RE: [PATCH v2 3/4] arm64: dts: imx8mm: add the pcie phy support

[Richard Zhu]

> -----Original Message-----
> From: Lucas Stach <l.stach@xxxxxxxxxxxxxx>
> Sent: Monday, September 27, 2021 4:35 PM
> To: Richard Zhu <hongxing.zhu@xxxxxxx>; kishon@xxxxxx; vkoul@xxxxxxxxxx;
> robh@xxxxxxxxxx; galak@xxxxxxxxxxxxxxxxxxx; shawnguo@xxxxxxxxxx
> Cc: linux-phy@xxxxxxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx;
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> kernel@xxxxxxxxxxxxxx; dl-linux-imx <linux-imx@xxxxxxx>
> Subject: Re: [PATCH v2 3/4] arm64: dts: imx8mm: add the pcie phy support
> 
> Am Sonntag, dem 26.09.2021 um 15:39 +0800 schrieb Richard Zhu:
> > Add the PCIe PHY support on iMX8MM platforms.
> >
> > Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
> > ---
> >  arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi |  4 ++++
> >  arch/arm64/boot/dts/freescale/imx8mm.dtsi     | 12 ++++++++++++
> 
> This should be split into 2 patches: one for the SoC and one for the EVK board.
> 
[Richard Zhu] Okay, would split this patch into 2 patches later. Thanks.

> >  2 files changed, 16 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > index e033d0257b5a..e7f398433486 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > @@ -289,6 +289,10 @@ pca6416: gpio@20 {
> >  	};
> >  };
> >
> > +&pcie_phy {
> > +	status = "okay";
> > +};
> > +
> >  &sai3 {
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&pinctrl_sai3>;
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > index e7648c3b8390..de231d531ba4 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > @@ -998,6 +998,18 @@ usbmisc2: usbmisc@32e50200 {
> >  				reg = <0x32e50200 0x200>;
> >  			};
> >
> > +			pcie_phy: pcie-phy@32f00000 {
> > +				compatible = "fsl,imx8mm-pcie-phy";
> > +				reg = <0x32f00000 0x10000>;
> > +				clocks = <&clk IMX8MM_CLK_PCIE1_PHY>;
> > +				clock-names = "phy";
> > +				assigned-clocks = <&clk IMX8MM_CLK_PCIE1_PHY>;
> > +				assigned-clock-rates = <100000000>;
> > +				assigned-clock-parents = <&clk
> IMX8MM_SYS_PLL2_100M>;
> > +				#phy-cells = <0>;
> > +				fsl,refclk-pad-mode = <1>;
> 
> Move this to the board DT, as the pad mode is a board level decision.
> Also use the enum instead of raw value.
[Richard Zhu] Got that, thanks.
> 
> > +				status = "disabled";
> > +			};
> >  		};
> >
> >  		dma_apbh: dma-controller@33000000 {
>