[RFC PATCH 2/4] pinctrl: pinconf-generic: Add support for "output-impedance" to be extracted from DT files

[Lad Prabhakar]

Add "output-impedance" property to generic options used for DT parsing
files. This enables drivers, which use generic pin configurations, to
get the value passed to this property.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
---
 drivers/pinctrl/pinconf-generic.c       | 2 ++
 include/linux/pinctrl/pinconf-generic.h | 3 +++
 2 files changed, 5 insertions(+)

diff --git a/drivers/pinctrl/pinconf-generic.c b/drivers/pinctrl/pinconf-generic.c
index 22e8d4c4040e..3bff4e4340b9 100644
--- a/drivers/pinctrl/pinconf-generic.c
+++ b/drivers/pinctrl/pinconf-generic.c
@@ -46,6 +46,7 @@ static const struct pin_config_item conf_items[] = {
 	PCONFDUMP(PIN_CONFIG_MODE_LOW_POWER, "pin low power", "mode", true),
 	PCONFDUMP(PIN_CONFIG_OUTPUT_ENABLE, "output enabled", NULL, false),
 	PCONFDUMP(PIN_CONFIG_OUTPUT, "pin output", "level", true),
+	PCONFDUMP(PIN_CONFIG_OUTPUT_IMPEDANCE, "output impedance", "ohm", true),
 	PCONFDUMP(PIN_CONFIG_POWER_SOURCE, "pin power source", "selector", true),
 	PCONFDUMP(PIN_CONFIG_SLEEP_HARDWARE_STATE, "sleep hardware state", NULL, false),
 	PCONFDUMP(PIN_CONFIG_SLEW_RATE, "slew rate", NULL, true),
@@ -179,6 +180,7 @@ static const struct pinconf_generic_params dt_params[] = {
 	{ "output-disable", PIN_CONFIG_OUTPUT_ENABLE, 0 },
 	{ "output-enable", PIN_CONFIG_OUTPUT_ENABLE, 1 },
 	{ "output-high", PIN_CONFIG_OUTPUT, 1, },
+	{ "output-impedance", PIN_CONFIG_OUTPUT_IMPEDANCE, 0 },
 	{ "output-low", PIN_CONFIG_OUTPUT, 0, },
 	{ "power-source", PIN_CONFIG_POWER_SOURCE, 0 },
 	{ "sleep-hardware-state", PIN_CONFIG_SLEEP_HARDWARE_STATE, 0 },
diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index eee0e3948537..e6293ebd4052 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -91,6 +91,8 @@ struct pinctrl_map;
  * 	configuration (eg. the currently selected mux function) drive values on
  * 	the line. Use argument 1 to enable output mode, argument 0 to disable
  * 	it.
+ * @PIN_CONFIG_OUTPUT_IMPEDANCE: this will configure the pins output impedance with
+ *	 the value passed as argument. The argument is in ohm.
  * @PIN_CONFIG_PERSIST_STATE: retain pin state across sleep or controller reset
  * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
  *	supplies, the argument to this parameter (on a custom format) tells
@@ -129,6 +131,7 @@ enum pin_config_param {
 	PIN_CONFIG_MODE_PWM,
 	PIN_CONFIG_OUTPUT,
 	PIN_CONFIG_OUTPUT_ENABLE,
+	PIN_CONFIG_OUTPUT_IMPEDANCE,
 	PIN_CONFIG_PERSIST_STATE,
 	PIN_CONFIG_POWER_SOURCE,
 	PIN_CONFIG_SKEW_DELAY,
-- 
2.17.1