Re: [PATCH v9 3/4] arm64: dts: qcom: sc7280: Add PCIe nodes for IDP board

[Stephen Boyd]

Quoting Prasad Malisetty (2021-09-28 06:55:49)
> Enable PCIe controller and PHY for sc7280 IDP board.
> Add specific NVMe GPIO entries for SKU1 and SKU2 support.
>
> Signed-off-by: Prasad Malisetty <pmaliset@xxxxxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/sc7280-idp.dts  |  9 ++++++
>  arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 54 ++++++++++++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/sc7280-idp2.dts |  9 ++++++
>  3 files changed, 72 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> index 64fc22a..1562386 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> @@ -61,6 +61,15 @@
>         modem-init;
>  };
>
> +&nvme_pwren_pin {
> +       pins = "gpio19";
> +};

This should move to the bottom in the "pinctrl" section.

> +
> +&nvme_3v3_regulators {
> +       gpio = <&tlmm 19 GPIO_ACTIVE_HIGH>;
> +       enable-active-high;

The enable-active-high can be in the idp.dtsi file? That doesn't seem to
change.

> +};
> +
>  &pmk8350_vadc {
>         pmr735a_die_temp {
>                 reg = <PMR735A_ADC7_DIE_TEMP>;
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> index def22ff..5b5505f 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> @@ -31,6 +31,17 @@
>                         linux,can-disable;
>                 };
>         };
> +
> +       nvme_3v3_regulators: nvme-3v3-regulators {

Why plural? Isn't it a single regulator?

> +               compatible = "regulator-fixed";
> +               regulator-name = "VLDO_3V3";
> +
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&nvme_pwren_pin>;
> +       };
>  };
>
>  &apps_rsc {
> @@ -220,6 +231,42 @@
>         modem-init;
>  };
>
> +&pcie1 {
> +       status = "okay";
> +       perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
> +
> +       vddpe-3v3-supply = <&nvme_3v3_regulators>;
> +
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pcie1_default_state>;
> +};
> +
> +&pcie1_phy {
> +       status = "okay";
> +
> +       vdda-phy-supply = <&vreg_l10c_0p8>;
> +       vdda-pll-supply = <&vreg_l6b_1p2>;
> +};
> +
> +&pcie1_default_state {

I thought the node would be split into a reset config node and a wake
config node. Is that not being done for some reason? The pinctrl-0 would
look like

	pinctrl-0 = <&pcie1_default_state>, <&pcie1_reset_n>, <&pcie1_wake_n>;

> +       reset-n {
> +               pins = "gpio2";
> +               function = "gpio";
> +
> +               drive-strength = <16>;
> +               output-low;
> +               bias-disable;
> +       };
> +
> +       wake-n {
> +               pins = "gpio3";
> +               function = "gpio";
> +
> +               drive-strength = <2>;
> +               bias-pull-up;
> +       };
> +};
> +
>  &pmk8350_vadc {
>         pmk8350_die_temp {
>                 reg = <PMK8350_ADC7_DIE_TEMP>;
> @@ -489,3 +536,10 @@
>                 bias-pull-up;
>         };
>  };
> +
> +&tlmm {
> +       nvme_pwren_pin: nvme-pwren-pin {
> +               function = "gpio";
> +               bias-pull-up;
> +       };
> +};
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
> index 1fc2add..0548cb6 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
> @@ -21,3 +21,12 @@
>                 stdout-path = "serial0:115200n8";
>         };
>  };
> +
> +&nvme_pwren_pin {
> +       pins = "gpio51";
> +};

The pin config can go to a pinctrl section at the bottom of this file?

> +
> +&nvme_3v3_regulators {
> +       gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
> +       enable-active-high;
> +};