linux-next: manual merge of the net-next tree with the net tree

From: Stephen Rothwell
Date: Wed Sep 29 2021 - 21:41:45 EST

Next message: Alan Stern: "Re: [PATCH v2 1/6] driver core: Move the "authorized" attribute from USB/Thunderbolt to core"
Previous message: Matteo Croce: "Re: [PATCH v5 1/3] riscv: optimized memcpy"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi all,

Today's linux-next merge of the net-next tree got a conflict in:

drivers/net/phy/bcm7xxx.c

between commit:

d88fd1b546ff ("net: phy: bcm7xxx: Fixed indirect MMD operations")

from the net tree and commit:

f68d08c437f9 ("net: phy: bcm7xxx: Add EPHY entry for 72165")

from the net-next tree.

I fixed it up (see below) and can carry the fix as necessary. This
is now fixed as far as linux-next is concerned, but any non trivial
conflicts should be mentioned to your upstream maintainer when your tree
is submitted for merging. You may also want to consider cooperating
with the maintainer of the conflicting tree to minimise any particularly
complex conflicts.

--
Cheers,
Stephen Rothwell

diff --cc drivers/net/phy/bcm7xxx.c
index 27b6a3f507ae,3a29a1493ff1..000000000000
--- a/drivers/net/phy/bcm7xxx.c
+++ b/drivers/net/phy/bcm7xxx.c
@@@ -415,93 -398,190 +415,277 @@@ static int bcm7xxx_28nm_ephy_config_ini
return bcm7xxx_28nm_ephy_apd_enable(phydev);
}

