Re: [RFC PATCH 4/4] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set drive-strength and output-impedance

[Geert Uytterhoeven]

Hi Prabhakar,

On Thu, Sep 30, 2021 at 2:17 PM Lad Prabhakar
<prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> wrote:
> Add support to get/set drive-strength and output-impedance of the pins.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>

Thanks for your patch!

> --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> @@ -47,6 +47,7 @@
>  #define PIN_CFG_FILONOFF               BIT(9)
>  #define PIN_CFG_FILNUM                 BIT(10)
>  #define PIN_CFG_FILCLKSEL              BIT(11)
> +#define PIN_CFG_GROUP_B                        BIT(12)

Perhaps it would be easier to have separate PIN_CFG_IOLH_A and
PIN_CFG_IOLH_B flags, instead of a PIN_CFG_IOLH flag and a
PIN_CFG_GROUP_B modifier flag?

>
>  #define RZG2L_MPXED_PIN_FUNCS          (PIN_CFG_IOLH | \
>                                          PIN_CFG_SR | \

> @@ -484,6 +513,38 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>                 break;
>         }
>
> +       case PIN_CONFIG_OUTPUT_IMPEDANCE:
> +       case PIN_CONFIG_DRIVE_STRENGTH: {
> +               unsigned int mA[4] = { 2, 4, 8, 12 };
> +               unsigned int oi[4] = { 100, 66, 50, 33 };

static const

> +
> +               if (param == PIN_CONFIG_DRIVE_STRENGTH) {
> +                       if (!(cfg & PIN_CFG_IOLH) || groupb_pin)
> +                               return -EINVAL;
> +               } else {
> +                       if (!(cfg & PIN_CFG_IOLH) || !groupb_pin)
> +                               return -EINVAL;
> +               }
> +
> +               spin_lock_irqsave(&pctrl->lock, flags);
> +
> +               /* handle _L/_H for 32-bit register read/write */
> +               addr = pctrl->base + IOLH(port);
> +               if (bit >= 4) {
> +                       bit -= 4;
> +                       addr += 4;
> +               }
> +
> +               reg = readl(addr) & (IOLH_MASK << (bit * 8));
> +               reg = reg >> (bit * 8);
> +               if (param == PIN_CONFIG_DRIVE_STRENGTH)
> +                       arg = mA[reg];
> +               else
> +                       arg = oi[reg];
> +               spin_unlock_irqrestore(&pctrl->lock, flags);

I think you've reached the point where it starts to make sense to
have helper functions to read and modify these sub-register fields
that may be located into the current or next register.

And after that, you can split it in two smaller separate cases for
drive strength and output impedance.

> +               break;
> +       }
> +
>         default:
>                 return -ENOTSUPP;
>         }

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds