[PATCH 1/2] wcn36xx: populate band before determining rate on RX
From: Benjamin Li
Date: Thu Oct 28 2021 - 18:32:27 EST
status.band is used in determination of status.rate -- for 5GHz on legacy
rates there is a linear shift between the BD descriptor's rate field and
the wcn36xx driver's rate table (wcn_5ghz_rates).
We have a special clause to populate status.band for hardware scan offload
frames. However, this block occurs after status.rate is already populated.
Correctly handle this dependency by moving the band block before the rate
block.
This patch addresses kernel warnings & missing scan results for 5GHz APs
that send their probe responses at the higher four legacy rates (24-54
Mbps), when using hardware scan offload:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at net/mac80211/rx.c:4532 ieee80211_rx_napi+0x744/0x8d8
Modules linked in: wcn36xx [...]
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.19.107-g73909fa #1
Hardware name: Square, Inc. T2 (all variants) (DT)
Call trace:
dump_backtrace+0x0/0x148
show_stack+0x14/0x1c
dump_stack+0xb8/0xf0
__warn+0x2ac/0x2d8
warn_slowpath_null+0x44/0x54
ieee80211_rx_napi+0x744/0x8d8
ieee80211_tasklet_handler+0xa4/0xe0
tasklet_action_common+0xe0/0x118
tasklet_action+0x20/0x28
__do_softirq+0x108/0x1ec
irq_exit+0xd4/0xd8
__handle_domain_irq+0x84/0xbc
gic_handle_irq+0x4c/0xb8
el1_irq+0xe8/0x190
lpm_cpuidle_enter+0x220/0x260
cpuidle_enter_state+0x114/0x1c0
cpuidle_enter+0x34/0x48
do_idle+0x150/0x268
cpu_startup_entry+0x20/0x24
rest_init+0xd4/0xe0
start_kernel+0x398/0x430
---[ end trace ae28cb759352b403 ]---
Fixes: 8a27ca394782 ("wcn36xx: Correct band/freq reporting on RX")
Signed-off-by: Benjamin Li <benl@xxxxxxxxxxxx>
---
drivers/net/wireless/ath/wcn36xx/txrx.c | 37 +++++++++++++------------
1 file changed, 19 insertions(+), 18 deletions(-)
diff --git a/drivers/net/wireless/ath/wcn36xx/txrx.c b/drivers/net/wireless/ath/wcn36xx/txrx.c
index 75951ccbc840e..f0a9f069a92a9 100644
--- a/drivers/net/wireless/ath/wcn36xx/txrx.c
+++ b/drivers/net/wireless/ath/wcn36xx/txrx.c
@@ -314,8 +314,6 @@ int wcn36xx_rx_skb(struct wcn36xx *wcn, struct sk_buff *skb)
fc = __le16_to_cpu(hdr->frame_control);
sn = IEEE80211_SEQ_TO_SN(__le16_to_cpu(hdr->seq_ctrl));
- status.freq = WCN36XX_CENTER_FREQ(wcn);
- status.band = WCN36XX_BAND(wcn);
status.mactime = 10;
status.signal = -get_rssi0(bd);
status.antenna = 1;
@@ -327,6 +325,25 @@ int wcn36xx_rx_skb(struct wcn36xx *wcn, struct sk_buff *skb)
wcn36xx_dbg(WCN36XX_DBG_RX, "status.flags=%x\n", status.flag);
+ if (bd->scan_learn) {
+ /* If packet originate from hardware scanning, extract the
+ * band/channel from bd descriptor.
+ */
+ u8 hwch = (bd->reserved0 << 4) + bd->rx_ch;
+
+ if (bd->rf_band != 1 && hwch <= sizeof(ab_rx_ch_map) && hwch >= 1) {
+ status.band = NL80211_BAND_5GHZ;
+ status.freq = ieee80211_channel_to_frequency(ab_rx_ch_map[hwch - 1],
+ status.band);
+ } else {
+ status.band = NL80211_BAND_2GHZ;
+ status.freq = ieee80211_channel_to_frequency(hwch, status.band);
+ }
+ } else {
+ status.band = WCN36XX_BAND(wcn);
+ status.freq = WCN36XX_CENTER_FREQ(wcn);
+ }
+
if (bd->rate_id < ARRAY_SIZE(wcn36xx_rate_table)) {
rate = &wcn36xx_rate_table[bd->rate_id];
status.encoding = rate->encoding;
@@ -353,22 +370,6 @@ int wcn36xx_rx_skb(struct wcn36xx *wcn, struct sk_buff *skb)
ieee80211_is_probe_resp(hdr->frame_control))
status.boottime_ns = ktime_get_boottime_ns();
- if (bd->scan_learn) {
- /* If packet originates from hardware scanning, extract the
- * band/channel from bd descriptor.
- */
- u8 hwch = (bd->reserved0 << 4) + bd->rx_ch;
-
- if (bd->rf_band != 1 && hwch <= sizeof(ab_rx_ch_map) && hwch >= 1) {
- status.band = NL80211_BAND_5GHZ;
- status.freq = ieee80211_channel_to_frequency(ab_rx_ch_map[hwch - 1],
- status.band);
- } else {
- status.band = NL80211_BAND_2GHZ;
- status.freq = ieee80211_channel_to_frequency(hwch, status.band);
- }
- }
-
memcpy(IEEE80211_SKB_RXCB(skb), &status, sizeof(status));
if (ieee80211_is_beacon(hdr->frame_control)) {
--
2.25.1