> >> Finally, I looked at the Odroid-C1 schematics and the GPIOAO.BIT5 is an input
> >> to the S805, and the PWREN signal is controlled by the USB Hub so this regulator
> >> should not be added at all.
> > I think there's a misunderstanding because there's two PWREN signals
> > with different meanings.
> > The PWREN signal for the USB host ports is hard-wired and not
> > connected to the SoC at all.
> > The PWREN signal for the Micro-USB port (which Anand is adding here)
> > is controlled by GPIOAO_5. odroid-c1+_rev0.4_20150615.pdf [0] shows it
> > as an input to "USB_OTG" on page 1. "USB_OTG" consists of a power
> > switch and the connector itself as shown on page 28.
> >
> > Personally I think that the change from Anand itself is good.
> > If you feel otherwise then please speak up.
>
> Ok thanks for the clarification, then the change is ok, but not the commit message.
>
> >> Add missing usb phy power node for usb node fix below warning.
>
> is not a good reason for a DT change. A proper reason should be added.
>
> And the commit message doesn't specify the change is for the Micro-USB port,
> this should be clarified.
>
> Neil
>
> > As I pointed out three smaller changes I am hoping that Anand will
> > re-send the updated patch anyways. At that point he can also add the
> > changes from your feedback.
> >
Ok I will try to address your feedback in the next version.

After enabling CONFIG_REGULATOR_DEBUG, with this patch applied
I still not getting the USB regulator to enable.
Do you see different output at your end?

On Odroid C1+
[    5.737571] reg-fixed-voltage regulator-usb-pwr-en: GPIO lookup for
consumer (null)
[    5.737630] reg-fixed-voltage regulator-usb-pwr-en: using device
tree for GPIO lookup
[    5.737711] of_get_named_gpiod_flags: can't parse 'gpios' property
of node '/regulator-usb-pwr-en[0]'
[    5.737906] of_get_named_gpiod_flags: parsed 'gpio' property of
node '/regulator-usb-pwr-en[0]' - status (0)
[    5.738209] gpio_stub_drv gpiochip0: Persistence not supported for GPIO 5
[    5.738490] USB_OTG_PWR: 5000 mV, disabled
[    5.740313] reg-fixed-voltage regulator-usb-pwr-en: Looking up
vin-supply from device tree
[    5.740394] USB_OTG_PWR: supplied by P5V0
[    5.741235] reg-fixed-voltage regulator-usb-pwr-en: USB_OTG_PWR
supplying 5000000uV

Odroid N2.
[    3.047813] reg-fixed-voltage regulator-hub_5v: HUB_5V supplying 5000000uV
[    3.049282] reg-fixed-voltage regulator-usb_pwr_en: GPIO lookup for
consumer (null)
[    3.049305] reg-fixed-voltage regulator-usb_pwr_en: using device
tree for GPIO lookup
[    3.049370] of_get_named_gpiod_flags: can't parse 'gpios' property
of node '/regulator-usb_pwr_en[0]'
[    3.049500] of_get_named_gpiod_flags: parsed 'gpio' property of
node '/regulator-usb_pwr_en[0]' - status (0)
[    3.049622] gpio_stub_drv gpiochip0: Persistence not supported for GPIO 22
[    3.049759] USB_PWR_EN: 5000 mV, disabled
[    3.051257] reg-fixed-voltage regulator-usb_pwr_en: Looking up
vin-supply from device tree
[    3.051320] USB_PWR_EN: supplied by 5V

Thanks
-Anand



> >
> > Best regards,
> > Martin
> >
> >
> > [0] https://dn.odroid.com/S805/Schematics/odroid-c1+_rev0.4_20150615.pdf
> >
>