Re: [PATCH v4 00/20] Enable Qualcomm Crypto Engine on sm8250

[Bhupesh Sharma]

Hi Thara,

On Wed, 20 Oct 2021 at 19:33, Thara Gopinath <thara.gopinath@xxxxxxxxxx> wrote:
>
> On 10/13/21 6:55 AM, Bhupesh Sharma wrote:
> > Sorry for a delayed v4, but I have been caught up with some other
> > patches.
>
> Hi Bhupesh,
>
> If possible, please consider splitting this series into 2. One with
> changes required to support crypto driver on
> sm8250 and other with the generic fixes / fixing the dt-bindings et all.
> It would be easier to review as well

That's a good suggestion, but I would suggest keeping the series as
one for now (as we are already approaching v5 and most of the review
comments are taken care of in v5).

Regards,
Bhupesh

> > Changes since v3:
> > =================
> > - v3 can be seen here: https://lore.kernel.org/linux-arm-msm/20210519143700.27392-1-bhupesh.sharma@xxxxxxxxxx/
> > - Dropped a couple of patches from v3, on basis of the review comments:
> >     ~ [PATCH 13/17] crypto: qce: core: Make clocks optional
> >     ~ [PATCH 15/17] crypto: qce: Convert the device found dev_dbg() to dev_info()
> > - Addressed review comments from Thara, Rob and Stephan Gerhold.
> > - Collect Reviewed-by from Rob and Thara on some of the patches from the
> >    v3 patchset.
> >
> > Changes since v2:
> > =================
> > - v2 can be seen here: https://lore.kernel.org/dmaengine/20210505213731.538612-1-bhupesh.sharma@xxxxxxxxxx/
> > - Drop a couple of patches from v1, which tried to address the defered
> >    probing of qce driver in case bam dma driver is not yet probed.
> >    Replace it instead with a single (simpler) patch [PATCH 16/17].
> > - Convert bam dma and qce crypto dt-bindings to YAML.
> > - Addressed review comments from Thara, Bjorn, Vinod and Rob.
> >
> > Changes since v1:
> > =================
> > - v1 can be seen here: https://lore.kernel.org/linux-arm-msm/20210310052503.3618486-1-bhupesh.sharma@xxxxxxxxxx/
> > - v1 did not work well as reported earlier by Dmitry, so v2 contains the following
> >    changes/fixes:
> >    ~ Enable the interconnect path b/w BAM DMA and main memory first
> >      before trying to access the BAM DMA registers.
> >    ~ Enable the interconnect path b/w qce crytpo and main memory first
> >      before trying to access the qce crypto registers.
> >    ~ Make sure to document the required and optional properties for both
> >      BAM DMA and qce crypto drivers.
> >    ~ Add a few debug related print messages in case the qce crypto driver
> >      passes or fails to probe.
> >    ~ Convert the qce crypto driver probe to a defered one in case the BAM DMA
> >      or the interconnect driver(s) (needed on specific Qualcomm parts) are not
> >      yet probed.
> >
> > Qualcomm crypto engine is also available on sm8250 SoC.
> > It supports hardware accelerated algorithms for encryption
> > and authentication. It also provides support for aes, des, 3des
> > encryption algorithms and sha1, sha256, hmac(sha1), hmac(sha256)
> > authentication algorithms.
> >
> > Tested the enabled crypto algorithms with cryptsetup test utilities
> > on sm8250-mtp and RB5 board (see [1]) and also with crypto self-tests,
> > including the fuzz tests (CONFIG_CRYPTO_MANAGER_EXTRA_TESTS=y).
> >
> > Note that this series is rebased on a SMMU related fix from Arnd applied
> > on either linus's tip of linux-next's tip (see [2]), without which
> > the sm8250 based boards fail to boot with the latest tip.
> >
> > [1]. https://linux.die.net/man/8/cryptsetup
> > [2]. https://lore.kernel.org/linux-arm-kernel/CAA8EJpoD4Th1tdwYQLnZur2oA0xX0LojSrNFLyJqdi6+rnB3YQ@xxxxxxxxxxxxxx/T/
> >
> > Cc: Thara Gopinath <thara.gopinath@xxxxxxxxxx>
> > Cc: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> > Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> >
> > Bhupesh Sharma (17):
> >    arm64/dts: qcom: Fix 'dma' & 'qcom,controlled-remotely' nodes in dts
> >    arm64/dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg'
> >      property
> >    arm64/dts: qcom: ipq6018: Remove unused 'iface_clk' property from
> >      dma-controller node
> >    dt-bindings: qcom-bam: Convert binding to YAML
> >    dt-bindings: qcom-bam: Add 'interconnects' & 'interconnect-names' to
> >      optional properties
> >    dt-bindings: qcom-bam: Add 'iommus' to optional properties
> >    dt-bindings: qcom-qce: Convert bindings to yaml
> >    dt-bindings: qcom-qce: Add 'interconnects' and move 'clocks' to
> >      optional properties
> >    dt-bindings: qcom-qce: Add 'iommus' to optional properties
> >    arm64/dts: qcom: sdm845: Use RPMH_CE_CLK macro directly
> >    dt-bindings: crypto : Add new compatible strings for qcom-qce
> >    arm64/dts: qcom: Use new compatibles for crypto nodes
> >    crypto: qce: Add new compatibles for qce crypto driver
> >    crypto: qce: Print a failure msg in case probe() fails
> >    crypto: qce: Defer probing if BAM dma channel is not yet initialized
> >    crypto: qce: Add 'sm8250-qce' compatible string check
> >    arm64/dts: qcom: sm8250: Add dt entries to support crypto engine.
> >
> > Thara Gopinath (3):
> >    dma: qcom: bam_dma: Add support to initialize interconnect path
> >    crypto: qce: core: Add support to initialize interconnect path
> >    crypto: qce: core: Make clocks optional
> >
> >   .../devicetree/bindings/crypto/qcom-qce.yaml  |  90 +++++++++++++++
> >   .../devicetree/bindings/dma/qcom_bam_dma.txt  |  50 --------
> >   .../devicetree/bindings/dma/qcom_bam_dma.yaml | 107 ++++++++++++++++++
> >   arch/arm64/boot/dts/qcom/ipq6018.dtsi         |  10 +-
> >   arch/arm64/boot/dts/qcom/ipq8074.dtsi         |   4 +-
> >   arch/arm64/boot/dts/qcom/msm8996.dtsi         |   4 +-
> >   arch/arm64/boot/dts/qcom/msm8998.dtsi         |   2 +-
> >   arch/arm64/boot/dts/qcom/sdm845.dtsi          |  10 +-
> >   arch/arm64/boot/dts/qcom/sm8250.dtsi          |  28 +++++
> >   drivers/crypto/qce/core.c                     |  66 +++++++----
> >   drivers/crypto/qce/core.h                     |   1 +
> >   drivers/dma/qcom/bam_dma.c                    |  16 ++-
> >   12 files changed, 302 insertions(+), 86 deletions(-)
> >   create mode 100644 Documentation/devicetree/bindings/crypto/qcom-qce.yaml
> >   delete mode 100644 Documentation/devicetree/bindings/dma/qcom_bam_dma.txt
> >   create mode 100644 Documentation/devicetree/bindings/dma/qcom_bam_dma.yaml
> >
>
>