+#define MII_BCM7XXX_REG_INVALID 0xff
+
+static u8 bcm7xxx_28nm_ephy_regnum_to_shd(u16 regnum)
+{
+ switch (regnum) {
+ case MDIO_CTRL1:
+ return MII_BCM7XXX_SHD_3_PCS_CTRL;
+ case MDIO_STAT1:
+ return MII_BCM7XXX_SHD_3_PCS_STATUS;
+ case MDIO_PCS_EEE_ABLE:
+ return MII_BCM7XXX_SHD_3_EEE_CAP;
+ case MDIO_AN_EEE_ADV:
+ return MII_BCM7XXX_SHD_3_AN_EEE_ADV;
+ case MDIO_AN_EEE_LPABLE:
+ return MII_BCM7XXX_SHD_3_EEE_LP;
+ case MDIO_PCS_EEE_WK_ERR:
+ return MII_BCM7XXX_SHD_3_EEE_WK_ERR;
+ default:
+ return MII_BCM7XXX_REG_INVALID;
+ }
+}
+
+static bool bcm7xxx_28nm_ephy_dev_valid(int devnum)
+{
+ return devnum == MDIO_MMD_AN || devnum == MDIO_MMD_PCS;
+}
+
+static int bcm7xxx_28nm_ephy_read_mmd(struct phy_device *phydev,
+ int devnum, u16 regnum)
+{
+ u8 shd = bcm7xxx_28nm_ephy_regnum_to_shd(regnum);
+ int ret;
+
+ if (!bcm7xxx_28nm_ephy_dev_valid(devnum) ||
+ shd == MII_BCM7XXX_REG_INVALID)
+ return -EOPNOTSUPP;
+
+ /* set shadow mode 2 */
+ ret = __phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
+ MII_BCM7XXX_SHD_MODE_2, 0);
+ if (ret < 0)
+ return ret;
+
+ /* Access the desired shadow register address */
+ ret = __phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL, shd);
+ if (ret < 0)
+ goto reset_shadow_mode;
+
+ ret = __phy_read(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT);
+
+reset_shadow_mode:
+ /* reset shadow mode 2 */
+ __phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0,
+ MII_BCM7XXX_SHD_MODE_2);
+ return ret;
+}
+
+static int bcm7xxx_28nm_ephy_write_mmd(struct phy_device *phydev,
+ int devnum, u16 regnum, u16 val)
+{
+ u8 shd = bcm7xxx_28nm_ephy_regnum_to_shd(regnum);
+ int ret;
+
+ if (!bcm7xxx_28nm_ephy_dev_valid(devnum) ||
+ shd == MII_BCM7XXX_REG_INVALID)
+ return -EOPNOTSUPP;
+
+ /* set shadow mode 2 */
+ ret = __phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
+ MII_BCM7XXX_SHD_MODE_2, 0);
+ if (ret < 0)
+ return ret;
+
+ /* Access the desired shadow register address */
+ ret = __phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL, shd);
+ if (ret < 0)
+ goto reset_shadow_mode;
+
+ /* Write the desired value in the shadow register */
+ __phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT, val);
+
+reset_shadow_mode:
+ /* reset shadow mode 2 */
+ return __phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0,
+ MII_BCM7XXX_SHD_MODE_2);
+}
+
+ static int bcm7xxx_16nm_ephy_afe_config(struct phy_device *phydev)
+ {
+ int tmp, rcalcode, rcalnewcodelp, rcalnewcode11, rcalnewcode11d2;
+
+ /* Reset PHY */
+ tmp = genphy_soft_reset(phydev);
+ if (tmp)
+ return tmp;
+
+ /* Reset AFE and PLL */
+ bcm_phy_write_exp_sel(phydev, 0x0003, 0x0006);
+ /* Clear reset */
+ bcm_phy_write_exp_sel(phydev, 0x0003, 0x0000);
+
+ /* Write PLL/AFE control register to select 54MHz crystal */
+ bcm_phy_write_misc(phydev, 0x0030, 0x0001, 0x0000);
+ bcm_phy_write_misc(phydev, 0x0031, 0x0000, 0x044a);
+
+ /* Change Ka,Kp,Ki to pdiv=1 */
+ bcm_phy_write_misc(phydev, 0x0033, 0x0002, 0x71a1);
+ /* Configuration override */
+ bcm_phy_write_misc(phydev, 0x0033, 0x0001, 0x8000);
+
+ /* Change PLL_NDIV and PLL_NUDGE */
+ bcm_phy_write_misc(phydev, 0x0031, 0x0001, 0x2f68);
+ bcm_phy_write_misc(phydev, 0x0031, 0x0002, 0x0000);
+
+ /* Reference frequency is 54Mhz, config_mode[15:14] = 3 (low
+ * phase)
+ */
+ bcm_phy_write_misc(phydev, 0x0030, 0x0003, 0xc036);
+
+ /* Initialize bypass mode */
+ bcm_phy_write_misc(phydev, 0x0032, 0x0003, 0x0000);
+ /* Bypass code, default: VCOCLK enabled */
+ bcm_phy_write_misc(phydev, 0x0033, 0x0000, 0x0002);
+ /* LDOs at default setting */
+ bcm_phy_write_misc(phydev, 0x0030, 0x0002, 0x01c0);
+ /* Release PLL reset */
+ bcm_phy_write_misc(phydev, 0x0030, 0x0001, 0x0001);
+
+ /* Bandgap curvature correction to correct default */
+ bcm_phy_write_misc(phydev, 0x0038, 0x0000, 0x0010);
+
+ /* Run RCAL */
+ bcm_phy_write_misc(phydev, 0x0039, 0x0003, 0x0038);
+ bcm_phy_write_misc(phydev, 0x0039, 0x0003, 0x003b);
+ udelay(2);
+ bcm_phy_write_misc(phydev, 0x0039, 0x0003, 0x003f);
+ mdelay(5);
+
+ /* AFE_CAL_CONFIG_0, Vref=1000, Target=10, averaging enabled */
+ bcm_phy_write_misc(phydev, 0x0039, 0x0001, 0x1c82);
+ /* AFE_CAL_CONFIG_0, no reset and analog powerup */
+ bcm_phy_write_misc(phydev, 0x0039, 0x0001, 0x9e82);
+ udelay(2);
+ /* AFE_CAL_CONFIG_0, start calibration */
+ bcm_phy_write_misc(phydev, 0x0039, 0x0001, 0x9f82);
+ udelay(100);
+ /* AFE_CAL_CONFIG_0, clear start calibration, set HiBW */
+ bcm_phy_write_misc(phydev, 0x0039, 0x0001, 0x9e86);
+ udelay(2);
+ /* AFE_CAL_CONFIG_0, start calibration with hi BW mode set */
+ bcm_phy_write_misc(phydev, 0x0039, 0x0001, 0x9f86);
+ udelay(100);
+
+ /* Adjust 10BT amplitude additional +7% and 100BT +2% */
+ bcm_phy_write_misc(phydev, 0x0038, 0x0001, 0xe7ea);
+ /* Adjust 1G mode amplitude and 1G testmode1 */
+ bcm_phy_write_misc(phydev, 0x0038, 0x0002, 0xede0);
+
+ /* Read CORE_EXPA9 */
+ tmp = bcm_phy_read_exp(phydev, 0x00a9);
+ /* CORE_EXPA9[6:1] is rcalcode[5:0] */
+ rcalcode = (tmp & 0x7e) / 2;
+ /* Correct RCAL code + 1 is -1% rprogr, LP: +16 */
+ rcalnewcodelp = rcalcode + 16;
+ /* Correct RCAL code + 1 is -15 rprogr, 11: +10 */
+ rcalnewcode11 = rcalcode + 10;
+ /* Saturate if necessary */
+ if (rcalnewcodelp > 0x3f)
+ rcalnewcodelp = 0x3f;
+ if (rcalnewcode11 > 0x3f)
+ rcalnewcode11 = 0x3f;
+ /* REXT=1 BYP=1 RCAL_st1<5:0>=new rcal code */
+ tmp = 0x00f8 + rcalnewcodelp * 256;
+ /* Program into AFE_CAL_CONFIG_2 */
+ bcm_phy_write_misc(phydev, 0x0039, 0x0003, tmp);
+ /* AFE_BIAS_CONFIG_0 10BT bias code (Bias: E4) */
+ bcm_phy_write_misc(phydev, 0x0038, 0x0001, 0xe7e4);
+ /* invert adc clock output and 'adc refp ldo current To correct
+ * default
+ */
+ bcm_phy_write_misc(phydev, 0x003b, 0x0000, 0x8002);
+ /* 100BT stair case, high BW, 1G stair case, alternate encode */
+ bcm_phy_write_misc(phydev, 0x003c, 0x0003, 0xf882);
+ /* 1000BT DAC transition method per Erol, bits[32], DAC Shuffle
+ * sequence 1 + 10BT imp adjust bits
+ */
+ bcm_phy_write_misc(phydev, 0x003d, 0x0000, 0x3201);
+ /* Non-overlap fix */
+ bcm_phy_write_misc(phydev, 0x003a, 0x0002, 0x0c00);
+
+ /* pwdb override (rxconfig<5>) to turn on RX LDO indpendent of
+ * pwdb controls from DSP_TAP10
+ */
+ bcm_phy_write_misc(phydev, 0x003a, 0x0001, 0x0020);
+
+ /* Remove references to channel 2 and 3 */
+ bcm_phy_write_misc(phydev, 0x003b, 0x0002, 0x0000);
+ bcm_phy_write_misc(phydev, 0x003b, 0x0003, 0x0000);
+
+ /* Set cal_bypassb bit rxconfig<43> */
+ bcm_phy_write_misc(phydev, 0x003a, 0x0003, 0x0800);
+ udelay(2);
+
+ /* Revert pwdb_override (rxconfig<5>) to 0 so that the RX pwr
+ * is controlled by DSP.
+ */
+ bcm_phy_write_misc(phydev, 0x003a, 0x0001, 0x0000);
+
+ /* Drop LSB */
+ rcalnewcode11d2 = (rcalnewcode11 & 0xfffe) / 2;
+ tmp = bcm_phy_read_misc(phydev, 0x003d, 0x0001);
+ /* Clear bits [11:5] */
+ tmp &= ~0xfe0;
+ /* set txcfg_ch0<5>=1 (enable + set local rcal) */
+ tmp |= 0x0020 | (rcalnewcode11d2 * 64);
+ bcm_phy_write_misc(phydev, 0x003d, 0x0001, tmp);
+ bcm_phy_write_misc(phydev, 0x003d, 0x0002, tmp);
+
+ tmp = bcm_phy_read_misc(phydev, 0x003d, 0x0000);
+ /* set txcfg<45:44>=11 (enable Rextra + invert fullscaledetect)
+ */
+ tmp &= ~0x3000;
+ tmp |= 0x3000;
+ bcm_phy_write_misc(phydev, 0x003d, 0x0000, tmp);
+
+ return 0;
+ }
+
+ static int bcm7xxx_16nm_ephy_config_init(struct phy_device *phydev)
+ {
+ int ret, val;
+
+ ret = bcm7xxx_16nm_ephy_afe_config(phydev);
+ if (ret)
+ return ret;
+
+ ret = bcm_phy_set_eee(phydev, true);
+ if (ret)
+ return ret;
+
+ ret = bcm_phy_read_shadow(phydev, BCM54XX_SHD_SCR3);
+ if (ret < 0)
+ return ret;
+
+ val = ret;
+
+ /* Auto power down of DLL enabled,
+ * TXC/RXC disabled during auto power down.
+ */
+ val &= ~BCM54XX_SHD_SCR3_DLLAPD_DIS;
+ val |= BIT(8);
+
+ ret = bcm_phy_write_shadow(phydev, BCM54XX_SHD_SCR3, val);
+ if (ret < 0)
+ return ret;
+
+ return bcm_phy_enable_apd(phydev, true);
+ }
+
+ static int bcm7xxx_16nm_ephy_resume(struct phy_device *phydev)
+ {
+ int ret;
+
+ /* Re-apply workarounds coming out suspend/resume */
+ ret = bcm7xxx_16nm_ephy_config_init(phydev);
+ if (ret)
+ return ret;
+
+ return genphy_config_aneg(phydev);
+ }
+
static int bcm7xxx_28nm_ephy_resume(struct phy_device *phydev)
{
int ret;

Attachment: pgpEQlwDeNwWf.pgp
Description: OpenPGP digital signature

Next message: Alan Stern: "Re: [PATCH v2 1/6] driver core: Move the "authorized" attribute from USB/Thunderbolt to core"
Previous message: Matteo Croce: "Re: [PATCH v5 1/3] riscv: optimized memcpy"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]